粉末粒度对储氢电极电化学性能的影响

以M1（NiCoMnTi）5为例,系统研究了粉末粒度对储氢电极电化学性能的影响。结果表明,在试验粒度范围内,合金粉越细,其放电容量越高,高倍率放电性能和循环稳定性也越好;将两种不同粒度的合金粉混合使用时,粒径相差越大,其放电容量越高。且当粗细粉质量比为7：3时,放电容量最高。     

一种RetinaNet与SE融合的航空取证目标检测算法

针对在开展航空侦察取证时缺乏自动化、智能化取证手段的情况,提出了一种基于Reti-naNet与SE融合的航空取证目标检测算法,解决目标尺度变化大、数据集中类别不均衡的问题,并通过SE (squeeze-excitations)模块引入注意力机制进一步改进性能.该改进算法中的特征金字塔网络FPN可有效应对目标尺寸变化较大...     

高速电弧喷涂耐磨涂层性能研究

将低碳马氏体和3Cr13+AlRE伪合金高速电弧喷涂层进行了性能和组织结构的对比分析。实验结果表明,与伪合金涂层相比,低碳马氏体涂层呈现出更优异的力学性能、耐磨性能和机械加工性能。该涂层可用于发动机曲轴等零件的再制造。     

水下制氢反应室动态过程数值分析

为研究水下制氢反应室的动态过程规律,基于化学反应动力学和单液滴运动学得到合金/水反应转化率,并在最小自由能法计算得到生成物各组分摩尔数的基础上利用质量守恒方程得到室内各物质质量变化规律。在建立非线性移动边界螺旋管动态模型的前提下,利用能量守恒方程得到室内热力参数变化规律,进而完成制氢反应室动态过程详尽模型的建立。利用该模型编写计算程序,完成某水下制氢反应室动态过程仿真。结果表明,各仿真曲线较好地反映了对应参数的动态变化规律,验证了模型建立与仿真的正确性;合金/水反应转化率决定了反应室的物质质量变化规律及其能量释放特性。该模型可以作为制氢反应室动态特性分析及其过程控制研究的基础模型。     

基于属性的舰载机航材备件品种确定方法

航材备件品种确定是舰载机供应保障工作的重要内容。基于属性对舰载机航材备件品种确定进行研究。基于粗糙集理论对属性集进行属性约简,确定航材备件品种确定的主要影响属性,然后基于属性约简进行航材备件品种确定。给出了单属性、顺次属性和多属性的品种决策方法。最后结合实例进行了应用分析。     

基于RUP的航空兵作战C~4ISR体系结构研究

本文分析了C4ISR系统的建模特点,对当前主流体系结构模型开发方法进行了比较,提出了运用Rational统一过程（RUP）开发DoDAF体系结构视图产品,并分析了其可行性。结合航空兵作战的特点,采用Rational ROSE建模工具开发了的相关视图产品,描述了航空兵作战过程,证明了RUP对体系结构的开发有着良好的支持作用。     

基于解析算法的声纳浮标搜潜系统定位精度分析

针对基于位置时间参数解析算法的声纳浮标阵搜潜系统的定位精度问题,采用定性和定量分析相结合的方法展开了研究。从解析定位模型出发,首先定性分析浮标自身的定位误差与传感器测时误差对航速及航向角计算的影响;然后选取评价指标,采用蒙特卡洛方法进行了仿真分析,得到了不同仿真条件下各个因素对定位精度具体的影响关系,这些结论为根据精度参数合理选择浮标阵的数量及布放阵型提供了依据。     

镁合金表面电弧喷涂Fe基非晶纳米晶涂层的性能

采用自动化高速电弧喷涂技术在镁合金基体上制备了FeCrBSiMoNbW非晶纳米晶涂层。采用Flir A20M型红外热像仪对Fe基非晶纳米晶喷涂层的表面温度场进行了实时监测。对Fe基非晶纳米晶涂层和传统的3Cr13涂层的组织结构、力学性能以及摩擦学性能进行了对比分析。实验结果表明：Fe基非晶纳米晶涂层组织致密,孔隙率低,具有相对较高的硬度和拉伸结合强度;形成了非晶相和纳米晶相组成的复合结构,使得涂层具备较好的耐磨减摩性能。     

Study of high-speed-impact-induced conoidal fracture of Ti alloy layer in composite armor plate composed of Ti-and Al-alloy layers

In order to understand the mechanism of conoidal fracture damage caused by a high-speed fragment-simulating projectile in titanium alloy layer of a composite armor plate composed of titanium- and aluminum-alloy layers, the ballistic interaction process was successfully simulated based on the Tuler-Butcher and GISSMO coupling failure model. The simulated conoidal fracture morphology was in good agreement with the three-dimensional industrial-computed-tomography image. Further, three main damage zones (zones I, II, and III) were identified besides the crater area, which are located respectively near the crater area, at the back of the target plate, and directly below the crater area. Under the high-speed-impact conditions, in zone II, cracks began to form at the end of the period of crack formation in zone I, but crack formation in zone III started before the end of crack formation in zone II. Further, the damage mechanism differed for different stress states. The microcracks in zone I were formed both by void connection and shear deformation. In the formation of zone I, the stress triaxiality ranged from-2.0 to-1.0, and the shear failure mechanism played a dominant role. The microcracks in zone II showed the combined features of shear deformation and void connection, and during the for-mation process, the stress triaxiality was between 0 and 0.5 with a mixed failure mode. Further, the microcracks in zone III showed obvious characteristics of void connection caused by local melting. During the zone III formation, the triaxiality was 1.0-1.9, and the ductile fracture mechanism was dominant, which also reflects the phenomenon of spallation.     

Numerical simulation study on penetration performance of depleted Uranium (DU) alloy fragments

Due to its high strength, high density, high hardness and good penetration capabilities, Depleted ura-nium alloys have already shined in armor-piercing projectiles. There should also be a lot of room for improvement in the application of fragment killing elements. Therefore, regarding the performance of the depleted uranium alloy to penetrate the target plate, further investigation is needed to analyze its advantages and disadvantages compared to tungsten alloy. To study the difference in penetration per-formance between depleted uranium alloy and tungsten alloy fragments,firstly, a theoretical analysis of the adiabatic shear sensitivity of DU and tungsten alloys was given from the perspective of material constitutive model. Then, taking the cylindrical fragment penetration target as the research object, the penetration process and velocity characteristics of the steel target plates penetrated by DU alloy frag-ment and tungsten alloy fragment were compared and analyzed, by using finite element software ANSYS/LS-DYNA and Lagrange algorithm. Lastly, the influence of different postures when impacting target and different fragment shapes on the penetration results is carried out in the research. The results show that in the penetration process of the DU and tungsten alloy fragments, the self-sharpening properties of the DU alloy can make the fragment head sharper and the penetrating ability enhance. Under the same conditions, the penetration capability of cylindrical fragment impacting target in vertical posture is better than that in horizontal posture, and the penetration capability of the spherical fragment is slightly better than that of cylindrical fragment.