爆炸激波管管口稀疏波对试验段的影响

数值模拟了爆炸激波管不同隔离段长度时管口稀疏波对试验段超压的影响。为了准确高效地模拟试验段入口的超压曲线,采用了一种将一维球对称程序和三维程序相结合的计算方法,并在一维计算中利用爆炸相似律,采用小当量爆炸来模拟实际超压波形。计算结果表明,隔离段长度L的变化不影响超压峰值;L小于等于20m时,稀疏波的影响使得试验段超压的作用时间、比冲量减小;L大于等于30m时,稀疏波对试验段超压无影响。     

基于均匀实验设计的温压战斗部爆炸冲击波毁伤仿真研究

以温压战斗部爆炸冲击波对地下目标的毁伤为背景,设计毁伤仿真模拟的基本方案,在对影响冲击波毁伤因素合理分析的基础上,利用均匀试验设计方法设计以装药密度、空气温度、大气压强以及混凝土密度为影响因素的均匀试验方案,最后通过正态分布检验图和Bootstrap法等方法对毁伤参数的统计特性进行研究。结果表明,固定条件下温压战斗部爆炸冲击波对地下目标的毁伤中,毁伤参数值具有明显的正态分布特性,对后续结合现场试验数据确定毁伤参数真值和毁伤试验鉴定提供了一定的指导和借鉴作用。     

Chain damage effects of multi-spaced plates by reactive jet impact

Chain damage is a new phenomenon that occurs when a reactive jet impacts and penetrates multi-spaced plates.The reactive jet produces mechanical perforations on the spaced plates by its kinetic energy(KE),and then results in unusual chain rupturing effects and excessive structural damage on the spaced plates by its deflagration reaction.In the present study,the chain damage behavior is initially demonstrated by experiments.The reactive liners,composed of 26 wt％Al and 74 wt％PTFE,are fabricated through a pressing and sintering process.Three reactive liner thicknesses of 0.08 CD,0.10 CD and 0.12 CD(charge diameter)are chosen to carry out the chain damage experiments.The results show a chain rupturing phenomenon caused by reactive jet.The constant reaction delay time and the different penetration velocities of reactive jets from liners with different thicknesses result in the variation of the deflagration position,which consequently determines the number of ruptured plates behind the armor.Then,the finite-element code AUTODYN-3D has been used to simulate the kinetic energy only-induced rupturing effects on plates,based on the mechanism of behind armor debris(BAD).The significant discrepancies between simulations and experiments indicate that one enhanced damage mechanism,the behind armor blast(BAB),has acted on the ruptured plates.Finally,a theoretical model is used to consider the BAB-induced enhancement,and the analysis shows that the rupturing area on aluminum plates depends strongly upon the KE only-induced pre-perforations,the mass of reactive materials,and the thickness of plates.     

一种新型防护结构对爆炸冲击波衰减特性的研究

运用大型有限元软件LS—DYNA,在相同爆炸冲击波作用下,对洞库口部普通钢板防护门和有泡沫铝夹层的钢板防护门两种防护结构的隔爆性能进行了数值模拟和对比分析,结果表明:有泡沫铝夹层的钢板防护门对爆炸冲击波有着良好的衰减特性。同时表明该新型防护结构对洞库口部抗爆炸冲击波设计有着很高的参考价值。     

基于探雷信息的火箭深弹炸雷效能研究

针对火箭深弹传统炸雷方式中存在的盲目性、危险性及耗弹量大等问题,提出了火箭深弹与探雷声纳协同定点炸除水雷的方法,建立了基于随机模拟的火箭深弹炸雷效能评估模型。实例解算结果表明,火箭深弹对水雷毁伤概率随着射距的增加而增大;在同一射距下,毁伤概率随射向与探测方向夹角的增加而增大,但在最优(大)夹角附近毁伤概率变化不大。通过该模型能有效解算出火箭深弹对水雷的毁伤效果,进而得到最优射击诸元和最大毁伤概率,对火箭深弹炸雷技术实施提供了理论基础。     

激波灭火技术的初步研究

讨论了激波灭火技术的基本原理， 给出可行的研究路线。采用新型的计算效率较高的ＥＮＯ差分格式， 从非定常ＥＵＬＥＲ方程出发， 对近地爆炸波产生的流场进行数值模拟， 分析后认为控制爆炸波后风场是关键。     

方孔蜂窝夹层板在爆炸载荷下的动态响应

通过有限元数值模拟方法,对方孔蜂窝夹层板在爆炸冲击载荷下的动态响应和变形机理进行了分析.在单位面积质量以及夹芯层的高度、宽度给定的情况下,得出了最优的夹芯层相对密度.在此相对密度下,夹层板吸收能量最多,下面板变形最小,夹层板的抗冲击性能最优.将单位面积质量相等的夹层板和实体板进行了对比分析,结果表明:夹层板具有更加优良...     

封闭式爆炸容器小药量爆炸振动效应研究

为评估炸药在封闭容器内爆炸产生的振动效应对周围环境的影响,对封闭式爆炸容器小药量TNT炸药爆炸产生的爆炸振动效应进行了爆源邻近实地监测和测试。结果表明:小药量炸药爆炸引起的爆炸振动效应对距爆源100 m以外的普通砖结构民用住宅产生的速度强度远低于其临界峰值速度,不会对其结构产生明显影响。     

关于圆柱壳在水下爆炸冲击波作用下二次加载现象的数值模拟研究

运用大型商业有限元程序MSC.DYTRAN数值模拟了水下爆炸冲击波载荷作用下自由环肋圆柱壳的非线性动态响应.采用一般耦合算法(generalcoupling)模拟流体与结构的耦合效应,计算中考虑了材料的应变率强化效应,几何非线性的影响,分析了空穴现象的产生和二次加载对结构响应的影响.仿真结果表明,相同工况和厚度下的无限自由平板和自由环肋圆柱壳,后者的空化时间比前者长,而壳体运动的最大速度后者比前者低.     

Evaluation of effectiveness of polymer coatings in reducing blast-induced deformation of steel plates

Incorporating elastomers such as polymers in protective structures to withstand high energetic dynamic loads, has gained significant interest. The main objective of this study is to investigate the influence of a Polyurea coating towards the blast-induced response in steel plates. As such, Polyurea coated steel plates were tested under near-field blast loads, produced by the detonation of 1 kg of spherical nitromethane charges, at a standoff distance of 150 mm. Mild steel (XLERPLATE 350) and high-strength steel (BIS80) plates with thicknesses of 10 mm were Polyurea coated with thicknesses of 6 mm and 12 mm on either the front (facing the charge) or the back face. The deformation profiles were measured using 3D scanning. Numerical simulations were performed using the non-linear finite element code LS-DYNA. The strain-dependent behaviour of the steel and Polyurea were represented by Johnson-cook and Money-Rivlin constitutive models, respectively. The numerical models were validated by comparing the plate deflection results obtained from the experiments and were then used in the subsequent parametric study to investigate the optimum thickness of the Polyurea coating. The results indicate that back face coating contributes towards an approximately 20% reduction in the residual deformation as well as the absence of melting of the Polyurea layer, while the front-face coating can be used a means of providing additional standoff distance to the steel plates.