A study on the surface overpressure distribution and formation of a double curvature liner under a two-point initiation

The formation mechanism of an EFP(explosively formed projectile) using a double curvature liner under the overpressure effect generated by a regular oblique reflection was investigated in this paper.Based on the detonation wave propagation theory,the change of the incident angle of the detonation wave collision at different positions and the distribution area of the overpressure on the surface of the liner were calculated.Three-dimensional numerical simulations of the formation process of the EFP with tail as well as the ability to penetrate 45# steel were performed using LS-DYNA software,and the EFP ve-locity,the penetration ability,and the forming were assessed via experiments and x-ray photographs.The experimental results coincides with those of the simulations.Results indicate that the collision of the detonation wave was controlled to be a regular oblique reflection acting on the liner by setting the di-mensions of the unit charge and maintaining the pressure at the collision point region at more than 2.4 times the CJ detonation when the incident angle approached the critical angle.The distance from the liner midline to the boundary of the area within which the pressure ratio of the regular oblique reflection pressure to the CJ detonation pressure was greater than 2.5,2,and 1.5was approximately 0.66 mm,1.32 mm,and 3.3 mm,respectively.It is noted that pressure gradient caused the liner to turn inside out in the middle to form the head of the EFP and close the two tails of the EFP at approximately 120μs.The penetration depth of the EFP into a 45# steel target exceeded 30 mm,and there was radial expansion between the head and tail of the EFE increasing the penetration resistance of the EFP.Therefore,the structural size of the unit charge and the liner can be further optimized to reduce resistance to increase the penetration ability of the EFP.     

基于随机拟合的悬浮式深弹弹阵特征建模

通过分析悬浮式深弹发射后在空中的弹道特性,建立了深弹弹着点坐标的计算模型。采取蒙特卡洛方法,分别对舰艇六自由度状态下,单管和六联装火箭深弹的弹着点坐标进行了仿真计算,对弹着点的分布规律进行了研究,并得出弹着点的联合密度函数。结果表明,在发射参数存在正态扰动下,弹着点散布区域均呈椭圆形分布,弹着点坐标均仍服从正态分布。     

Numerical simulation of base flow with hot base bleed for two jet models

In order to improve the benefits of base bleed in base flow field, the base flow with hot base bleed for two jet models is studied. Two-dimensional axisymmetric Navier–Stokes equations are computed by using a finite volume scheme. The base flow of a cylinder afterbody with base bleed is simulated. The simulation results are validated with the experimental data, and the experimental results are well reproduced. On this basis, the base flow fields with base bleed for a circular jet model and an annulus jet model are investigated by selecting the injection temperature from 830 K to 2200 K. The results show that the base pressure of the annular jet model is higher than that of the circular jet model with the changes of the injection parameter and the injection temperature. For the circular jet model, the hot gases are concentrated in the vicinity of the base. For the annular jet model, the bleed gases flow into the shear layer directly so that the hot gases are concentrated in the shear layer. The latter temperature distribution is better for the increase of base pressure.     

A numerical study on the disturbance of explosive reactive armors to jet penetration

The disturbance of flat and V-shaped sandwich reactive armor configurations to shaped-charge jet is studied by a numerical approach. The disturbing and cutting effects of the two reactive armor configurations to the jet are successfully captured. The predicted disturbance characteristics and patterns are in fairly good agreement with the X-ray photographic observations. The residual depth of penetration into a semi-infinitive homogeneous steel target behind the reactive armor is computed for a series of jet/armor parameters. For the flat configuration, it is demonstrated that the residual penetration depth is not significantly reduced for a normal impact while it is reduced up to 75% for an oblique impact. In comparison, the V-shaped configuration reduces the penetration depth of the jet to 90%, and it is observed that the penetration depth is not sensitive to the V-shaped angle.     

东突恐怖主义成因分析

突厥文化和泛突厥主义的泛滥、伊斯兰复兴运动和泛伊斯兰主义的传播、新疆周边国家各种恐怖势力的影响、国际敌对势力的怂恿、改革开放以来国际交流的加强以及新疆特殊的地理位置 ,是我国新疆地区“东突”恐怖主义形成的重要条件 ,并对“东突”恐怖主义的泛滥起到了催化作用     

子母深弹反鱼雷攻击效能及仿真

火箭深弹是水面舰艇拦截鱼雷的常用武器,为提高火箭深弹拦截鱼雷的概率,提出了子母深弹的概念,将地面火炮中常用的子母弹技术应用于深弹反鱼雷攻击中,通过分析子母弹的散布特性,来比较子母深弹和火箭深弹毁伤鱼雷的效能,并通过Monte-Carlo法仿真了这一过程,分析了影响子母深弹的毁伤概率的因素。     

倾斜顶棚影响顶棚射流的计算机模拟研究

对倾斜顶棚的传统模拟方法进行了改进,提出了分解重力场的模拟方法;利用场模拟软件FDS,采用改进后的方法模拟研究了倾斜无梁顶棚对顶棚射流的温度、速度以及定温探测器响应区域的影响规律;根据研究结果,为实际应用提出了可行性建议。     

25nm鱼鳍型场效应晶体管中单粒子瞬态的工艺参数相关性

基于TCAD(Technology Computer-Aided Design)3-D模拟,研究了25 nm鱼鳍型场效应晶体管(Fin Field Effect Transistor,FinFET)中单粒子瞬态效应的工艺参数相关性。研究表明一些重要工艺参数的起伏会对电荷收集产生显著影响,从而影响到电路中传播的SET(Single Event Transient)脉冲宽度。对于最佳工艺拐角,离子轰击后收集的电荷量可以降低约38%,而在最坏工艺拐角下,收集的电荷量则会增加79%。这些结论对FinFET工艺下的SET减缓及抗辐射加固设计提供了一种新的思路。     

多孔材料药型罩聚能射流的形成条件

依据Herrmann状态方程和斜冲击波关系估算了多孔材料药型罩压垮之前的冲击温升,求解了经过冲击压缩卸载后材料的声速。给出了多孔材料药型罩聚能射流的形成条件。初始冲击温升会使材料的声速和强度降低,从而使多孔材料聚能射流形成射流的高速和低速条件降低。     

炸药装药在压剪加载下的起爆特点

进行了两类压剪加载实验：（１）利用石英的平面正碰撞产生压剪加载的实验,采用电磁质速法测试装药试件内部不同质点的运动情况,分析炸药装药中发生化学反应的可能性;（２）在压剪炮上采用平行倾斜碰撞产生压剪加载的实验,观测炸药装药爆炸的可能性。由实验可以看出：在亚爆轰状态的压缩加载应力条件下,剪切的联合作用对炸药的起爆起到敏化作用,适当比例的压剪加载造成更加敏感的炸药起爆响应。文中给出了起爆响应规律和响应机制的实验分析。