A stochastic model for burn‐in procedures in accelerated environment

Burn‐in procedure is a manufacturing technique that is intended to eliminate early failures of system or product. Burning‐in a component or system means to subject it to a period of use prior to being used in field. Generally, burn‐in is considered expensive and so the length of burn‐in is typically limited. Thus, burn‐in is most often accomplished in an accelerated environment in order to shorten the burn‐in process. A new failure rate model for an accelerated burn‐in procedure, which incorporates the accelerated ageing process induced by the accelerated environmental stress, is proposed. Under a more general assumption on the shape of failure rate function of products, which includes the traditional bathtub‐shaped failure rate function as a special case, upper bounds for optimal burn‐in time will be derived. A numerical example will also be given for illustration. © 2006 Wiley Periodicals, Inc. Naval Research Logistics, 2006     

爆炸复合接头剪切强度测试方法研究

参照正交各向异性层压复合板层间剪切强度的测试方法,提出了用于测试爆炸复合接头复合界面剪切强度的3种方法;并建立三维有限元模型,分别对3种测试方法进行模拟;最后分别对3种方法进行了测试试验.结果表明,3种试验方法均能有效测试爆炸复合接头的剪切强度,其中对称试件双切口拉伸法最适合实际应用.     

基于EMD的改进小波阈值降噪法在超声信号处理中的应用

针对超声检测回波信号中的大量噪声,分析了超声检测回波信号的特性,考虑经验模式分解（EMD）和小波哗噪的优点,在改进阈值函数基础上提出一种基于EMD的小波阈值降噪方法．该方法利用EMD对超声信号进行分解,对高频分量用改进小波阈值函数方法进行处理,再结合低频分量重构得到降噪信号．仿真实验结果表明,该方法降噪效果优于小波软、硬阂值降噪,进一步提高了重建信号的信噪比,降低了其均方根误差,是一种可行的超声信号降噪方法．     

Comparison between constant‐stress and step‐stress accelerated life tests under Time Constraint

By running life tests at higher stress levels than normal operating conditions, accelerated life testing (ALT) quickly yields information on the lifetime distribution of a test unit. The lifetime at the design stress is then estimated through extrapolation using a regression model. In constant‐stress testing, a unit is tested at a fixed stress level until failure or the termination time point of test, whereas step‐stress testing allows the experimenter to gradually increase the stress levels at some prefixed time points during the test. In this work, the optimal k‐level constant‐stress and step‐stress ALTs are compared for the exponential failure data under complete sampling and Type‐I censoring. The objective is to quantify the advantage of using the step‐stress testing relative to the constant‐stress one. Assuming a log‐linear life–stress relationship with the cumulative exposure model for the effect of changing stress in step‐stress testing, the optimal design points are determined under C/D/A‐optimality criteria. The efficiency of step‐stress testing to constant‐stress one is then discussed in terms of the ratio of optimal objective functions based on the information matrix. © 2013 Wiley Periodicals, Inc. Naval Research Logistics 00: 000–000, 2013     

目标识别中的传感器管理方法

基于假设检验的方法,研究了目标识别中的传感器管理方法。分别以用于假设检验问题中的最大后验概率、最小代价函数和最大正确检测概率为目标函数,给出了用于目标识别问题的多传感器管理方法,并针对目标识别问题的特点,对其进行了相应的改进。通过对一定场景的仿真,比较了三种不同方法的识别正确率和平均采样次数,分析了各种方法的特点。     

航空电子总线测试系统的设计与实现

现代航空电子综合化系统通常建立在M IL-STD-1533B多路传输数据总线通信网络基础之上,总线控制器(BC)和各个远程终端(RT)必须满足M IL-STD-1553B规定的各项协议指标要求,才能正确地联网通讯。讨论了某型航空电子总线测试系统的设计与实现,主要探讨了此系统的软、硬件开发,系统组成及其BC和RT有效性测试的主要内容和要求。在实际应用中收到了很好的效果。     

步进加速退化试验及其在电子产品可靠性评估中的应用

为快速评估具有高可靠、长寿命特点的电子产品的可靠性，提出了使用步进加速退化试验技术的方法。文中首先给出了步进加速退化的试验方法及基本假设，然后给出了步进退化数据向恒加退化数据的折算方法，在此基础上提出了基于伪失效寿命的步进加速退化可靠性评估算法，最后利用试验数据对该方法进行了验证。该方法与恒加退化试验相比，在保持样本量不变的基础上，可以极大地缩短试验时间，因此，具有更高的效费比。     

防火涂料性能要求及测试方法探讨

介绍了饰面型防火涂料、电缆防火涂料、钢结构防火涂料以及混凝土防火涂料的理化性能要求及防火性能要求。重点阐述了这些防火涂料防火性能的测试方法。     

Weibull型产品的可靠性验证

讨论了Weibull型产品的可靠性验证问题 ,首先分析了Weibull型产品分布参数的无信息验前分布问题 ,利用验前信息可以得到分布参数的验前概率密度函数 ,进而分析了产品的可靠性验证问题 ,顾及了使用方利益和生产方利益。仿真算例表明 ,使用方利益和生产方利益是相互折衷的。     

一种胆碱酯酶贮存寿命的预测方法

用差热分析 (DTA)和等温加速老化法 ,测定了用生物化学方法检测有机磷、氨基甲酸酯类农药或毒剂的试剂———胆碱酯酶的贮存寿命。获得了所测定的该种胆碱酯酶的贮存寿命与贮存温度之间的关系式。这种测定方法简便快捷、实用可靠。