燃烧室压力对潜入式喷管喉衬热应力的影响

为了研究燃烧室压力对固体火箭发动机潜入式喷管热应力影响规律的问题,采用商业流体软件,基于压力求解器,求解了喷管纯气相的流场,确定了燃气温度、压力、壁面对流换热系数;采用有限元软件,依据流场计算的非均布壁面压力与非均布对流换热,求解了燃烧室压力为6 MPa下的潜入式喷管热结构问题;通过地面点火试验验证了仿真模型与数值方法的有效性与准确性;采用相同计算模型与数值方法,求解了在燃烧室压力为9 MPa、12 MPa下的喷管热结构问题,揭示了燃烧室压力对喉衬热应力的影响规律。结果表明:整个工作过程,喉衬环向应力最大值为103.9 MPa,位于内表面,且随时间增大,先增大后减小;喉衬环向拉应力也随时间先增大后减小;随压力增大,对流换热系数增大,喉衬温度升高,喉衬环向拉应力增大,喉衬环向压应力减小。     

燃烧室前缘扩张角对旋转爆震冲压发动机的影响

针对圆柱形隔离段-燃烧室构型的旋转爆震冲压发动机,开展了总温为860 K、马赫数为2的来流条件下的直连式试验,探讨了燃烧室前缘扩张角(θ=30°,45°,60°,90°)对爆震波传播特性、工况范围及压力分布的影响。结果表明:当燃烧室前缘扩张角为90°时,燃烧模态均为爆燃燃烧;随着扩张角的减小,燃烧模态将会向锯齿波和混合模态(包含单波阶段)转换。当燃烧室前缘扩张角为30°时,旋转爆震的自持工况范围最宽且燃烧室压力最高;同时,随着燃烧室前缘扩张角减小,实现混合模态的当量比下限降低。此外,分析了燃烧模态对来流的影响,发现:锯齿波/混合模态燃烧室内存在的周期性高频压力扰动会使隔离段内的激波串位置前移;混合模态对超声速来流的影响最为显著。     

流量连续可调火箭发动机极度富燃燃烧特性

以气氧/煤油作为推进剂对火箭发动机进行流量连续调节试验,研究火箭发动机连续变工况过程中的燃烧特性。火箭发动机通过可调气蚀文氏管连续调节煤油流量。试验在富燃工况(混合比0.405~0.690)下成功点火,并实现了混合比、燃气总流量连续调节。试验发现流量连续调节过程中,当混合比小于0.535时,燃烧室压力随煤油流量减小而增大;当混合比大于0.535时,燃烧室压力随煤油流量减小而减小。同时,特征速度和燃烧效率随混合比增大而增大,并且混合比小于0.535时特征速度、燃烧效率增大的速率大于混合比大于0.535时的速率。研究表明推进剂流量与燃烧效率同时影响燃烧室压力。当混合比小于0.535时,燃烧效率的影响占优;混合比大于0.535时,推进剂流量影响占优。     

Mg／PTFE／添加剂红外诱饵剂的红外辐射性能研究

研究了Mg／PTFE／添加剂红外诱饵剂的压药直径和压药密度对红外辐射性能的影响。在同一种配方下,经过试验发现辐射强度同质量燃烧速度成线性关系;辐射强度随着压药密度的增加而减小,最后趋于稳定;有效辐射率随着压药密度和压药直径的改变变化不大,表明压药密度和压药直径对有效辐射率基本没有影响。     

超燃冲压发动机燃烧室构型优化的试验研究

在直连式超燃冲压发动机试验系统上,通过调节超燃冲压发动机燃烧室壁面扩张角和燃料喷注位置,对燃烧室构型优化进行了试验研究。为了提高试验效率,燃烧室形面调节采用正交试验设计方法进行组织,每个形面进行5种喷注位置的试验,每次试验通过文氏管调节3个当量比的燃料流量。利用试验数据构造燃烧室性能关于构型参数的响应面模型,可用于燃烧室构型优化。通过两次渐进优化获得了性能更优的燃烧室构型,并根据试验数据分析了各构型参数对燃烧室性能的影响,结果表明:优化构型燃烧室的推力增益比基准构型增大了10.4%;燃烧室性能受各构型参数的强烈耦合影响。     

气氧甲烷溅板式层板喷注器燃烧特性试验分析

采用试验方法分别对单喷嘴和多喷嘴溅板式层板喷注器燃烧特性进行研究,考察不同工况下喷注器面板热载情况,得到不同混合比、不同结构参数对燃烧室压力分布和燃烧效率的影响规律。试验结果表明:混合比对多喷嘴喷注器燃烧室压力影响不大,但对燃烧效率有较大影响。对于单喷嘴喷注器,燃烧效率随着混合比的增加而增高。相同条件下,增大扩张角及出口层宽度有利于提高喷注器燃烧效率,但会引起喷注面板热载增大,各喷注器喷注面板均产生不同程度的变形或失效。该结果对于正确指导层板式喷注器的设计以及筛选喷注器结构具有重要意义。     

线性可调音速喷嘴工作特性仿真

为了满足组合发动机模态转换的要求,连续稳定调节推进剂流量十分关键。为此,针对气体推进剂,在常规音速喷嘴的基础上设计了一种可调音速喷嘴。通过塞锥改变音速喷嘴的节流面积,进而实现流量的连续调节。采用两次包络线方法设计塞锥型面,使得可调音速喷嘴具有线性的流量特性。采用计算流体动力学数值仿真研究可调音速喷嘴的工作特性。仿真结果表明反压小于临界反压时,可调音速喷嘴流量不受反压影响。可调音速喷嘴保持临界状态的临界反压比随流量的减小呈增大的趋势。线性可调音速喷嘴的流量与塞锥位置有较好的线性关系,其流量系数高且几乎不受塞锥位置的影响。     

数值模拟气液针栓式火箭发动机喷雾燃烧对声学激励的响应

为研究气液针栓式火箭发动机的声学振荡特性并为其优化设计提供指导,加工了具有矩形燃烧室的LOX/GCH₄针栓式发动机,采用Euler-Lagrange方法仿真横向速度扰动产生的声学响应,以期在热试前了解声学激励频率对非稳态喷雾燃烧过程的影响。仿真结果表明,采用的横向速度扰动能在燃烧室内产生同频率的一阶横向声学振荡响应。喷雾燃烧对声学激励的响应强弱受扰动频率与燃烧室一阶横向振荡模态固有频率的相对大小影响较大。当扰动频率与该固有频率相等时,压力和燃烧释热随速度扰动出现同相振荡,压力振荡幅值显著增高导致燃烧室前半段的喷雾和火焰同步摆动;同时,燃烧室内存在扩散燃烧变为预混燃烧的趋势,甲烷在更短的距离内燃烧完全且燃烧室温度趋于均匀。     

自重湿陷性黄土的力学特性试验研究

对宁夏扶贫扬黄灌溉工程十一号泵站地基的原状自重湿陷性黄土进行了系统的非饱和土试验研究,包括土水特征曲线试验、直剪试验、各向同性三轴压缩试验和控制吸力的三轴湿陷试验.试验结果表明:吸力不超过200 kPa时,原状土的持水能力高于重塑土,当吸力超过200 kPa后,两种土的土水特征曲线相接近;原状黄土的内摩擦角随吸力基本不变,总粘聚力随吸力的增加而线性增加;不同吸力下的屈服净平均应力随着吸力的增大而增大,屈服后的压缩指数随吸力增大而减小;同一净围压和偏应力下,随吸力的增加湿陷变形增加;净围压对湿陷变形有一定影响.     

基于GT-Suite的冷却液流量对柴油机性能的影响研究

针对目前大部分船用柴油机冷却系统存在的冷却过度问题,建立了柴油机工作过程-燃烧室-冷却系统耦合仿真模型.与单纯的柴油机冷却系统仿真模型相比,耦合仿真模型考虑了缸内燃烧放热与燃烧室壁面 、燃烧室壁面与冷却系统的双向传热影响,仿真计算过程与实机运行状态更加贴近,试验证明了耦合仿真模型的精确性.基于仿真模型,计算分析了柴油机...     

模型三组元喷嘴雾化SMD变化规律

为了充分研究新型三组元喷嘴的内混腔雾化特性 ,设计了模型喷嘴进行多工况试验。试验发现 ,维持气体或液体压降不变 ,改变另一种介质的压降 ,会得到不同的雾化平均直径随气体压降或液体压降 ,以及气液比ALR的变化曲线 ,这些曲线有着明显的规律。大量试验表明 ,虽然平均直径SMD随气体压降或液体压降的变化曲线明显不同 ,但其随气液比的变化规律却趋于相同     

Experiment and simulation of launching process of a small-diameter steel cartridge case

In order to explore the rules of the deformation force during the launching of a small-diameter steel cartridge, the semi-closed bomb test method is used to test the greatest strains on chamber outer wall under the different chamber pressures. The pressure curves of cartridge chamber are measured in experiment, and the tensile test data of cartridge are loaded into the numerical calculation to compare with the experimental data. The conclusion was obtained that the calculated results match better with the experimental results by considering strain rate bilinear kinematic hardening material constitutive model. The forces on the various parts of the cartridge during launching and their deformation rules are achieved, in which the equivalent plastic strain decreases and the cylinder ring withstands the maximum equivalent stress when the cartridge case clings to the bore from the mouth to the bottom.     

基于最小二乘支持向量机的坦克炮身管剩余寿命预测方法

针对高膛压坦克炮身管剩余寿命预测的难题,结合坦克实弹射击试验数据量少和非线性的特点,基于最小二乘支持向量机构建了坦克炮身管剩余寿命预测模型,给出了模型参数的选取方法,并以某型坦克炮射击试验为基础,对坦克炮身管剩余寿命预测模型进行了验证。结果表明:该模型预测坦克炮身管剩余寿命效果良好。     

Supercritical carbon dioxide as a new working medium for pneumatic launch: A theoretical study

Compared with the conventionally gaseous or liquid working media, the specific internal energy of supercritical carbon dioxide (SCD) is higher at the same temperature and pressure, and the critical temperature of carbon dioxide is close to room temperature, making SCD a potential new working medium for pneumatic launch. To analyze the feasibility of this conception, an analytical model of a pneumatic catapult is established on basis of the conservations of mass and energy. The model consists of a high-pressure chamber and a low-pressure chamber connected by multiple valves, and there is a movable piston in the low-pressure chamber that can push an aircraft to accelerate. The effects of the launch readiness state of SCD in the high-pressure chamber, the initial volume of the low-pressure chamber and the valve control on the movement of the aircraft are analyzed. It is found that there is a restrictive relation between the temperature and pressure of the launch readiness state of SCD, i.e., there is a maximum allowable launch readiness pressure when the launch readiness temperature is fixed. If this restrictive relation is not satisfied, the working medium in the low-pressure chamber will drop to its triple point within a few milliseconds, leading to a launch failure. Owing to this restrictive relation, there is an optimal launch readiness state of SCD with the highest working capacity for any allowable launch readiness temperature. The pressure of the low-pressure chamber will decrease significantly as the initial volume increases, leading to a decreased acceleration of the aircraft. The ac-celeration can be controlled below a critical value by a designed sequential blasting technique of multiple valves. The calculated results show that a 500 kg aircraft can be accelerated from 0 to 58 m/s in 0.9 s with 36 kg of carbon dioxide. This research provides a new technique for the controllable cold launch of an aircraft.     

Pressure relief of underground ammunition storage under missile accidental ignition

Safety of underground ammunition storage is an important issue, especially during the accidental ignition of missiles. This work investigates the pressure and temperature distribution of the multi-layer underground ammunition storage with a pressure relief duct during the accidental ignition process of the missile. A large-scale experiment was carried out using a multi-layered restricted space with a pressure relief duct to simulate the underground ammunition store and a solid rocket motor to simulate the accidental ignition of the missile. The results show that when the motor gas mass flow increased by 5.6 times, the maximum pressure of the ammunition storage increased by 5.87 times. At a certain motor flow rate, when the pressure relief exhaust area at the end of the relief duct was reduced by 1/2, the maximum pressure on the first layer did not change. But the rate of pressure relief was reduced and the time delayed for the pressure of ammunition store to drop to zero. In this experiment, when the motor ignition position was located in to the third layer ammunition chamber, the maximum pressure was reduced by 32.9％ and also reduced the rate of change of pressure. In addition, for the experimental conditions, the theoretical analysis of the pressure relief of the ammunition storage is given by a simplified model. Based on the findings, some suggestions to the safety protection design of ammunition store are proposed.     

模拟海深条件下提升阀流动特性的实验研究

水压传动技术应用于深海环境可以直接从海洋中吸水加压,高压水作功之后可以直接排入海洋,不需要水箱和回水管道,大大简化了系统,具有独特的优势。然而,在深海作业时,液压元件的工况同陆地相比有较大的差异,海深压力相当于在元件出口加了一个背压。文中用背压来模拟海水压力,对以水作介质时背压对提升阀口流量特性的影响进行了实验研究。研究结果表明,背压使得流量饱和更容易发生;有背压时的流量系数比没有背压时的流量系数大;当阀芯和阀座有叠合时,背压对阀口流量特性的影响比阀芯和阀座没有叠合时的影响大。     

二维可压缩流动抽吸流量模型及验证

根据超声速与亚声速流动的特征,依据Prandtl-Meyer膨胀波理论,根据背压与来流静压确定膨胀波后的马赫数,获得了质量抽吸流率,并导出了壅塞发生的条件,建立了二维超声速抽吸模型;根据冲量定理,假定气体从主流区域到抽吸腔流态的变化是由于压差的冲量作用,建立了亚声速抽吸模型,并且进一步阐述了亚声速抽吸壅塞发生的机制。计算流体力学验证表明亚声速抽吸冲量模型的偏差较大,因此通过数值拟合模型来描述亚声速抽吸流动。该研究为三维抽吸研究提供了参考。     

天然气在土壤中泄漏的稳态温度场分析

埋地高压天然气经小孔泄漏会导致土壤冻结形成冻土,应用一元气体动力学、流体力学和传热学知识建立了天然气小孔泄漏吸热率模型和土壤稳态温度场模型,并进行了实例计算。结果表明：当天然气输送压力小于临界压力,小孔泄漏吸热率随压力的增大而增大;当天然气输送压力大于等于临界压力,小孔泄漏吸热率达到最大值;冻土厚度随土壤热导率或空气对流传热系数的增大而减小,但土壤热导率对其影响较小,空气对流传热系数对其影响较大。     

气—固两相自由射流的粒子仿真方法

采用粒子仿真方法直接跟踪颗粒相运动轨迹,采用NND格式求解NS方程,数值模拟了气-固两相自由射流流场.计算结果表明,将粒子仿真与CFD方法相结合是研究气-固两相流动问题的有效途径.颗粒相参数变化将对气体流场产生一定影响.