Influence of propagation direction on operation performance of rotating detonation combustor with turbine guide vane

Due to the pressure gain combustion characteristics, the rotating detonation combustor (RDC) can enhance thermodynamic cycle efficiency. Therefore, the performance of gas-turbine engine can be further improved with this combustion technology. In the present study, the RDC operation performance with a turbine guide vane (TGV) is experimentally investigated. Hydrogen and air are used as propellants while hydrogen and air mass flow rate are about 16.1 g/s and 500 g/s and the equivalence ratio is about 1.0. A pre-detonator is used to ignite the mixture. High-frequency dynamic pressure transducers and silicon pressure sensors are employed to measure pressure oscillations and static pressure in the combustion chamber. The experimental results show that the steady propagation of rotating detonation wave (RDW) is observed in the combustion chamber and the mean propagation velocity is above 1650 m/s, reaching over 84% of theoretical Chapman-Jouguet detonation velocity. Clockwise and counterclockwise propagation directions of RDW are obtained. For clockwise propagation direction, the static pressure is about 15% higher in the combustor compared with counterclockwise propagation direction, but the RDW dominant frequency is lower. When the oblique shock wave propagates across the TGV, the pressure oscillations reduces significantly. In addition, as the detonation products flow through the TGV, the static pressure drops up to 32% and 43% for clockwise and counterclockwise propagation process respectively.     

Effects of total pressures and equivalence ratios on kerosene/air rotating detonation engines using a paralleling CE/SE method

In this paper, the kerosene/air rotating detonation engines(RDE) are numerically investigated, and the emphasis is laid on the effects of total pressures and equivalence ratios on the operation characteristics of RDE including the initiation, instabilities, and propulsive performance. A hybrid MPI + OpenMP parallel computing model is applied and it is proved to be able to obtain a more effective parallel performance on high performance computing(HPC) systems. A series of cases with the total pressure of 1 MPa, 1.5 MPa, 2 MPa, and the equivalence ratio of 0.9, 1, 1.4 are simulated. On one hand, the total pressure shows a significant impact on the instabilities of rotating detonation waves. The instability phenomenon is observed in cases with low total pressure (1 MPa) and weakened with the increase of the total pressure. The total pressure has a small impact on the detonation wave velocity and the specific impulse. On the other hand, the equivalence ratio shows a negligible influence on the instabilities, while it affects the ignition process and accounts for the detonation velocity deficit. It is more difficult to initiate rotating detonation waves directly in the lean fuel operation condition. Little difference was observed in the thrust with different equivalence ratios of 0.9, 1, and 1.4. The highest specific impulse was obtained in the lean fuel cases, which is around 2700 s. The findings could provide insights into the understanding of the operation characteristics of kerosene/air RDE.     

空气/煤油/水燃气发生器点火特性试验研究

燃气发生器是超燃冲压发动机地面试验系统中的关键设备,为提高系统安全性和经济性设计了空气/煤油/水燃气发生器,在富燃状态下进行了一系列点火试验,试验结果表明：该型燃气发生器,实现可靠点火的余氧系数下限为0.51;水的加入使得化学反应速率和火焰传播速度降低,燃气发生器点火和火焰稳定困难,提高余氧系数可以提高点火可靠性。同时水的加入容易引起燃烧不稳定,通过提高余氧系数可消除低频不稳定燃烧。     

空气/煤油/水燃气发生器点火特性试验

燃气发生器是超燃冲压发动机地面试验系统中的关键设备,为提高系统安全性和经济性设计了空气/煤油/水燃气发生器,在富燃状态下进行了一系列点火试验,试验结果表明:该型燃气发生器,实现可靠点火的余氧系数下限为0.51;水的加入使得化学反应速率和火焰传播速度降低,燃气发生器点火和火焰稳定困难,提高余氧系数可以提高点火可靠性。同时,水的加入容易引起燃烧不稳定,通过提高余氧系数来消除低频不稳定燃烧。     

Gliding arc plasma adjusting pre-combustion cracking products

In view of the difficulty of kerosene-air detonation faced by the application of rotating detonation to aviation engines, in order to improve the kerosene detonation activity, the atmospheric pressure gliding arc plasma is used to conduct secondary adjustment of the pre-combustion cracking products. The results show that the components with larger molecular weight in the pre-combustion cracking products, such as ethylene and methane, can be cracked into highly active species of hydrogen and acetylene by gliding arc plasma. With the increase of the fuel ratio of pre-combustion cracking, the plasma has a more significant effect on the adjustment of high active components. However, as the flow rate of the cracking gas treated by plasma increases, the adjustment effect is obviously reduced.     

Experimental study on the detonation process of a pulse detonation engine with ionized seeds

An experimental platform of a pulse detonation engine (PDE) was established to study the effect of different K₂CO₃ ionized seed mass contents on the detonation process. The pressure and ion concentration were detected in the detonation process of the PDE with different contents of ionized seeds. The initiation process of the PDE at different ignition frequencies was studied. The results show that the gas conductivity in the detonation process increased by adding ionized seeds to the PDE tube, and the conductivity increased with the increase in ionized seed mass content. With the increase in ionized seed mass content, the range of the conductivity decreased. The PDE was successfully ignited and formed a stable detonation wave at ignition frequencies of 5 Hz and 10 Hz, and the peak pressure of the stable detonation with the ignition frequency of 5 Hz was 17% higher than that with an ignition frequency of 10 Hz. The detonation wave intensity was weakened and degenerated to a shock wave that propagated in the tube without the fuel filled at the ignition frequency of 20 Hz.     

连续旋转爆震波传播模态试验

通过保持空气流量不变、改变H2/air当量比开展了连续旋转爆震对比试验,发现随当量比的降低出现三种传播模态:在较高的当量比(0.90~1.86)下,连续旋转爆震波以同向传播模态传播;在较低的当量比(≈0.75)下,则以双波对撞模态传播;在中间工况,则以上述混合模态维持传播。分析了不同传播模态下的高频压力特征,并初步分析了传播模态的转换机制:当量比较高时,爆震强度较高,传播过程中的损失和速度亏损相对较小,爆震波以同向传播模态维持传播;当量比较低时,爆震强度较低,传播过程中的损失和速度亏损较大,此时无法维持同向传播模态,而以双波对撞模态传播,这是由于双波对撞模态中的激波对撞产生高温环境,有利于燃烧放热,其可能是连续旋转爆震的极限传播模态。     

强脉冲 CO2 激光与靶的相互作用

在真空背景下的实验表明,当微秒量级的强脉冲激光与靶材相互作用时,由于靶材的升华,激光维持爆震波依然存在。爆震波产生的压缩波传入靶内,该应力波的作用是材料破坏的重要因素。而强脉冲激光引起的汽化反冲压力、热应力和烧蚀破坏也是不可忽视的因素。实验还表明,在真空背景下维持爆震波足以将后续激光屏蔽。     

Experimental investigation on enhanced damage to fuel tanks by reactive projectiles impact

Enhanced damage to the full-filled fuel tank,impacted by the cold pressed and sintered PTFE/AL/W reactive material projectile(RMP)with a density of 7.8 g/cm3,is investigated experimentally and theoretically.The fuel tank is a rectangular structure,welded by six pieces of 2024 aluminum plate with a thickness of 6 mm,and filled with RP-3 aviation kerosene.Experimental results show that the kerosene is ignited by the RMP impact at a velocity above 1062 m/s,and a novel interior ignition phenomenon which is closely related to the rupture effect of the fuel tank is observed.However,the traditional steel projectile with the same mass and dimension requires a velocity up to 1649 m/s to ignite the kerosene.Based on the experimental results,the radial pressure field is considered to be the main reason for the shear failure of weld.For mechanism considerations,the chemical energy released by the RMP enhances the hydrodynamic ram(HRAM)effect and provides additional ignition sources inside the fuel tank,thereby enhancing both rupture and ignition effects.Moreover,to further understand the enhanced ignition effect of RMP,the reactive debris temperature inside the kerosene is analyzed theoretically.The initiated reactive debris with high temperature provides effective interior ignition sources to ignite the kerosene,resulting in the enhanced ignition of the kerosene.     

燃烧加热型煤油加热器工作特性试验

针对冲压发动机地面试验应用需求,设计了基于燃气加热方式的煤油加热器,通过试验的方法研究了多个因素对其工作特性的影响规律。研究结果表明,该煤油加热器加热能力强,响应时间短,可在线制备超临界/裂解态煤油;其中,燃气温度、流量和煤油流量是影响煤油加热器工作特性的主要因素,通过控制燃气温度和流量可以大范围调节煤油温度,能满足冲压发动机不同试验工况的应用需求。     

煤油超音速燃烧的试验研究

在地面直连式试车台上,研究了煤油碳氢燃料超燃冲压发动机的点火燃烧性能。通过测量模型发动机壁面压力分布,比较了不同工况下的煤油点火燃烧性能。试验结果表明,在当量比为0.27～1.46的大范围内,煤油在超燃冲压模型发动机中能够成功点火,支板和凹腔对煤油在超声速气流中的点火及稳定燃烧有重要作用,少量氢气的喷入对煤油的点火燃烧有良好的促进作用。太厚的支板、过高的当量比、模型发动机第一级燃烧室加入燃料过多会使发动机壅塞,影响隔离段的正常工作,进而影响加热器喷管工作。     

多点偏心起爆对破片速度增益的影响

多点偏心起爆后,爆轰波相互作用在定向区域内产生了马赫波超压,使得该区域破片速度产生增益.利用爆轰波反射理论,建立多点偏心起爆后爆轰波相互作用特性的理论模型,并确定定向区内破片速度的增益特性.3种不同起爆方式的仿真计算和静爆试验结果对比表明,定向区内不同起爆方式得到的破片增益程度较为吻合.     

1D study of the detonation phenomenon and its influence on the interior ballistics of the combustion light gas gun

One-dimensional simulations with a detailed hydrogen-oxygen reaction mechanism have been performed to investigate detonation phenomenon in a combustion light gas gun (CLGG). Convection fluxes of the Navier-Stokes equations are solved using the WAF (weighted average flux) scheme HLLC Riemann solver. A high resolution fifth-order WENO scheme for the variable extrapolation at the volume interface and a fourth-order Runge-Kutta scheme for the time advancement are used. Validation tests of the stoichiometric hydrogen-oxygen deflagration to detonation transition process shows good agreement between the computed results and the analytical and documented solutions, demonstrating the reliability on the detonation simulation of the current scheme. Simulation results of the interior ballistic process of the CLGG show that the flame propagation experiences three distinct stages. The blast detonation wave causes a high-pressure shock and hazardous oscillations in the chamber and makes the projectile accelerate with fluctuations, but has only a small improvement to the muzzle velocity.     

Fracture mechanism of a cylindrical shell cut by circumferential detonation collision

The failure mechanism of a cylindrical shell cut into fragments by circumferential detonation collision was experimentally and numerically investigated. A self-designed detonation wave regulator was used to control the detonation and cut the shell. It was found that the self-designed regulator controlled the fragment shape. The macrostructure and micro-characteristics of fragments revealed that shear fracture was a prior mechanism, the shell fractured not only at the position of detonation collision, but the crack also penetrated the shell at the first contact position of the Chapmen-Jouguet (C-J) wave. The effects of groove number and outer layer thickness on the fracture behavior were tested by simulations. When the thickness of the outer layer was 5–18 mm, it has little effect on fragmentation of the shell, and shells all fractured at similar positions. The increase of the groove number reduced the fracture possibility of the first contact position of the C-J wave. When the groove number reached 7 with a 10 mm outer layer (1/4 model), the fracture only occurred at the position of detonation collision and the fragment width rebounded.     

爆轰波斜冲击作用下破片飞散特性研究

为研究非对称结构战斗部的破片飞散特性,利用斜激波理论对爆轰波作用于壳体表面的过程进行研究,并利用自由面速度倍增定律对波在自由面反射后质点速度的计算进行简化,得到了破片飞散角的计算模型。利用D型战斗部试验数据对计算模型进行验证,结果表明,斜激波理论计算得到的破片飞散与试验结果吻合很好;当入射角较小时,壳体飞散角与入射角成线性关系。     

Application of Two-dimensional Viscous CE/SE Method in Calculation of Two-phase Detonation

The method of two-dimensional viscous space-time conservation element and solution element (CE/SE) can be used to calculate the gas-liquid two-phase interior flow field in pulse detonation engine (PDE). In this paper, the evolution of the detonation wave and the distribution of its physical parameters were analyzed. The numerical results show that the change of axial velocity of gas is the same as that of detonation pressure. The larger the liquid droplet radius is, the longer the time to get stable detonation wave is. The calculated results coincide with the experimented results better.     

Study of simple plane wave generator with an air-metal barrier

Plane wave generators (PWGs) are used to accelerate flyer plates to high velocities with their generated plane waves, which are widely used in the test of dynamic properties of materials. The traditional PWG is composed of two explosives with different detonation velocities. It is difficult to implement the related fabrication processes and control the generated waves due to its complicated structures. A simple plane wave generator is presented in this paper, which is composed of two identical cylindrical high explosive (HE) charges and an air-metal barrier. A theoretical model was established based on two different paths of the propagation of detonation waves, based on which the size of air-metal barrier was calculated for a given charge. The corresponding numerical simulations were also carried out by AUTODYN-2D^® based on the calculated results, which were used to compare with the theoretical calculations. A detonation wave with a flatness of 0.039 μs within the range of 70-percent diameter of the main charge was obtained through the simulations.     

燃气发生器低频非稳态燃烧统计分析

针对冲压发动机地面试验需求,设计燃气发生器,通过试验统计研究其燃烧稳定性特征。结果表明:该燃气发生器发生低频非稳态燃烧的概率为32.7%,存在两种振荡形态。一种存在振荡主频,即低频不稳定燃烧;另一种没有主频,燃烧形态为粗暴燃烧。粗暴燃烧发生概率高且与余氧系数存在较强的相关性,低频不稳定燃烧发生概率低。两种形态的振荡能量分布位置不同。     

气液比对液体中心式气液同轴离心喷嘴燃烧过程的影响

为了分析气液比对液体中心式气液同轴离心喷嘴燃烧过程的影响,针对一台采用液体中心式气液同轴离心喷嘴的燃气发生器在不同气液比下进行热试,并对试验结果进行深入分析。结果表明:随着气液比的增加,燃烧过程存在三种状态——稳定燃烧、稳定燃烧过渡到低频不稳定燃烧、低频不稳定燃烧。这种低频不稳定燃烧与供应系统的振荡无关,是由气液比增加造成三岔火焰远离喷注面板,当三岔火焰到达喷雾撞击点后火焰稳定性降低,使得火焰在回流区内前后振荡引起的。     

模拟油罐油气混合物爆炸实验与数值仿真研究

对模拟油罐内油气混合物爆炸冲击波特性进行了研究.在直径为1 m的模拟油罐中进行了油气混合物爆炸模拟实验,建立了模拟油罐油气混合物爆炸的数值仿真模型,并借助大型商业软件Fluent6.2完成了数值仿真研究.数值仿真结果与实验值较为吻合.模拟实验和数值仿真研究的结果表明:油气体积分数、罐内初始温度等决定模拟油罐油气混合物爆炸压力的大小.油罐内爆炸压力波的振荡特性对金属油罐结构来说是有害的.