潜艇结构强度研究的新近进展

本文从结构材料、结构形式、非线性分析、组合壳体和端盖强度以及结构的减振降噪等方面论述了潜艇结构强度研究的新近进展,并指出了今后的研究方向。     

一种定征层状平面结构界面粘接强度的兰姆波方法

置于层状平面结构表面的斜劈超声换能器被用于激发和接收多模兰姆波。文章首先分析了采用多模兰姆波的幅频特性定征界面粘接强度的可行性。基于Ritec-SNAP 超声测量系统,建立了采用兰姆波方法定征层状结构界面粘接强度的实验系统。对于给定的层状平面结构,将粘接层的固化过程用于模拟粘接层界面强度的变化过程。对于不同的粘接层固化时间,实验测得的多模兰姆波幅频曲线明显不同。借助于声——超声技术中的应力波因子,给出了兰姆波应力波因子的定义。实验结果显示,兰姆波应力波因子与间接表示界面粘接强度的固化时间之间存在确定的单调对应关系,表明将多模兰姆波的应力波因子用于定征层状平面结构的界面粘接强度是可行的。     

倾斜微型桩桩身参数敏感性有限元分析

基于有限元强度折减法,结合工程实例,利用软件ANSYS对不同倾角微型桩加固边坡以及倾斜微型桩的设桩位置、锚固深度和桩排距等桩身参数对边坡稳定性的影响进行了数值模拟分析。结果表明:微型桩加固边坡较优的倾斜角度为60°;随着设桩位置离坡顶距离的增加,边坡的稳定系数先增大后减小,当设桩位置距坡顶的相对位置为0.58~0.66,边坡的稳定系数较高;当桩排距为9倍桩径,边坡的稳定系数较高。研究结果为倾斜微型桩的设计与工程应用提供了理论依据,具有一定的普遍意义。     

Investigation on the process parameters of TIG-welded aluminum alloy through mechanical and microstructural characterization

Multi-pass TIG welding was conducted on plates (15×300×180 mm3) of aluminum alloy Al-5083 that usually serves as the component material in structural applications such as cryogenics and chemical processing industries. Porosity formation and solidification cracking are the most common defects when TIG welding Al-5083 alloy, which is sensitive to the welding heat input. In the experiment, the heat input was varied from 0.89 kJ/mm to 5 kJ/mm designed by the combination of welding torch travel speed and welding current. Tensile, micro-Vicker hardness and Charpy impact tests were executed to witness the impetus response of heat input on the mechanical properties of the joints. Radiographic inspection was performed to assess the joint's quality and welding defects. The results show that all the specimens displayed inferior mechanical properties as compared to the base alloy. It was established that porosity was progressively abridged by the increase of heat input. The results also clinched that the use of me-dium heat input (1-2 kJ/mm) offered the best mechanical properties by eradicating welding defects, in which only about 18.26% of strength was lost. The yield strength of all the welded specimens remained unaffected indicated no influence of heat input. Partially melted zone (PMZ) width also affected by heat input, which became widened with the increase of heat input. The grain size of PMZ was found to be coarser than the respective grain size in the fusion zone. Charpy impact testing revealed that the absorbed energy by low heat input specimen (welded at high speed) was greater than that of high heat input (welded at low speed) because of low porosity and the formation of equiaxed grains which induce better impact toughness. Cryogenic (-196 C) impact testing was also performed and the results corroborate that impact properties under the cryogenic environment revealed no appreciable change after welding at designated heat input. Finally, Macro and micro fractured surfaces of tensile and impact specimens were analyzed using Stereo and Scanning Electron Microscopy (SEM), which have supported the experimental findings.     

基于动力学仿真的6×6轮式越野车辆总体性能评价

为分析和评价某型6×6轮式越野车辆的总体设计性能,建立了整车多刚体动力学模型、刚柔耦合动力学模型以及悬架系统台架试验模型,计算了整车固有特性,依次进行了悬架系统运动学、行驶动力学、操纵稳定性分析。在计算车体和悬架摆臂结构模态的基础上,考核了典型行驶工况下车体和悬架部件结构的动态强度,依据国家相关标准,利用仿真结果对6×6整车设计进行了系统的评价,指出了该越野车总体设计性能的不足,为其进一步改进和优化设计提供了参考依据。研究方法对其他轮式越野车辆系统的设计和评价具有一定的参考价值。     

U型BFRP箍筋试件受剪试验分析

针对U型箍筋抗剪试验缺乏强度折减实践依据的问题,设计15个配有BFRP箍筋的C30混凝土U型试件。在BFRP箍筋两侧用套筒将其锚固,弯折成U型,箍筋两端采用穿心千斤顶施加荷载,逐渐加载至BFRP箍筋破坏。通过分析试验数据,建立试件受力模型,可知弯折部位锚固长度对BFRP箍筋强度折减有较大影响,最大折减为原强度的65%;随着锚固长度的增加,BFRP箍筋强度呈线性增加至某个定值;最后推导出U型BFRP箍筋强度折减公式。     

等离子体天线辐射特性研究

用环形荧光灯制作了两幅等离子体天线,等离子体激励源分别为220 V交流电压和射频信号.测量了两种等离子体天线的电压驻波比和远区辐射场强,并与周长相同的方框金属天线的特性进行了对比.结果表明,等离子体天线的增益较金属天线平均低5 dB左右;在试验频率低端,220 V电源预激励方式下等离子体天线增益比RF直接激励要高2～4 dB,随着频率增加,两者增益差变小.     

内置式耐压液舱实肋板拓扑优化设计方案分析

通过对内置式耐压液舱中实肋板开孔拓扑优化设计后的强度和稳定性分析发现，对于周向范围为162°的内置式耐压液舱，实肋板在中内龙骨附近开孔较优。实肋板开孔后对于其本身的稳定性影响不大，但MISES应力会有所变化；实肋板开孔后，液舱结构的稳定性会稍微降低，后期在进行液舱结构设计时要考虑是否加强。     

随机-非概率模型下的船体结构屈服强度可靠性分析

针对在役舰船船体载荷、材料属性的随机特性和实船勘验得出的腐蚀损伤下船体抗力区间特性,提出一种基于随机概率理论和区间非概率理论的随机-非概率可靠性分析模型,分别从区间变量随机化和随机变量区间化两个角度给出该模型的可靠性指标求解方法。基于该模型对某舰船船体结构屈服强度进行可靠性分析,结果表明:该模型既体现了结构变量的客观不确定性又减弱了评估结果的盲目保守性,对于既含有随机变量又含有区间变量的在役舰船的可靠性评估具有很强的适用性。     

化学键合胶凝材料抗硫酸盐侵蚀性能

采用浸-烘循环的方法模拟干湿循环交替环境进行新型化学键合胶凝材料抗硫酸盐加速侵蚀试验.侵蚀溶液为质量浓度为5％的硫酸钠溶液,一组试验采用全浸-烘循环,另一组试验采用半浸-烘循环.在经受30×N(N=1,2,3,4,5)次循环后,测定试件的强度耐蚀系数和质量损失率,以此评价化学键合胶凝材料抗硫酸盐侵蚀性能.试验结果表明:半浸-烘循环的侵蚀比全浸-烘循环的侵蚀严重;在经受150次侵蚀循环后,试件外观无严重破损,质量不减反增,强度也不降低,说明化学键合胶凝材料具有优良的抗硫酸盐侵蚀性能.