随动定向战斗部破片飞散特性研究

针对防空导弹常规破片式杀伤战斗部使用中存在能量利用率低的缺陷,提出采用随动定向战斗部的观点。建立随动定向战斗部的破片动态飞散区和飞散速度的计算模型,采用数值解析方法,解决在复杂弹目交会条件下破片的飞散区域与打击速度的计算问题．并用MATLAB软件对建立的模型进行验证,得出仿真结果与实际结果一致,这表明模型是合理、正确的。     

镁合金表面电弧喷涂Fe基非晶纳米晶涂层的性能

采用自动化高速电弧喷涂技术在镁合金基体上制备了FeCrBSiMoNbW非晶纳米晶涂层。采用Flir A20M型红外热像仪对Fe基非晶纳米晶喷涂层的表面温度场进行了实时监测。对Fe基非晶纳米晶涂层和传统的3Cr13涂层的组织结构、力学性能以及摩擦学性能进行了对比分析。实验结果表明：Fe基非晶纳米晶涂层组织致密,孔隙率低,具有相对较高的硬度和拉伸结合强度;形成了非晶相和纳米晶相组成的复合结构,使得涂层具备较好的耐磨减摩性能。     

Investigations on influence of rifle automatics system action on values of energetic efficiency coefficient of muzzle brakes

The objective of the paper was to compare values of the muzzle brake efficiency coefficient for a rifle with active or inactive automatics systems. Special laboratory stand designed for investigating the recoil process was used. The motion of the rifle was detected by the use of the laser interferometer and the optical camera. The recoil velocity time courses were determined by smoothing and differentiation of experimental position records. The results of the experiments indicated that in the case of an active automatics system two values of the recoil velocity can be used for calculation of the energetic efficiency coefficient: the maximum recoil velocity and the final recoil velocity at the end of the automatics action cycle. The values of the coefficient, calculated using these two values of the recoil velocity, distinctly differ. However, it was shown that their values indicate the same relation between the efficiency of various muzzle brakes. The value of the efficiency coefficient, determined on the basis of the final recoil velocity value, is practically the same as that determined on the basis of the final recoil velocity value for the rifle with an inactive automatics system.     

钢管在冲击荷载作用下的变形与失效破坏

为研究钢管在弹体侵彻过程中的变形特点,基于ANSYS/LS-DYNA软件,采用Johnson-Cook模型,模拟了半球形弹体以不同速度正向冲击钢管时的非线性动力响应情况。结果表明：弹体速度越小,钢管的抗侵彻性能越好;弹体速度越接近临界破坏速度,钢管降低弹体速度的能力就越明显;弹体冲击钢管时,钢管上表面比下表面更容易产生大变形,消耗更多的弹体动能,并在抗侵彻过程中伴有局部凹陷、蝶形变形和贯穿现象。实验结果可为圆柱壳结构钢管在冲击荷载作用下的耗能分析提供参考。     

新型舰炮使用测速雷达后观测距离偏差射击校正方法

针对测速雷达精确校正初速后的观测距离偏差校正方法进行研究,建立不同校正方法校正量计算模型,对比分析不同校正方法校正精度,得出了使用测速雷达精确校正初速后观测距离偏差应采用折合空气密度校正精度高的结论,为中大口径舰炮部队作战与训练和装备的研制改进提供依据。     

Study of nano-nitramine explosives: preparation,sensitivity and application

Nano-nitramine explosives (RDX, HMX, CL-20) are produced on a bi-directional grinding mill. The scanning electron microscope (SEM) observations show that the prepared particles are semi-spherical, and the narrow size distributions are characterized using the laser particle size analyzer. Compared with the micron-sized samples, the nano-products show obvious decrease in friction and impact sensitivities. In the case of shock sensitivities, nano-products have lower values by 59.9% (RDX), 56.4% (HMX), and 58.1% (CL-20), respectively. When nano-RDX and nano-HMX are used in plastic bonded explosives (PBX) as alternative materials of micron-sized particles, their shock sensitivities are significantly decreased by 24.5% (RDX) and 22.9% (HMX), and their detonation velocities are increased by about 1.7%. Therefore, it is expected to promote the application of nano-nitramine explosives in PBXs and composite modified double-based propellants (CMDBs) so that some of their properties would be improved.     

Long-rod penetration: the transition zone between rigid and hydrodynamic penetration modes

Long-rod penetration in a wide range of velocity means that the initial impact velocity varies in a range from tens of meters per second to several kilometers per second. The long rods maintain rigid state when the impact velocity is low, the nose of rod deforms and even is blunted when the velocity gets higher, and the nose erodes and fails to lead to the consumption of long projectile when the velocity is very high due to instantaneous high pressure. That is, from low velocity to high velocity, the projectile undergoes rigid rods, deforming non-erosive rods, and erosive rods. Because of the complicated changes of the projectile, no well-established theoretical model and numerical simulation have been used to study the transition zone. Based on the analysis of penetration behavior in the transition zone, a phenomenological model to describe target resistance and a formula to calculate penetration depth in transition zone are proposed, and a method to obtain the boundary velocity of transition zone is determined. A combined theoretical analysis model for three response regions is built by analyzing the characteristics in these regions. The penetration depth predicted by this combined model is in good agreement with experimental result.     

Scale-up synthesis and characterization of 2,6-diamino-3,5-dinitropyrazine-1-oxide

2,6-diamino-3,5-dinitropyrazine-1-oxide (ANPZO), as an insensitive high explosive, with a high yield and excellent purity has been prepared at pilot plant scale by an improved method. The synthesized ANPZO is characterized by IR, laser granularity measurement, SEM and HPLC. The particle analysis revealed that the improved method could offer desired product with average particle size of 40 μm and high purity (>98.45%). The experimental parameters exhibited that the detonation velocity of the formulation based on ANPZO was higher than that of the corresponding TATB formulation. The DSC curve showed that the exothermic decomposition of the product occurred at the temperature between 300.5 °C and 360.4 °C. Furthermore, the sensitivity test suggests its safe nature towards mechanical stimulus.     

Theoretical study of an energetic material di-1H-1,3,4-triazole derivatives

Computations by density functional theory (DFT) method are performed on a series of di-1H-1,3,4-triazole derivatives with different substituents and linkages. The heat of formation (HOF) is predicted by the designed isodesmic reactions. The predicted results reveal that –N₃ and –NN– groups are effective structural units for increasing the HOF values of the di-1H-1,3,4-triazole derivatives. The HOMO–LUMO gap is affected by the substituents and linkage groups. Detonation performance is evaluated using the Kamlet–Jacobs approach based on the calculated density and HOF. The results indicate that –NO₂, –NF₂, –NH–, –NH–NH– and –NN– groups are helpful for enhancing the detonation properties of di-1H-1,3,4-triazole derivatives. The bond dissociation energy and bond order of the weakest bonds are analyzed to investigate their stability. It is observed that the –CH₂–, –CH₂–CH₂– and –CHCH– groups are effective structural units for improving the stabilities of these derivatives. Considering the detonation performance and the stability, five compounds are screened as the potential candidates for high energy density materials.     

Analysis on the resistive force in penetration of a rigid projectile

According to the dimensionless formulae of DOP (depth of penetration) of a rigid projectile into different targets, the resistive force which a target exerts on the projectile during the penetration of rigid projectile is theoretically analyzed. In particular, the threshold V_c of impact velocity applicable for the assumption of constant resistive force is formulated through impulse analysis. The various values of V_c corresponding to different pairs of projectile-target are calculated, and the consistency of the relative test data and numerical results is observed.