基于高压脉冲等离子体技术的TNT废水处理研究

针对报废弹药处理过程中产生的TNT废水毒性大、处理难的特点,分析TNT废水的特性和当前处理方法现状,提出基于高压脉冲等离子体技术的TNT废水处理方法;分析脉冲等离子体对废水的处理降解机理,给出双向窄脉冲电源和气液固三相反应器的设计方案．研究表明,利用脉冲放电等离子体技术可提高TNT废水的处理效率,有效解决报废弹药TNT废水处理难题．     

基于组合赋权雷达图实现电网电能质量综合评估

将改进的组合赋权雷达图方法用于电网电能质量综合评估。对主观、客观赋权法组合,基于组合权重与原权重之间的偏差尽可能小的优化思想,求取雷达图中各项指标的组合权值。利用各指标对应的扇形区域的对角线作为指标轴绘制雷达图,不仅最大限度体现各指标的独立权重,也反映了各指标之间的相互影响。利用雷达图的面积和周长两个变量完成对电能质量的综合评估。最后通过应用实例,验证了论文方法的合理性和在电能质量综合评估中的有效性。     

Analysis on damage characteristics and detonation performance of solid rocket engine charge subjected to jet

To further explore the damage characteristics and impact response of the shaped charge to the solid rocket engine (SRE) in storage or transportation, protective armor was designed and the shelled charges model (SCM)/SRE with protective armor impacting by shaped charge tests were conducted. Air overpressures at 5 locations and axial acceleration caused by the explosion were measured, and the experimental results were compared with two air overpressure curves of propellant detonation obtained by related scholars. Afterwards, the finite element software AUTODYN was used to simulate the SCM impacted process and SRE detonation results. The penetration process and the formation cause of damage were analyzed. The detonation performance of TNT, reference propellant, and the propellant used in this experiment was compared. The axial acceleration caused by the explosion was also analyzed. By comprehensive comparison, the energy released by the detonation of this propellant is larger, and the HMX or Al particles contained in this propellant are more than the reference propellant, with a TNT equivalent of 1.168–1.196. Finally, advanced protection armor suggestions were proposed based on the theory of woven fabric rubber composite armor (WFRCA).     

聚能射流形成过程的理论建模与分析

分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。     

精确制导前沿成像探测技术

回顾了精确制导技术的发展历程,分析了精确制导成像探测技术发展过程中面临的挑战与未来的主要发展方向。结合太赫兹、量子和超材料等前沿技术的发展动态,分别梳理了太赫兹雷达、量子雷达以及超材料雷达三种典型的精确制导前沿成像探测技术的技术背景、发展脉络、基本原理、技术优势。这三种成像探测技术有望为精确制导技术应对未来新型战争形态带来的挑战提供可行的技术途径。研究成果可为未来精确制导技术的深入可持续发展提供参考,并对提升精确制导武器的打击与拦截作战效力具有重大意义。     

采用射流掺混增强的前可调面积涵道引射器数值模拟

为了提高风扇外涵和核心机驱动风扇级外涵流体的掺混效率,提出一种采用射流掺混增强的前可调面积引射器设计方案。通过数值模拟的手段对流量特性、流动掺混和总压损失等方面进行了研究,并同基准模型进行了对比分析,结果表明：采用波瓣混合器结构的前可调面积引射器设计,显著地增加了较高出口背压工况下风扇外涵的流通能力;新的设计方案不仅没有增加低出口背压工况下的总压损失,还减小了高背压出口工况下的流动损失;流向涡的特征尺度是提高掺混效率的关键,可以进一步优化波瓣混合器几何轮廓,以满足调节机构对结构设计的要求。     

Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

空化射流实验研究

空化水射流技术是将空化作用引入到高压水射流而形成的一种新型高压水射流技术,在同等条件下,空化射流相对于普通高压水射流具有破碎和切割能力更高的特点。通过数值模拟和实验方法对空化技术进行研究,进行了喷嘴流场的数值模拟计算,设计了空化射流实验装置及空化喷嘴。以生锈铁板为研究对象,分别进行了喷嘴型号、打击时间、入口压力、靶距和扩散段长度的空化射流打击效果对比实验,研究了空化参数对空化效果的影响。实验结果表明角形喷嘴进行淹没射流的空化效果较好,空化射流除锈具有最优打击时间。不同的入口压力对应不同的最佳靶距。     

高超声速圆球绕流流场及其近尾尾迹流场电磁散射特性分析

采用分段线性电流密度递归卷积时域有限差分(PLJERC FDTD)方法计算高超声速导电金属球绕流流场及其近尾尾迹流场电磁散射特性,分析等离子体绕流流场RCS的频率特性、双站散射特性、极化特性及随飞行高度、飞行马赫数、入射角的变化关系.计算表明,前向散射方向是全方位散射中RCS取得最大值的方向;马赫数较大(本文Ma≥14)时,入射波频率增大、马赫数增大及飞行高度降低,绕流流场前向RCS增大.马赫数较小(本文Ma≤10)时,飞行马赫数、高度及入射角变化对绕流流场UHF、L、S波段后向RCS和双站RCS影响很小;在UHF、L波段,绕流流场及本体的后向RCS差距较小.马赫数较大时,大范围过密等离子体尾迹的形成使得电磁波垂直轴线入射时绕流流场增大了目标本体的后向RCS;在L、S波段,绕流流场后向RCS曲线可用一条直线逼近.     

合成孔径声纳中RD和ω-k成像算法的比较

从聚焦能力和处理相关的空变特性的能力两方面 ,对合成孔径声纳中几种成像算法进行比较 .给出了RD(RangeDoppler)和ω -k算法的对水池实验数据成像的结果 .