The properties of Sn–Zn–Al–La fusible alloy for mitigation devices of solid propellant rocket motors

The Al and La elements are added to the Sn9Zn alloy to obtain the fusible alloy for the mitigation devices of solid propellant rocket motors. Differential scanning calorimetry (DSC), metallographic analysis, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), tensile testing and fracture analysis were used to study the effect of Al and La elements on the microstructure, melting characteristics, and mechanical properties of the Sn9Zn alloy. Whether the fusible diaphragm can effectively relieve pressure was investigated by the hydrostatic pressure at high-temperature test. Experimental results show that the melting point of the Sn9Zn-0.8Al0·2La and Sn9Zn–3Al0·2La fusible alloys can meet the predetermined working temperature of ventilation. The mechanical properties of those are more than 35% higher than that of the Sn9Zn alloy at −50 °C–70 °C, and the mechanical strength is reduced by 80% at 175 °C. It is proven by the hydrostatic pressure at high-temperature test that the fusible diaphragm can relieve pressure effectively and can be used for the design of the mitigation devices of solid propellant rocket motors.     

Effect of bending temperatures on the microstructure and springback of a TRIP steel sheet

Transformation-induced plasticity (TRIP) steel possesses high strength and formability, enabling the use of a thinner gauge material and allowing for the fabrication of complex shapes. In this research, we measured the effect of bending temperatures on the microstructure and air-bending springback angle of TRIP steel at temperatures from 25 to 600 °C. Real-time in situ X-ray diffraction and scanning electron microscopy were used for pre- and postbending analysis. As the prebending temperature increased from 25 °C to 600 °C, the retained austenite (RA) volume fraction decreased, and the RA transformed to bainite at temperatures above 400 °C. The springback angle was positively correlated with the prebending RA volume fraction, with the smallest springback angle achieved at 400 °C. Additionally, the springback angle was positively correlated with the bending angle, because the RA transformation ratio contributed to increased strain hardening. Further microstructure analysis revealed that the RA became elongated in the tension direction as the bending temperatures increased.     

Neural network modeling to evaluate the dynamic flow stress of high strength armor steels under high strain rate compression

An artificial neural network (ANN) constitutive model is developed for high strength armor steel tempered at 500 °C, 600 °C and 650 °C based on high strain rate data generated from split Hopkinson pressure bar (SHPB) experiments. A new neural network configuration consisting of both training and validation is effectively employed to predict flow stress. Tempering temperature, strain rate and strain are considered as inputs, whereas flow stress is taken as output of the neural network. A comparative study on Johnson–Cook (J–C) model and neural network model is performed. It was observed that the developed neural network model could predict flow stress under various strain rates and tempering temperatures. The experimental stress–strain data obtained from high strain rate compression tests using SHPB, over a range of tempering temperatures (500–650 °C), strains (0.05–0.2) and strain rates (1000–5500/s) are employed to formulate J–C model to predict the high strain rate deformation behavior of high strength armor steels. The J-C model and the back-propagation ANN model were developed to predict the high strain rate deformation behavior of high strength armor steel and their predictability is evaluated in terms of correlation coefficient (R) and average absolute relative error (AARE). R and AARE for the J–C model are found to be 0.7461 and 27.624%, respectively, while R and AARE for the ANN model are 0.9995 and 2.58%, respectively. It was observed that the predictions by ANN model are in consistence with the experimental data for all tempering temperatures.     

Tuning the reactivity of Al–Ni by fine coating of halogen-containing energetic composites

In this paper, various core-shell structured Al–Ni@ECs composites have been prepared by a spray-drying technique. The involved ECs refer to the energetic composites (ECs) of ammonium perchlorate/nitrocellulose (AP/NC, NA) and polyvinylidene fluoride/hexanitrohexaazaisowurtzitane (PVDF/CL-20, PC). Two Al–Ni mixtures were prepared at atomic ratios of 1:1 and 1:3 and named as Al/Ni and Al/3Ni, respectively. The thermal reactivity and combustion behaviors of Al–Ni@ECs composites have been comprehensively investigated. Results showed that the reactivity and combustion performance of Al–Ni could be enhanced by introducing both NA and PC energetic composites. Among which the Al/Ni@NA composite exhibited higher reactivity and improved combustion performance. The measured flame propagation rate (v = 20.6 mm/s), average combustion wave temperature (T_max = 1567.0 °C) and maximum temperature rise rate (γ_t = 1633.6 °C/s) of Al/Ni@NA are higher than that of the Al/Ni (v = 15.8 mm/s, T_max = 858.0 °C, and γ_t = 143.5 °C/s). The enhancement in combustion properties could be due to presence of the acidic gaseous products from ECs, which could etch the Al₂O₃ shell on the surface of Al particles, and make the inner active Al to be easier transported, so that an intimate and faster intermetallic reaction between Al and Ni would be realized. Furthermore, the morphologies and chemical compositions of the condensed combustion products (CCPs) of Al–Ni@ECs composites were found to be different depending on the types of ECs. The compositions of CCPs are dominated with the Al–Ni intermetallics, combining with a trace amount of Al₅O₆N and Al₂O₃.     

Cell-type continuous electromagnetic radiation system generating millimeter waves for active denial system applications

The cell-type continuous electromagnetic radiation system is a demonstration device capable of generating high-power millimeter electromagnetic waves of a specific wavelength and observing their effects on living organisms. It irradiates a biological sample placed in a 30 × 30 × 50 cm³ cell with electromagnetic waves in the 3.15-mm-wavelength region (with an output of ≥1 W) and analyzes the temperature change of the sample. A vacuum electronic device-based coupled-cavity backward-wave oscillator converts the electron energy of the electron beam into radiofrequency (RF) energy and radiates it to the target through an antenna, increasing the temperature through the absorption of RF energy in the skin. The system causes pain and ultimately reduces combat power. A cell-type continuous electromagnetic radiation system consisting of four parts—an electromagnetic-wave generator, a high-voltage power supply, a test cell, and a system controller—generates an RF signal of ≥1 W in a continuous waveform at a 95-GHz center frequency, as well as a chemical solution with a dielectric constant similar to that of the skin of a living organism. An increase of 5 °C lasting approximately 10 s was confirmed through an experiment.     

Burning characteristics of high density foamed GAP/CL-20 propellants

The monolithic foamed propellants with high densities were prepared by casting and two-step foaming processes. Glycidyl azide polymer (GAP) and isocyanate were used as the binder system and 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (HNIW, CL-20) was employed as the energetic component. The newly designed formulation containing 60 % CL-20 produced a force constant of 1077 J/g and low flame temperature of 2817 K. Two foamed propellants with densities of 1.32 g/cm³ and 1.53 g/cm³ were fabricated by a confined foaming process and examined by closed bomb tests. The results revealed that porosity significantly affects burning performance. A size effect on combustion behaviors was observed for the foamed propellant with 5.56 % porosity, and a double-hump progressive dynamic vivacity curve was obtained. At last, the 30 mm gun test was carried out to demonstrate the interior ballistic performance, and the muzzle velocity increased by 120 m/s at the same maximum chamber pressure when monolithic propellant was added in the charge.     

Scale-up synthesis and characterization of 2,6-diamino-3,5-dinitropyrazine-1-oxide

2,6-diamino-3,5-dinitropyrazine-1-oxide (ANPZO), as an insensitive high explosive, with a high yield and excellent purity has been prepared at pilot plant scale by an improved method. The synthesized ANPZO is characterized by IR, laser granularity measurement, SEM and HPLC. The particle analysis revealed that the improved method could offer desired product with average particle size of 40 μm and high purity (>98.45%). The experimental parameters exhibited that the detonation velocity of the formulation based on ANPZO was higher than that of the corresponding TATB formulation. The DSC curve showed that the exothermic decomposition of the product occurred at the temperature between 300.5 °C and 360.4 °C. Furthermore, the sensitivity test suggests its safe nature towards mechanical stimulus.     

Novel aluminum-based fuel: Facile preparation to improve thermal reactions

To improve the thermal properties of aluminum (Al) in the energetic system, a coated structure with ammonium perchlorate (AP) was prepared by a facile approach. And N, N-Dimethylformamide (DMF) was chosen as an ideal solvent based on heterogeneous nucleation theory and molecular dynamics simulation. This coated structure could enlarge the contact area and improve the reaction environment to enhance the thermal properties. The addition of AP could accelerate oxidation temperature of Al with around 17.5 °C. And the heat release of 85@15 composition rises to 26.13 kJ/g and the reaction degree is 97.6% with higher peak pressure (254.6 kPa) and rise rate (1.397 MPa/s). An ideal ratio with 15 wt% AP was probed primarily. The high energy laser-induced shockwave experiment was utilized to simulate the reaction behavior in hot field. And the larger activated mixture of coated powder could release more energy to promote the growth of shockwave with higher speed up to 518.7 ± 55.9 m/s. In conclusion, 85@15 composition is expected to be applied in energetic system as a novel metal fuel.     

Insensitive energetic microspheres DAAF/RDX fabricated by facile molecular self-assembly

Insensitive energetic materials are promising in the defense weapons field. However, energetic materials still suffer from great challenges and the concern about their safety limits their utilization. In this work, insensitive energetic explosive 3,3′-diamino-4,4′-azoxyfurazan/hexahydro-1,3,5-trinitro-1,3,5-triazine (DAAF/RDX) microspheres were fabricated by self-assembly method. Rod-like DAAF/RDX was prepared by mechanical ball milling for comparison. DAAF/RDX composites with different mass ratios (90:10, 80:20, and 70:30) were obtained. The morphologies and structures of as-obtained DAAF/RDX composites were characterized by scanning electron microscopy (SEM), powder x-ray diffraction (PXRD) and fourier transform infrared spectroscopy (FT-IR). The results showed that DAAF/RDX microspheres exhibited regular shaped microspheres with sizes from 0.5 to 1.2 μm. There was no crystal transition during the modification process. The thermal properties of as-obtained materials were then evaluated by differential scanning calorimetry (DSC) and materials studio software. DAAF/RDX microspheres showed an advanced decomposition peak temperature compared with rod-like DAAF/RDX. The binding energy and peak temperature values at zero β_i (T_P0) of DAAF/RDX (90:10) increased by 36.77 kJ/mol, 1.6 °C, and 58.11 kJ/mol, 12.3 °C compared to DAAF/RDX (80:20) and DAAF/RDX (70:30), indicating the better thermal stability of DAAF/RDX (90:10). The characteristic drop height (H₅₀) of DAAF/RDX (higher than 100 cm) composites was higher than that of raw RDX (25 cm), suggesting significant improvements in mechanical safety. The preparation of DAAF/RDX microspheres is promising for the desensitization of RDX and useful for the formation of other materials and future wide applications.     

Low velocity impact studies of E-glass/epoxy composite laminates at different thicknesses and temperatures

Low velocity impact experiments were carried out on E-glass/epoxy composite laminates having varying thicknesses at sub zero and elevated temperatures using hemi spherical steel impactor of 16 mm diameter with impact energies in the rage of 50–150 J. The performance of the laminates was assessed in terms of energy absorption, maximum displacement, peak force and failure behaviour. Results indicated that the effect of temperature on energy absorption of the laminate is negligible although the laminates are embrittling at sub zero temperatures. However it has influence on failure behaviour and displacement. Peak force has increased linearly with increase in laminate thickness from 5 to 10 mm. However it got reduced by 25% when temperature was increased from −20 °C to 100 °C. Based on experimental results, laminate perforation energies were predicted using curve fitting equations. Statistical analysis was carried out using Taguchi method to identify the global effects of various parameters on laminate performance and confirmed that the laminate thickness has significant influence as compared to temperature, for the studied range.     

Research on the influences of confining pressure and strain rate on NEPE propellant: Experimental assessment and constitutive model

In order to study the influences of confining pressure and strain rate on the mechanical properties of the Nitrate Ester Plasticized Polyether (NEPE) propellant, uniaxial tensile tests were conducted using the self-made confining pressure system and material testing machine. The stress-strain responses of the NEPE propellant under different confining pressure conditions and strain rates were obtained and analyzed. The results show that confining pressure and strain rate have a remarkably influence on the mechanical responses of the NEPE propellant. As confining pressure increases (from 0 to 5.4 MPa), the maximum tensile stress and ultimate strain increase gradually. With the coupled effects of confining pressure and strain rate, the value of the maximum tensile stress and ultimate strain at 5.4 MPa and 0.0667 s⁻¹ is 2.03 times and 2.19 times of their values under 0 MPa and 0.00333 s⁻¹, respectively. Afterwards, the influence mechanism of confining pressure on the NEPE propellant was analyzed. Finally, based on the viscoelastic theory and continuous damage theory, a nonlinear constitutive model considering confining pressure and strain rate was developed. The damage was considered to be rate-dependent and pressure-dependent. The constitutive model was validated by comparing experimental data with predictions of the constitutive model. The whole maximum stress errors of the model predictions are lower than 4% and the corresponding strain errors are lower than 7%. The results show that confining pressure can suppress the damage initiation and evolution of the NEPE propellant and the nonlinear constitutive model can describe the mechanical responses of the NEPE propellant under various confining pressure conditions and strain rates. This research can lay a theoretical foundation for analyzing the structural integrity of propellant grain accurately under working pressure loading.     

Effect of Drying on Particle Size and Sensitivities of Nano hexahydro-1,3,5-trinitro-1,3,5-triazine

Nano hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) was prepared using a bi-directional rotation mill and dried under different conditions (liquid, temperature and drying). It shows that the samples cake seriously and the particles grow up obviously by ordinary drying in different liquids at 70 °C, which occurs again after vacuum drying. With the increase of temperature, the degrees of caking and aggregation are enhanced. Well dispersed sample maintaining constant particle size is extracted by supercritical drying, especially freeze drying. Furthermore, the mechanical sensitivities of I-RDX, O-RDX and F-RDX, of which the average sizes are 88.03 μm, 15.32 μm and 0.16 μm, respectively, are evaluated. Compared with I-RDX, the friction, impact and shock sensitivities of O-RDX are slightly lower. However, the friction, impact and shock sensitivities of F-RDX are reduced by 30%, 99.0% and 59.9%, respectively.     

Phenomenological modelling of flow behaviour of 20MnMoNi55 reactor pressure vessel steel at cryogenic temperature with different strain rates

In the present study a phenomenological constitutive model is developed to describe the flow behaviour of 20MnMoNi55 low carbon reactor pressure vessel (RPV) steel at sub-zero temperature under different strain rates. A set of uniaxial tensile tests is done with the variation of strain rates and temperature ranging from 10⁻⁴ s⁻¹ to 10⁻¹ s⁻¹ and -80 °C to −140 °C respectively. From the experimental data, family of flow curves at different temperatures and strain rates are generated and fitted exponentially. The strain rate and temperature dependence of the coefficients of the exponential flow curves are extracted from these curves and characterised through a general phenomenological constitutive coupled equation. The coefficients of this coupled equation are optimised using genetic algorithm. Finite element simulation of tensile tests at different strain rates and temperatures are done using this coupled equation in material model of Abaqus FEA software and validated with experimental results. The novelties of proposed model are: (a) it can predict precisely the flow behaviour of tensile tests (b) it is a simple form of equation where fitting parameters are both function of strain rate ratio and temperature ratio, (c) it has ability to characterize flow behaviour with decreasing subzero temperatures and increasing strain rates.     

Design of infrared camouflage cloak for underground silos

The temperature difference between the exposed surface of an underground silo and the surrounding soil surface is significant, which means a silo can be easily found by infrared detection. We designed an infrared camouflage cloak consisting of an imitative layer and an insulation layer for the silos. The imitative layer is used to imitate the thermal response of the soil to the surrounding environment. The insulation layer is used to weaken the impact of the internal temperature field of the silo on the lower boundary of the imitative layer. A silo model including surrounding soil and a soil model without silo were established, and the influences of the material and thickness of each layer on the infrared camouflage effect were analyzed. The results show that when using a silicone rubber containing alumina powder with a volume fraction of 3.18% as the imitative material, its thermal inertia is in consistent with that of the soil. Meanwhile, it was found that the thickness of the imitative layer doesn’t need to be greater than its thermal penetration depth to achieve the infrared camouflage, and the absence of the insulation layer will cause hot spots on the silo surface in winter to weaken the camouflage effect. The optimized thicknesses of the imitative layer and the insulation layer are 22 cm and 4 cm respectively. The simulations indicate that with the application of the cloak, the maximum value of the absolute values of the temperature differences between the average temperatures of the silo surface and the surrounding soil surface temperatures drops from 1.59 °C to 0.31 °C in summer and from 1.92 °C to 0.21 °C in winter. This designed cloak can achieve an all-weather and full-time passive infrared camouflage.     

Effects of module number and firing condition on charge thermal safety in gun chamber

Thermal safety of modular charge which is fed into and retained in the chamber after gun fires consecutively is first investigated with cook-off method.A two-dimensional cook-off model of modular charge in gun chamber is established and the cook-off process of modular charge in gun chamber is numerically simulated.Then the effects of module number and firing condition on charge thermal safety are evaluated by researching the cook-off response characteristics of modules.The results show that,under conditions of different module numbers the cook-off responses all occur on the module closest to the boundary of missile,and the single-base propellants located at the inner surface of cartridge ignite first.When the number of loaded module changes from 1 to 6,the cook-off response temperatures vary little,only in a small range of 478.1 K-482.4 K.The cook-off response times decrease logarithmically in the range of 211.2 s-166.7 s with the increasing length of residual air gap in gun chamber.The simulation results are well matched with the experimental data.Furthermore,different firing conditions have great influence on the cook-off response time,minor influence on the initial response position and little in-fluence on the response temperature.Under the three conditions of consecutive 32 launches with 5 rounds/min,43 launches with 1 round/min,and 41 launches with different firing frequencies,the cook-off response temperatures are 479.2 K,481.1 K and 479.9 K respectively and the response times are 709.2 s,211.2 s and 214.4 s respectively.The response position is near the middle area of the inner cartridge surface in the former condition and near the right area in the latter two conditions.     

围压下固体推进剂的破坏机理分析

贴壁浇筑的固体发动机推进剂药柱在点火状态下处于三向围压状态,而环向承受拉应变,亟待对围压下推进剂的破坏机理展开研究。基于自研的围压加载试验系统,通过开展推进剂在不同围压、温度和应变率下的单轴拉伸试验来研究围压、温度和应变率的耦合作用对推进剂力学行为的影响。针对围压下推进剂的力学响应特征,通过细观力学仿真进一步研究围压下推进剂的破坏形式,同时借助电镜扫描试验分析推进剂试样断面的形貌特征,通过试验和仿真相结合的手段分析了围压下推进剂的破坏机理。研究结果表明,围压下推进剂的损伤界面显著减少,且随着围压载荷的逐渐增加,推进剂的损伤形式从以颗粒脱湿为主转变为以颗粒破碎为主。     

Formulation development and characterization of cellulose acetate nitrate based propellants for improved insensitive munitions properties

Cellulose acetate nitrate (CAN) was used as an insensitive energetic binder to improve the insensitive munitions (IM) properties of gun propellants to replace the M1 propellant used in 105 mm artillery charges. CAN contains the energetic nitro groups found in nitrocellulose (NC), but also acetyl functionalities, which lowered the polymer's sensitivity to heat and shock, and therefore improved its IM properties relative to NC. The formulation, development and small-scale characterization testing of several CAN-based propellants were done. The formulations, using insensitive energetic solid fillers and high-nitrogen modifiers in place of nitramine were completed. The small scale characterization testing, such as closed bomb testing, small scale sensitivity, thermal stability, and chemical compatibility were done. The mechanical response of the propellants under high-rate uni-axial compression at, hot, cold, and ambient temperatures were also completed. Critical diameter testing, hot fragment conductive ignition (HFCI) tests were done to evaluate the propellants' responses to thermal and shock stimuli. Utilizing the propellant chemical composition, theoretical predictions of erosivity were completed. All the small scale test results were utilized to down-select the promising CAN based formulations for large scale demonstration testing such as the ballistic performance and fragment impact testing in the 105 mm M67 artillery charge configurations. The test results completed in the small and large scale testing are discussed.     

Numerical and experimental study on the response characteristics of warhead in the fast cook-off process

The response characteristics of the warhead under thermal stimuli conditions are important to the safety improvement. The goal of this study is to obtain data on the warhead in the fast cook-off process. In this paper, a numerical calculation method is proposed, whose reliability is supported by comparison with experimental results. Through the numerical calculation, the temperature distribution, temperature change, and ignition time are acquired. The numerical results show that the ignition time is 76 s after the warhead started to burn and that the maximum temperature of the explosive's outer surface is 238.3 C at the ignition time. The fast cook-off experiment of the warhead is implemented so as to get the flame temperature and reaction grades that are not available through numerical calculation. The experimental results show that the overpressure fails to reach the preset minimum value which is equivalent to 6 kg of TNT and that the reaction grade is deflagration. The research results have reference value for the design of the warhead and the reduction of detonation risks.     

Effects of Mg/PTFE pyrotechnic compositions on reignition characteristics of base bleed propellants and heating mechanism

The effects of magnesium/polytetrafluoroethylene (Mg/PTFE) pyrotechnic compositions on the coupled flow field and reignition mechanism are important aspects governing the performance and range of base bleed projectiles (BBPs).Owing to a decrease in pressure and temperature when the BBP leaves the muzzle,rapid depressurization occurs,which extinguishes the base bleed propellant.The Mg/PTFE py-rotechnic composition pressed in the igniter of the base bleed unit (BBU) provides additional energy to the BBU via a chemical reaction.Thus,the extinguished base bleed propellant is reignited under the effect of high-temperature combustion gas jets from the igniter.In this study,a numerical analysis is conducted to evaluate the effects of PTFE and Mg granularity as well as Mg/PTFE pyrotechnic compo-sitions.Owing to the rapid depressurization,the temperature and pressure was found to decrease for different Mg/PTFE pyrotechnic compositions.However,the depressurization time increased as the PTFE granularity increased,the Mg granularity decreased,and the Mg content increased.When the pressure in the combustion chamber of the BBU decreased to the atmospheric pressure,the combustion gas jets from the igniter expand upstream (rather than downstream).However,these combustion gas jets exhibit different axial and radial expansion characteristics depending on the pyrotechnic compositions used.The results show that the reignition delay time,td,of the base bleed propellant was 377.608,94.27,387.243,523.966,and 221.094 ms for cases A-E,respectively.Therefore,it was concluded that the Mg/PTFE pyrotechnic composition of case B was the most beneficial for the reignition of the base bleed propellant,with the earliest addition of energy and mass to the BBP.