穿甲子弹垂直侵彻防弹钢试验与理论模型

试验研究了穿甲子弹垂直侵彻高强防弹钢的机理,提出了一个分析靶板极限速度和弹体剩余速度的理论模型,该模型综合考虑了材料的应变率与热软化效应,结果表明,理论值与试验值吻合很好.分析了失效准则的影响,研究了剪切带温度和靶板耗能随入射速度的变化规律.     

破片模拟弹侵彻钢板的有限元分析

根据破片模拟弹侵彻钢板的实验研究,采用MSC.Dytran对破片模拟弹侵彻钢板的侵彻过程、侵彻特性、钢板的破坏模式以及弹体的侵彻速度、靶板的侵彻阻力进行了有限元分析,并将分析结果与实验结果进行了比较.分析结果表明,破片模拟弹冲击钢装甲的侵彻过程可大致分为初始接触、弹体侵入、剪切冲塞和穿甲破坏4个阶段.有限元分析的破片模拟弹侵彻特性及靶板破坏模式与实验观测结果有较好的一致性,在靶板破口的正面,与弹体平面凸缘两端接触的部分,变形以剪切为主,而与切削面接触的部分,以挤压变形为主;靶板破口背面为剪切冲塞破坏;有限元模拟的弹体剩余速度与实验结果吻合较好,弹体侵彻过程中弹靶作用界面的速度和侵彻速度近似呈线性变化.有限元分析结果还表明,采用适当的模型,有限元法能较好地模拟破片模拟弹侵彻钢板的侵彻过程、侵彻特性以及钢板的破坏模式.     

陶瓷基复合装甲防12.7mm穿甲燃烧弹的靶试研究（Ⅰ）

基于对材料特性和防弹机理的认识,设计了由Al2O3陶瓷、616装甲钢和高强PE材料构成的陶瓷基复合装甲板,并用现役127.mm穿甲燃烧弹进行靶试考核,检验靶板设计思路,结果表明：防护面密度为128 kg/m2的靶板可防住该弹。     

Chain damage effects of multi-spaced plates by reactive jet impact

Chain damage is a new phenomenon that occurs when a reactive jet impacts and penetrates multi-spaced plates.The reactive jet produces mechanical perforations on the spaced plates by its kinetic energy(KE),and then results in unusual chain rupturing effects and excessive structural damage on the spaced plates by its deflagration reaction.In the present study,the chain damage behavior is initially demonstrated by experiments.The reactive liners,composed of 26 wt％Al and 74 wt％PTFE,are fabricated through a pressing and sintering process.Three reactive liner thicknesses of 0.08 CD,0.10 CD and 0.12 CD(charge diameter)are chosen to carry out the chain damage experiments.The results show a chain rupturing phenomenon caused by reactive jet.The constant reaction delay time and the different penetration velocities of reactive jets from liners with different thicknesses result in the variation of the deflagration position,which consequently determines the number of ruptured plates behind the armor.Then,the finite-element code AUTODYN-3D has been used to simulate the kinetic energy only-induced rupturing effects on plates,based on the mechanism of behind armor debris(BAD).The significant discrepancies between simulations and experiments indicate that one enhanced damage mechanism,the behind armor blast(BAB),has acted on the ruptured plates.Finally,a theoretical model is used to consider the BAB-induced enhancement,and the analysis shows that the rupturing area on aluminum plates depends strongly upon the KE only-induced pre-perforations,the mass of reactive materials,and the thickness of plates.     

陶瓷基装甲抗枪弹机理研究现状

从陶瓷基装甲的特点出发,介绍了其抗弹性能的评定指标,讨论了弹靶撞击过程的划分,重点评述了抗弹机理的研究方法和陶瓷基装甲的耗能机制;并总结了影响陶瓷基装甲抗枪弹性能的4个主要因素:陶瓷厚度、约束条件、弹丸形状和撞击速度.     

子母式穿甲弹子弹发射过程研究

对子母式穿甲弹子弹的发射过程进行详细的分析,得出了子弹长度与子弹飞离母弹速度的关系、子弹长度与火药燃烧率的关系、子弹长度与母弹弹头部发射孔内最大压力的关系以及子弹的长度与子弹发射所需时间的关系,为子母式穿甲弹设计提供了依据。     

横向运动板干扰聚能射流的数值模拟

基于有限元分析软件ANSYS/LS-DYNA和LS-PREPOST,用ALE算法对射流垂直侵彻横向运动防护板的过程进行模拟分析。防护板在不同速度下干扰射流时,对防护板和后效板上的开坑形状进行分析,并计算后效板上的最终侵深及射流轴线上的速度降,得到射流在横向防护板作用下后效板侵深及射流轴线上的速度降随防护板速度变化的曲线。结果表明,防护板抗射流侵彻能力随防护板速度的增加而增强,尤其是防护板横向速度在0～100m/s增加时,抗射流侵彻能力增强较为明显。     

Damage visualization and deformation measurement in glass laminates during projectile penetration

Transparent armor consists of glass-polymer laminates in most cases. The formation and propagation of damage in the different glass layers has a strong influence on the ballistic resistance of such laminates. In order to clarify the course of events during projectile penetration, an experimental technique was developed, which allows visualizing the onset and propagation of damage in each single layer of the laminate. A telecentric objective lens was used together with a microsecond video camera that allows recording 100 frames at a maximum rate of 1 MHz in a backlit photography set-up. With this technique, the damage evolution could be visualized in glass laminates consisting of four glass layers with lateral dimensions 500 mm × 500 mm. Damage evolution was recorded during penetration of 7.62 mm AP projectiles with tungsten carbide core and a total mass of 11.1 g in the impact velocity range from 800 to 880 m/s. In order to measure the deformation of single glass plates within the laminates, a piece of reflecting tape was attached to the corresponding glass plate, and photonic Doppler velocimetry (PDV) was applied. With the photonic Doppler velocimeter, an infrared laser is used to illuminate an object to be measured and the Doppler-shifted light is superimposed to a reference light beam at the detector. The simultaneous visualization and PDV measurement of the glass deformation allow determining the deformation at the time of the onset of fracture. The analysis of the experimental data was supported by numerical simulations, using the AUTODYN commercial hydro-code.     

A case study in bio-inspired engineering design: defense applications of exoskeletal sensors

As part of a bio-inspired design process, the authors examine exoskeletal sensors found in insects and their potential application to armor and hardened buildings. In this way, the outer hardening of a structure or vehicle would not limit the ability of occupants to arrive at an actionable picture of the outer environment. To this end, various sensor modalities employed by insects are compared and contrasted with their current human-engineered equivalents. In several sensing modalities, biosensors perform better, are smaller, and more energy efficient than human-engineered equivalents. They note that biological designs tend to employ non-linear response to signal amplitude and respond with heightened sensitivity over a greater dynamic range of signals than human-engineered sensors. The insect biological sensors have structural and mechanical innovations that preserve the protective capacity of the exoskeleton.     

采用遗传算法的弹托迎风窝结构设计

针对一体化弹丸弹托易分离性和轻质化的设计要求，构建弹托迎风窝参数化外形模型，基于激波和膨胀波理论建立弹托气动力计算模型；以弹托分离加速度和弹托质量综合最优为目标函数，采用遗传算法对弹托迎风窝的外形参数进行优化设计，从而得到弹托迎风窝的优化外形。以中口径尾翼稳定脱壳穿甲弹的弹托设计为例，采用提出的优化设计模型对其迎风窝结构进行优化设计，并采用基于动网格技术的弹托分离仿真模型验证其最优性。仿真结果表明：所提优化模型能够得到最优的弹托迎风窝结构；针对现有的中口径尾翼稳定脱壳穿甲弹，可进一步对其弹托结构进行优化，以提高其分离快速性。