无电焊接材料的燃烧速度和燃烧温度研究

采用高放热性的铝热剂（CuO＋Al）并加入适当的添加剂,制备了便携式的无电焊接笔材料,其燃烧速度可控,且具有高的燃烧温度。研究了反应剂颗粒大小、混料均匀性等对无电焊接笔材料的燃烧性能的影响。结果表明：反应剂粒径对无电焊接笔的燃烧速度具有显著影响,随着反应剂粒径的增大,燃烧速度明显减慢。反应剂粒径和混料时间是影响单位时间放热量和混料均匀度的主要因素,因而对无电焊接笔的燃烧温度具有明显影响。在一定的混料时间下,反应物粉末具有最佳的混料均匀性。反应物粒径小且混料均匀性好的无电焊接笔材料,其燃烧温度高。     

Thermodynamics and performance of Al/CuO nanothermite with different storage time

The storage stability of energetic materials is important for its application. Here, the storage stability of Al/CuO nanothermite, which was prepared by electrospray method and stored with different storage time, was systematically researched. The activation energy of Al/CuO nanothermite was calculated by differential scanning calorimetry (DSC). The ignition temperature and the curve pressure history of Al/CuO nanothermite was measured using ignition temperature measuring device and constant-volume pressurization tests, respectively. Further, the thermites were characterized by X-ray Diffractometer (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM) and Transmission electron microscopy (TEM). The results show that the morphology of the thermites did not change significantly. The activation energy was decreased from 254.1 kJ/mol to 181.8 kJ/mol after storage for 13 months. When stored for 0, 7 and 13 months, the peak pressures of Al/CuO nanothermite were 685.8 kPa, 626.3 kPa and 625.5 kPa, respectively. In addition to the ignition temperature, it was 775 ℃, 739 ℃ and 754 ℃, respectively. This result indicated that the ignition and combustion properties of Al/CuO nano-thermite are obviously reduced when stored for a long time, at room temperature.     

Nanothermite colloids: A new prospective for enhanced performance

Nanothermites (metal oxide/metal) can offer tremendously exothermic self sustained reactions. CuO is one of the most effective oxidizers for naonothermite applications. This study reports on two prospectives for the manufacture of CuO nanoparticles. Colloidal CuO particles of 15 nm particle size were developed using hydrothermal synthesis technique. Multiwalled carbon nanotubes (MWCNTs) with surface are 700 m²/g was employed as a substrate for synthesis of CuO-coated MWCNTs using electroless plating. On the other hand, aluminium particles with combustion heat of 32000 J/g is of interest as high energy density material. The impact of stoichiometric nanothermite particles (CuO/Al & Cuo-coated MWCNTs/Al) on shock wave strength of Al/TNT nanocomposite was evaluated using ballistic mortar test. While CuO-coated MWCNTs decreased the shock wave strength by 15%; colloidal CuO enhanced the shock wave strength by 30%. The superior performance of colloidal CuO particles was correlated to their steric stabilization with employed organic solvent. This is the first time ever to report on fabrication, isolation, and integration of stablilized colloidal nanothermite particles into energetic matrix where intimate mixing between oxidizer and metal fuel could be achieved.     

Thermal and combustion behavior of Al-MnO2 nanothermite with poly(vinylidene fluoride -co- hexafluoropropylene) energetic binder

Fluoropolymers get increasing attention in energetic materials application due to the high fluorine content. To explore the effect of poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) on Al/MnO2 nanothermite, the samples with different contents are prepared and characterized by SEM, TG-DSC, XRD, and their ignition and combustion behavior are tested and recorded. The results show that P(VDF-HFP) as an energetic binder can combine the nanothermite components together, even exist in the gaps. The integrity of energetic materials has been improved. Thermal analysis shows that the addition of P(VDF-HFP) greatly changes the thermal reaction processes, and the exothermic peaks appear early, but the utilization of fuel and oxidizer is not efficient from the XRD results. Furthermore, the appropriate addition of P(VDF-HFP) can directly reduce the ignition energy threshold and increase the combustion time, which is necessary for the potential ignition charge application. The possible reasons for above phenomena are discussed and analyzed. This research provides a reference for improvement of thermite-based ignition charge formulation.     

Effect of metal powders on explosion of fuel-air explosives with delayed secondary igniters

In order to improve the energy level of fuel air explosive(FAE) with delayed secondary igniters, high energetic metal powders were added to liquid fuels mainly composed of ether and isopropyl nitrate. Metal powders' explosive properties and reaction mechanisms in FAE were studied by high-speed video, pressure test system, and infrared thermal imager. The results show that compared with pure liquid fuels, the shock wave overpressure, maximum surface fireball temperature and high temperature duration of the mixture were significantly increased after adding high energetic metal powder. The overpressure values of the liquid-solid mixture at all measuring points were higher than that of the pure liquid fuels. And the maximum temperature of the fireball was up to 1700 ℃, which was higher than that of the pure liquid fuels. After replacing 30％of aluminum powder with boron or magnesium hydride, the shock wave pressure of the mixture was further increased. The high heat of combustion of boron and the hydrogen released by magnesium hydride could effectively increase the blast effect of the mixture. The improvement of the explosion performance of boron was better than magnesium hydride. It shows that adding high energetic metal powder to liquid fuels can effectively improve the explosion performance of FAE.     

X射线衍射仪图谱的定量分析初探

在XD-2型X射线衍射仪分析软件的基础上,制作了Al2O3定量分析所用的内标曲线,并对混合物样品中的物相进行了定量分析,结果和配比值完全一致,说明这种定量分析方法均能运用于多相混合物中物相的定量分析     

Study on Effects of Oxydal on Diesel Engine Combustion

Based on the analysis of the high temperature decomposition of oxydal(H2O2)and the combustion of diesel engine,the effects of H2O2 on the improvement of diesel combustion were studied.An oxydal spray system was designed to inject H2O2/water mixture into the manifold.The experiment was carried out on a 1135 diesel engine bench.The results show that H2O2 injection can make the curve of heat release rate move forward and decrease its peak value.The specific fuel consumption is decreased a little,while both NOx and PM emission are obviously reduced.     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

Fabrication and characterization of Al-CuO nanocomposites prepared by sol-gel method

In this study, Al-CuO nanocomposites were fabricated by sol-gel method. As a contrast, the thermite was prepared by physical mixing at the equivalence ratio of 0.5, 1, 2, respectively. The intermediates and samples as prepared were characterized by SEM and XRD. The exothermic properties of the two samples prepared at different equivalence ratios were tested and the reaction products were characterized by XRD. The SEM results show that the sample prepared by the sol-gel method demonstrates a micron-sized agglomerated sphere formed by a mutual wrapping of Al NPs and CuO NPs, and the particles are evenly distributed in the agglomerate. In addition, when the content of Al powder is seriously insufficient, the heat release of the sample prepared by physical mixing is 1.6 times that of by sol-gel method. With the increase of Al powder content, the exothermic properties of Al/CuO NPs prepared by sol-gel method began to increase significantly compared with physical mixing and the difference is 1.5 times when the equivalence ratio increases to 2. It can be concluded that the reason for this result may be attributed to the different mass transfer modes of components due to the different morphologies of samples.     

添加剂对无电焊接脱渣性及焊缝成形的影响

针对焊接熔渣严重影响无电焊接焊缝成形的问题,通过添加造渣剂组分,研究了添加剂对无电焊接熔渣脱渣性及焊缝成形的影响。测试结果表明:添加剂的加入,使得无电焊接熔渣体系中形成多种多元化合物,并均匀、弥散地分布在Al2O3基体之中,形成规则的片层状组织,具有较好的相容性,而且通过形成多种多元化合物,使得无电焊接熔渣中的Al2O3相含量明显降低,从而显著地改善了无电焊接的脱渣性和焊缝成形性能,焊接接头的拉伸强度得到明显提高。     

High strain rate deformation of explosion-welded Ti6Al4V/pure titanium

Multilayer materials are widely used in military, automobile and aerospace industries. In this paper, the response of an explosion-welded Ti6Al4V/pure titanium with a flat interface to dynamic loading is investigated. An SHPB apparatus is used. Then, the dynamic behaviour of a bimetal sample is explored with a DIC system coupled to the SHPB. Result indicates that in the bimetal sample pure titanium is deformed and failed before Ti6Al4V. The stress curve of the sample shows two different peaks in a striker velocity higher than the 18.3 m/s. When the incident wave encounters the interface of the Ti6Al4V/pure titanium sample, only a small fraction of the wave is reflected owing to similar impedance. Using the direct interpretation stress-strain curve is unreasonable in this case because of unhomogenised plastic deformation. The microstructure of the sample is investigated after loading. An adiabatic shear band is formed in the pure titanium side before failure, and the interface of the sample remains intact under different loading conditions. The FEM simulation result for the sample is in good agreement with experimental observations.     

Ni-Zn铁氧体粉末的溶胶-凝胶合成及微波性能

以硝酸铁、硝酸镍、硝酸锌、柠檬酸和氨水为原料,用溶胶-凝胶法合成了不同组成的Ni-Zn铁氧体粉末。利用热分析、X射线衍射等手段研究了干凝胶热分解行为。利用网络分析仪对铁氧体粉末的电磁性能进行了表征,考察了铁氧体的组成与其电磁性能之间的关系。结果表明,溶胶-凝胶法合成的铁氧体粉末的μ″值随测试频率的提高和Ni-Zn铁氧体中锌含量的增加而减小。     

Tuning the reactivity of Al–Ni by fine coating of halogen-containing energetic composites

In this paper, various core-shell structured Al–Ni@ECs composites have been prepared by a spray-drying technique. The involved ECs refer to the energetic composites (ECs) of ammonium perchlorate/nitrocellulose (AP/NC, NA) and polyvinylidene fluoride/hexanitrohexaazaisowurtzitane (PVDF/CL-20, PC). Two Al–Ni mixtures were prepared at atomic ratios of 1:1 and 1:3 and named as Al/Ni and Al/3Ni, respectively. The thermal reactivity and combustion behaviors of Al–Ni@ECs composites have been comprehensively investigated. Results showed that the reactivity and combustion performance of Al–Ni could be enhanced by introducing both NA and PC energetic composites. Among which the Al/Ni@NA composite exhibited higher reactivity and improved combustion performance. The measured flame propagation rate (v = 20.6 mm/s), average combustion wave temperature (T_max = 1567.0 °C) and maximum temperature rise rate (γ_t = 1633.6 °C/s) of Al/Ni@NA are higher than that of the Al/Ni (v = 15.8 mm/s, T_max = 858.0 °C, and γ_t = 143.5 °C/s). The enhancement in combustion properties could be due to presence of the acidic gaseous products from ECs, which could etch the Al₂O₃ shell on the surface of Al particles, and make the inner active Al to be easier transported, so that an intimate and faster intermetallic reaction between Al and Ni would be realized. Furthermore, the morphologies and chemical compositions of the condensed combustion products (CCPs) of Al–Ni@ECs composites were found to be different depending on the types of ECs. The compositions of CCPs are dominated with the Al–Ni intermetallics, combining with a trace amount of Al₅O₆N and Al₂O₃.     

Light weight HTPB-clay nanocomposites(HCN)with enhanced ablation performance as inhibition materials for composite propellant

In the present study,organically modified Montmorillonite clay with polar moiety,the Cloisite 30B,is used for preparation of Hydroxyl terminated polybutadiene(HTPB)-clay nanocomposites(HCN)by dispersion of nanoclay in polymer matrix under high shear mixing.The nanocomposites thus prepared are evaluated in composite propellants as inhibitor material for their functional utility.Several inhibition formulations containing 5 wt％-15 wt％of nanoclay,with or without the conventional filler Sb2O3,were prepared.All these formulations were evaluated for their physical,mechanical,thermal,and ablative properties.Ablation rate and density of the compositions containing Cloisite 30B is around 23％and 5％lower respectively in comparison of the base composition.Strain capability of these compositions is twofold higher than that of base composition.These compositions have also been evaluated for their smoke generation tendency by measuring infra red(IR)attenuation in the wavelength range 1.3 μm-5.6 μm and 8 μm-13 μm and thereby compared with the base composition.The corresponding results confirmed that the compositions containing Cloisite 30B as filler have much lower IR attenuation than compositions with conventional filler,Sb2O3.Replacement of 5％Sb2O3 by nanoclay showed 8％reduction in IR attenuation rate which further reduced to 16％on replacement of 15％of Sb2O3.Interfacial bonding of HCN based inhibitors is also comparable or even better than conventional inhibitors.Precisely,the nanoclay composites with Cloisite 30B as filler exhibit all desirable properties of an inhibitor.     

Reaction characteristic of PTFE/Al/Cu/Pb composites and application in shaped charge liner

In this paper, the reaction characteristic and its application in shaped charge warhead of a novel reactive material, which introduced copper (Cu) and plumbum (Pb) into traditional polytetrafluoroethylene/aluminum (PTFE/Al), are studied. The thermal analysis and chemical reaction behavior of the PTFE/Al/Cu/Pb mixture are investigated by Differential Scanning Calorimetry (DSC),Thermo-gravimetry (TG), and X-ray Diffraction (XRD) techniques. Then, the shaped charge liners with PTFE/Al/Cu/Pb reactive materials are fabricated, and the X-ray experiments show that they could form reactive jets with excellent performance under the detonation effects of the shaped charge. Based on that, the penetration experiments of shaped charge with PTFE/Al/Cu/Pb reactive liner against steel plates are carried out, and the results demonstrate that the PTFE/Al/Cu/Pb reactive jets could produce a deeper penetration depth compared to the traditional PTFE/Al reactive jets. Meanwhile, the PTFE/Al/Cu/Pb reactive jets also show significant inner-blast effects, leading to dramatically cracking or fragmentation behavior of the penetrated steel plates. This new PTFE/Al/Cu/Pb reactive liner shaped charge presents enhanced penetration behavior for steel targets that incorporates the penetration capability of a high-density and ductility jet, and the chemical energy release of PTFE-matrix reactive materials.     

The effect of al particle size on thermal decomposition,mechanical strength and sensitivity of Al/ZrH2/PTFE composite

To study the thermal decomposition of Al/ZrH2/PTFE with different Al particle size as well as mechanical strength and impact sensitivity under medium and low strain rates, molding-vacuum sintering was adopted to prepare four groups of power materials and cylindrical specimens with different Al particle size. The active decomposition temperature of ZrH2 was obtained by TG-DSC, and the quasi-static me-chanics/reaction characteristics as well as the impact sensitivity of the specimen were studied respec-tively by quasi-static compression and drop-hammer test. The results show that the yield strength of the material decreased with the increase of the Al particle size, while the compressive strength, failure strain and toughness increased first and then decreased, which reached the maximum values of 116.61 MPa, 191％, and 119.9 MJ/m respectively when the Al particle size is 12—14μm because of particle size grading. The specimens with the highest strength and toughness formed circumferential open cracks and reacted partly when pressed. Those with developmental cracks formed inside did not react. It is considered that fracture of specimens first triggered initial reaction between Al and PTFE to release an amount of heat. Then ZrH2 was activated and decomposed, and participated in subsequent reaction to generate ZrC. The impact sensitivity of the specimens decreased with the increase of Al particle size.     

Studies on the flame propagation characteristic and thermal hazard of the premixed N2O/fuel mixtures

An experimental study was carried out to investigate the flame propagation and thermal hazard of the premixed N₂O/fuel mixtures, including NH₃, C₃H₈ and C₂H₄. The study provided the high speed video images and data about the flame locations, propagation patterns, overpressures and the quenching diameters during the course of combustion in different channels to elucidate the dynamics of various combustion processes. The onset decomposition temperature was determined using high-performance adiabatic calorimetry. It was shown that the order of the flame acceleration rate and thermal hazard was N₂O/C₂H₄>N₂O/C₃H₈>N₂O/NH₃.     

火药复合焊条焊接接头的微观组织及性能

为提高战场装备的应急抢修能力,以火药和2Al/3CuO系高热剂为焊接热源,开发了一种新型的便携式焊接材料——火药复合焊条,对其焊缝的组织形貌及性能进行研究.试验结果表明,火药复合焊条的焊接属于熔化焊,焊缝与基体之间存在明显的过渡区,焊缝成形良好,焊缝的抗拉强度大于400MPa,高于母材本身强度,能够满足战场应急抢修能力的需要.     

SiO_2在SHS铝热-重力分离法制备陶瓷内衬复合钢管中的作用

采用自蔓延铝热-重力分离法,制备了陶瓷内衬复合钢管,并系统研究了SiO_2添加剂对SHS燃烧过程、陶瓷层相对密度与组织结构、复合钢管力学性能的影响。经研究发现,SiO_2在铝热燃烧过程中作为稀释剂存在,随着SiO_2添加量增多,燃烧温度与蔓延速率下降,并使分布于α-Al_2O_3枝晶晶界处的亚稳定相FeO·Al_2O_3增多;陶瓷相对密度与复合钢管抗压溃强度在SiO_2含量为2wt％时出现极大值(分别为92.5％与430MPa);陶瓷硬度、断裂韧性与复合钢管抗压剪强度随SiO_2含量增加而降低。     

狭长密闭空间油气爆炸燃烧数值研究

基于不同控制机理制约不同反应步骤的分步反应燃烧机理,建立了RNG k-ε湍流模型和层流有限速率/涡耗散燃烧模型直接耦合的燃烧模型,采用TVD有限体积法,对充满等体积油气预混气的狭长密闭空间油气爆炸燃烧发生与发展过程进行了数值模拟.为了验证模型的正确性,根据计算结果分析了爆炸流场出现的火焰、压力波和化学反应等特征.所得计...