Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

Chain damage effects of multi-spaced plates by reactive jet impact

Chain damage is a new phenomenon that occurs when a reactive jet impacts and penetrates multi-spaced plates.The reactive jet produces mechanical perforations on the spaced plates by its kinetic energy(KE),and then results in unusual chain rupturing effects and excessive structural damage on the spaced plates by its deflagration reaction.In the present study,the chain damage behavior is initially demonstrated by experiments.The reactive liners,composed of 26 wt％Al and 74 wt％PTFE,are fabricated through a pressing and sintering process.Three reactive liner thicknesses of 0.08 CD,0.10 CD and 0.12 CD(charge diameter)are chosen to carry out the chain damage experiments.The results show a chain rupturing phenomenon caused by reactive jet.The constant reaction delay time and the different penetration velocities of reactive jets from liners with different thicknesses result in the variation of the deflagration position,which consequently determines the number of ruptured plates behind the armor.Then,the finite-element code AUTODYN-3D has been used to simulate the kinetic energy only-induced rupturing effects on plates,based on the mechanism of behind armor debris(BAD).The significant discrepancies between simulations and experiments indicate that one enhanced damage mechanism,the behind armor blast(BAB),has acted on the ruptured plates.Finally,a theoretical model is used to consider the BAB-induced enhancement,and the analysis shows that the rupturing area on aluminum plates depends strongly upon the KE only-induced pre-perforations,the mass of reactive materials,and the thickness of plates.     

Shock-induced reaction behaviors of functionally graded reactive material

In this paper, the ballistic impact experiments, including impact test chamber and impact double-spaced plates, were conducted to study the reaction behaviors of a novel functionally graded reactive material (FGRM), which was composed of polytetrafluoroethylene/aluminum (PTFE/Al) and PTFE/Al/bismuth trioxide (Bi₂O₃). The experiments showed that the impact direction of the FGRM had a significant effect on the reaction. With the same impact velocity, when the first impact material was PTFE/Al/Bi₂O₃, compared with first impact material PTFE/Al, the FGRM induced higher overpressure in the test chamber and larger damaged area of double-spaced plates. The theoretical model, which considered the shock wave generation and propagation, the effect of the shock wave on reaction efficiency, and penetration behaviors, was developed to analyze the reaction behaviors of the FGRM. The model predicted first impact material of the FGRM with a higher shock impedance was conducive to the reaction of reactive materials. The conclusion of this study provides significant information about the design and application of reactive materials.     

Experimental and numerical investigation of zirconium jet performance with different liner shapes design

This paper studies the shaped charge jet performance in terms of different liner shapes including conical,bell,hemispherical and bi-conical liners.The critical angles and the relevant flow velocities for the zir-conium liner material were calculated analytically and numerically using Autodyn hydro-code.The relationship between the critical collapse angle and the flow velocity was determined for the conditions of jet formation and coherency.Penetration tests according to the standard testing procedures of API-RP34 (Section-Ⅱ) were performed to validate the numerical predictions of the jet performance of the studied liners.It was found that the four shaped charge liners all produced coherent jets with different performances.The penetration depth of the shaped charges with the bell and the bi-conical liner shapes increased by 10.3％ and 22％,respectively,while the crater diameter of shaped charge with hemispherical liner increased by 85％ representing the formation of an explosively-formed-projectile (EFP),when they are compared with the corresponding jet characteristics of a conical liner shaped charge.     

Shaped charge penetration into high- and ultrahigh-strength Steel–Fiber reactive powder concrete targets

Experiments on shaped charge penetration into high and ultrahigh strength steel-fiber reactive powder concrete (RPC) targets were performed in this paper. Results show that the variation of penetration depth and crater diameter with concrete strength is different from that of shaped charge penetration into normal strength concrete (NSC). The crater diameter of RPC is smaller than that of NSC penetrated by the shaped charge. The jet particles are strongly disturbed and hardly reach the crater bottom because they pass through the narrow channel formed by jet penetration into the RPC. The effects of radial drift velocity and gap effects of jet particles for a shaped charge penetration into RPC target are discussed. Moreover, a theoretical model is presented to describe the penetration of shaped charge into RPC target. As the concrete strength increases, the penetration resistance increases and the entrance crater diameter decreases. Given the drift velocity and narrow crater channel, the low-velocity jet particles can hardly reach the crater bottom to increase the penetration depth. Moreover, the narrow channel has a stronger interference to the jet particles with increasing concrete strength; hence, the gap effects must be considered. The drift velocity and gap effects, which are the same as penetration resistance, also have significant effects during the process of shaped charge penetration into ultrahigh-strength concrete. The crater profiles are calculated through a theoretical model, and the results are in good agreement with the experiments.     

Influence of shaped charge structure parameters on the formation of linear explosively formed projectiles

The research of LEFP (linear explosive forming projectile) is of great value to the development of new warhead due to its excellent performance. To further improve the damage ability of the shaped charge warhead, a special shell overhanging structure was designed to increase the charge based on the traditional spherical charge, in which case the crushing energy of LEFP could be guaranteed. LS-DYNA was used to simulate different charge structures obtained by changing the number of detonation points, the length of shell platform, the radius of curvature and the thickness of liner. The RSM (response surface model) between the molding parameters of LEFP and the structural parameters of charge was established. Based on RSM model, the structure of shaped charge was optimized by using multi-objective genetic algorithm. Meanwhile, the formation process of jet was analyzed by pulsed X-ray photography. The results show that the velocity, length-diameter ratio and specific kinetic energy of the LEFP were closely related to the structural parameters of the shaped charge. After the optimization of charge structure, the forming effect and penetration ability of LEPP had been significantly improved. The experimental data of jet velocity and length were consistent with the numerical results, which verifies the reliability of the numerical results.     

The effect of sintering and cooling process on geometry distortion and mechanical properties transition of PTFE/Al reactive materials

In this research, the effect of the sintering and cooling process on geometry distortion and mechanical properties of PTFE/Al reactive material is investigated. Six particularly selected sintering temperatures, three different cooling modes (annealing cooling, normalizing cooling and rapid cooling), three different initial cooling temperatures, as well as six different final cooling temperatures were designed to compare the effects of sintering temperature, cooling rate, initial cooling temperature and final cooling temperature on the properties of reactive materials. Geometry distortion was quantitatively analyzed by a statistic on the dimensional changes of the specimens and microscopic morphology. A mechanical response properties transition from brittle to ductile was found and analyzed. By combining the thermodynamic properties of PTFE and unsteady heat conduction theory, mechanisms of cooling induced morphology change, temperature induced distortion and strength decrease were obtained. The results showed that the cooling rate has the most significant effect on the morphology transformation, while initial cooling temperature has more significant effect on the dimensional distortion than final cooling temperature. As to the mechanical properties transition from brittle to plastic, a more prominent effect of initial cooling temperature than cooling rate and final temperature was revealed.     

Investigation on the influence of the initial RDX crystal size on the performance of shaped charge warheads

Copper lined wave shaped shaped charges of particular design and liner metallurgy were used to investigate the effect of explosive crystal size on the resultant shaped charge jet parameters. Composition A3 with RDX of three different average crystal sizes, i.e. 30 μm, 100 μm and 300 μm were used in the investigation. All other parameters in the charge were kept constant and in particular, care was given to obtain consistent dimensional quality and liner microstructure, in order to prohibit the variation of other parameters. Specific flash-X-ray diagnostics were used in field tests to obtain the jet parameters from multiple firings of similar charges. It is found that the varying crystal size of the RDX has a marginal influence in the total jet length of the jets. However, it is also found that there is less variation between firings in the jet parameters for jets from the charges loaded with the crystal size of 100 μm.     

聚能射流侵彻下舰船钢与均质钢的等效关系

基于剩余穿深理论,依据聚能射流对钢靶板侵彻毁伤作用机理,推导出2种等效模型,并结合数值模拟建立了聚能射流侵彻下某舰船装甲钢与603钢靶板的等效关系。结果表明:当舰船钢厚度较小时,舰船钢与603装甲钢的等效厚度比约为1;当舰船钢厚度较大时,两者等效厚度比约为1.13。由此等效关系可给出用于战斗部考核性穿靶试验中相应均质靶板的确定厚度,从而为用603装甲钢靶代替该舰船钢进行聚能射流威力考核试验提供依据,达到了简化、经济、方便、有效的目的。     

Investigation of the shock compression behaviors of Al/PTFE composites with experimental and a 3D mesoscale-model

The responses of AI/PTFE reactive materials (RMs) under shock compression were investigated by a single-stage gas gun.A 3D mesoscale-model was established based on micro-computed tomography(micro-CT) slice images and confirmed with experimental results.In the high-pressure stage,the com-posites reacted partially,whereas there were no deviations between the partially reacted Hugoniot and the inert simulation results.The simulation reveals that the Teflon matrix melting on the high shock pressure.Melts and decomposition of the PTFE accelerated the diffusion of the atoms.Thus,the reactions of the Al/PrFE composites are more like a combustion rather than a detonation.     

聚能射流形成过程的理论建模与分析

分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。     

PTFE/Al反应材料制备工艺及性能

氟聚物基反应材料是一种主要由氟聚物和金属填料组成的亚稳态含能复合材料,也是近年来国外研究报道较多的一种新型含能材料.采用冷压、热烧结法制备了PTFE/Al反应材料,测试了其理化性能、热分解性能和力学性能,在此基础上,进一步研究了压制成型和烧结工艺参数.     

Effects of Mg/PTFE pyrotechnic compositions on reignition characteristics of base bleed propellants and heating mechanism

The effects of magnesium/polytetrafluoroethylene (Mg/PTFE) pyrotechnic compositions on the coupled flow field and reignition mechanism are important aspects governing the performance and range of base bleed projectiles (BBPs).Owing to a decrease in pressure and temperature when the BBP leaves the muzzle,rapid depressurization occurs,which extinguishes the base bleed propellant.The Mg/PTFE py-rotechnic composition pressed in the igniter of the base bleed unit (BBU) provides additional energy to the BBU via a chemical reaction.Thus,the extinguished base bleed propellant is reignited under the effect of high-temperature combustion gas jets from the igniter.In this study,a numerical analysis is conducted to evaluate the effects of PTFE and Mg granularity as well as Mg/PTFE pyrotechnic compo-sitions.Owing to the rapid depressurization,the temperature and pressure was found to decrease for different Mg/PTFE pyrotechnic compositions.However,the depressurization time increased as the PTFE granularity increased,the Mg granularity decreased,and the Mg content increased.When the pressure in the combustion chamber of the BBU decreased to the atmospheric pressure,the combustion gas jets from the igniter expand upstream (rather than downstream).However,these combustion gas jets exhibit different axial and radial expansion characteristics depending on the pyrotechnic compositions used.The results show that the reignition delay time,td,of the base bleed propellant was 377.608,94.27,387.243,523.966,and 221.094 ms for cases A-E,respectively.Therefore,it was concluded that the Mg/PTFE pyrotechnic composition of case B was the most beneficial for the reignition of the base bleed propellant,with the earliest addition of energy and mass to the BBP.     

Experimental investigation on enhanced damage to fuel tanks by reactive projectiles impact

Enhanced damage to the full-filled fuel tank,impacted by the cold pressed and sintered PTFE/AL/W reactive material projectile(RMP)with a density of 7.8 g/cm3,is investigated experimentally and theoretically.The fuel tank is a rectangular structure,welded by six pieces of 2024 aluminum plate with a thickness of 6 mm,and filled with RP-3 aviation kerosene.Experimental results show that the kerosene is ignited by the RMP impact at a velocity above 1062 m/s,and a novel interior ignition phenomenon which is closely related to the rupture effect of the fuel tank is observed.However,the traditional steel projectile with the same mass and dimension requires a velocity up to 1649 m/s to ignite the kerosene.Based on the experimental results,the radial pressure field is considered to be the main reason for the shear failure of weld.For mechanism considerations,the chemical energy released by the RMP enhances the hydrodynamic ram(HRAM)effect and provides additional ignition sources inside the fuel tank,thereby enhancing both rupture and ignition effects.Moreover,to further understand the enhanced ignition effect of RMP,the reactive debris temperature inside the kerosene is analyzed theoretically.The initiated reactive debris with high temperature provides effective interior ignition sources to ignite the kerosene,resulting in the enhanced ignition of the kerosene.     

多孔材料药型罩聚能射流的形成条件

依据Herrmann状态方程和斜冲击波关系估算了多孔材料药型罩压垮之前的冲击温升,求解了经过冲击压缩卸载后材料的声速。给出了多孔材料药型罩聚能射流的形成条件。初始冲击温升会使材料的声速和强度降低,从而使多孔材料聚能射流形成射流的高速和低速条件降低。     

Influence of a liquid-filled compartment structure on the incoming shaped charge jet stability

Liquid-filled compartment structure consists of a bulk steel plate with matrix blind holes which are filled with liquid and a steel front plate to seal up the liquid with rings and bolts.The liquid-filled compart-ment structure can resist the shaped charge warhead effectively.This paper presents experimental and theoretical investigations of the penetration ability of the residual shaped charge jet emerging from the liquid-filled compartment structure after the penetration process at different impact angles.On the basis of shock wave propagation theory,the influence of the liquid-filled compartment structure on jet sta-bility is analysed.The interferences of the liquid backflow caused by a reflected shock wave and a back plate on jet stability under different impact angles are also examined.In addition,the range of the disturbed velocity segments of the jet at different impact angles and the penetration ability of the re-sidual jet are obtained.A theoretical model is validated against the experimental penetration depths.     

Theoretical and numerical simulation study on jet formation and penetration of different liner structures driven by electromagnetic pressure

The use of a shaped liner driven by electromagnetic force is a new means of forming jets. To study the mechanism of jet formation driven by electromagnetic force, we considered the current skin effect and the characteristics of electromagnetic loading and established a coupling model of"Electric—Magnetic—Force"and the theoretical model of jet formation under electromagnetic force. The jet formation and penetration of conical and trumpet liners have been calculated. Then, a numerical simulation of liner collapse under electromagnetic force, jet generation, and the stretching motion were performed using an ANSYS multiphysics processor. The calculated jet velocity, jet shape, and depth of penetration were consistent with the experimental results, with a relative error of less than 10％. In addition, we calculated the jet formation of different curvature trumpet liners driven by the same loading condition and ob-tained the influence rule of the curvature of the liner on jet formation. Results show that the theoretical model and the ANSYS multiphysics numerical method can effectively calculate the jet formation of liners driven by electromagnetic force, and in a certain range, the greater the curvature of the liner is, the greater the jet velocity is.     

A study on the surface overpressure distribution and formation of a double curvature liner under a two-point initiation

The formation mechanism of an EFP(explosively formed projectile) using a double curvature liner under the overpressure effect generated by a regular oblique reflection was investigated in this paper.Based on the detonation wave propagation theory,the change of the incident angle of the detonation wave collision at different positions and the distribution area of the overpressure on the surface of the liner were calculated.Three-dimensional numerical simulations of the formation process of the EFP with tail as well as the ability to penetrate 45# steel were performed using LS-DYNA software,and the EFP ve-locity,the penetration ability,and the forming were assessed via experiments and x-ray photographs.The experimental results coincides with those of the simulations.Results indicate that the collision of the detonation wave was controlled to be a regular oblique reflection acting on the liner by setting the di-mensions of the unit charge and maintaining the pressure at the collision point region at more than 2.4 times the CJ detonation when the incident angle approached the critical angle.The distance from the liner midline to the boundary of the area within which the pressure ratio of the regular oblique reflection pressure to the CJ detonation pressure was greater than 2.5,2,and 1.5was approximately 0.66 mm,1.32 mm,and 3.3 mm,respectively.It is noted that pressure gradient caused the liner to turn inside out in the middle to form the head of the EFP and close the two tails of the EFP at approximately 120μs.The penetration depth of the EFP into a 45# steel target exceeded 30 mm,and there was radial expansion between the head and tail of the EFE increasing the penetration resistance of the EFP.Therefore,the structural size of the unit charge and the liner can be further optimized to reduce resistance to increase the penetration ability of the EFP.     

A numerical study on the disturbance of explosive reactive armors to jet penetration

The disturbance of flat and V-shaped sandwich reactive armor configurations to shaped-charge jet is studied by a numerical approach. The disturbing and cutting effects of the two reactive armor configurations to the jet are successfully captured. The predicted disturbance characteristics and patterns are in fairly good agreement with the X-ray photographic observations. The residual depth of penetration into a semi-infinitive homogeneous steel target behind the reactive armor is computed for a series of jet/armor parameters. For the flat configuration, it is demonstrated that the residual penetration depth is not significantly reduced for a normal impact while it is reduced up to 75% for an oblique impact. In comparison, the V-shaped configuration reduces the penetration depth of the jet to 90%, and it is observed that the penetration depth is not sensitive to the V-shaped angle.