Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

空化射流实验研究

空化水射流技术是将空化作用引入到高压水射流而形成的一种新型高压水射流技术，在同等条件下，空化射流相对于普通高压水射流具有破碎和切割能力更高的特点。通过数值模拟和实验方法对空化技术进行研究，进行了喷嘴流场的数值模拟计算，设计了空化射流实验装置及空化喷嘴。以生锈铁板为研究对象，分别进行了喷嘴型号、打击时间、入口压力、靶距和扩散段长度的空化射流打击效果对比实验，研究了空化参数对空化效果的影响。实验结果表明角形喷嘴进行淹没射流的空化效果较好，空化射流除锈具有最优打击时间。不同的入口压力对应不同的最佳靶距。     

聚能射流形成过程的理论建模与分析

分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。     

单兵火箭燃气射流噪声抑制的实验研究

为了能够有效抑制单兵火箭发射时的燃气射流噪声,设计了液体水圆柱形平衡体安置在火箭发动机后面,对平衡体降噪进行实验研究。在实验中利用压电式传感器测得了发射筒周围的冲击波超压值,与没加液体水平衡体实验测得的超压值相比较,发现放液体水平衡体时在改进发动机推力性能的同时,降低了整个观测区域的噪声,尤其是射流上游,起到了显著的降噪效果,并分析了火箭燃气射流与液体水平衡体相互作用的机理。实验结果对单兵火箭发射的噪声防护问题研究提供了科学依据。     

Chain damage effects of multi-spaced plates by reactive jet impact

Chain damage is a new phenomenon that occurs when a reactive jet impacts and penetrates multi-spaced plates.The reactive jet produces mechanical perforations on the spaced plates by its kinetic energy(KE),and then results in unusual chain rupturing effects and excessive structural damage on the spaced plates by its deflagration reaction.In the present study,the chain damage behavior is initially demonstrated by experiments.The reactive liners,composed of 26 wt％Al and 74 wt％PTFE,are fabricated through a pressing and sintering process.Three reactive liner thicknesses of 0.08 CD,0.10 CD and 0.12 CD(charge diameter)are chosen to carry out the chain damage experiments.The results show a chain rupturing phenomenon caused by reactive jet.The constant reaction delay time and the different penetration velocities of reactive jets from liners with different thicknesses result in the variation of the deflagration position,which consequently determines the number of ruptured plates behind the armor.Then,the finite-element code AUTODYN-3D has been used to simulate the kinetic energy only-induced rupturing effects on plates,based on the mechanism of behind armor debris(BAD).The significant discrepancies between simulations and experiments indicate that one enhanced damage mechanism,the behind armor blast(BAB),has acted on the ruptured plates.Finally,a theoretical model is used to consider the BAB-induced enhancement,and the analysis shows that the rupturing area on aluminum plates depends strongly upon the KE only-induced pre-perforations,the mass of reactive materials,and the thickness of plates.     

Theoretical and numerical simulation study on jet formation and penetration of different liner structures driven by electromagnetic pressure

The use of a shaped liner driven by electromagnetic force is a new means of forming jets. To study the mechanism of jet formation driven by electromagnetic force, we considered the current skin effect and the characteristics of electromagnetic loading and established a coupling model of"Electric—Magnetic—Force"and the theoretical model of jet formation under electromagnetic force. The jet formation and penetration of conical and trumpet liners have been calculated. Then, a numerical simulation of liner collapse under electromagnetic force, jet generation, and the stretching motion were performed using an ANSYS multiphysics processor. The calculated jet velocity, jet shape, and depth of penetration were consistent with the experimental results, with a relative error of less than 10％. In addition, we calculated the jet formation of different curvature trumpet liners driven by the same loading condition and ob-tained the influence rule of the curvature of the liner on jet formation. Results show that the theoretical model and the ANSYS multiphysics numerical method can effectively calculate the jet formation of liners driven by electromagnetic force, and in a certain range, the greater the curvature of the liner is, the greater the jet velocity is.     

Investigate the effects of magnetic fields on the penetration ability of a shaped charge jet at different standoffs

The influence of a magnetic field on the stability of a shaped charge jet is experimentally investigated at standoffs of 490, 650 and 800 mm. The experimental results without and with the magnetic field are compared in terms of the shaped charge jet form, stability and penetration ability. A theoretical model based on one-dimension fluid dynamics is then developed to assess the depth of penetration of the shaped charge at those three standoffs and magnetic conditions. The results show that the penetration capability can be enhanced in more than 70% by the magnetic field. The theoretical calculations are compared with the experimental results with reasonably good correlation. In addition, the parameters introduced in the theory are discussed together with the experiments at three standoffs studied.     

采用射流掺混增强的前可调面积涵道引射器数值模拟

为了提高风扇外涵和核心机驱动风扇级外涵流体的掺混效率，提出一种采用射流掺混增强的前可调面积引射器设计方案。通过数值模拟的手段对流量特性、流动掺混和总压损失等方面进行了研究，并同基准模型进行了对比分析，结果表明：采用波瓣混合器结构的前可调面积引射器设计，显著地增加了较高出口背压工况下风扇外涵的流通能力；新的设计方案不仅没有增加低出口背压工况下的总压损失，还减小了高背压出口工况下的流动损失；流向涡的特征尺度是提高掺混效率的关键，可以进一步优化波瓣混合器几何轮廓，以满足调节机构对结构设计的要求。     

横向运动板干扰聚能射流的数值模拟

基于有限元分析软件ANSYS/LS-DYNA和LS-PREPOST,用ALE算法对射流垂直侵彻横向运动防护板的过程进行模拟分析。防护板在不同速度下干扰射流时,对防护板和后效板上的开坑形状进行分析,并计算后效板上的最终侵深及射流轴线上的速度降,得到射流在横向防护板作用下后效板侵深及射流轴线上的速度降随防护板速度变化的曲线。结果表明,防护板抗射流侵彻能力随防护板速度的增加而增强,尤其是防护板横向速度在0～100m/s增加时,抗射流侵彻能力增强较为明显。     

超声辅助喷射电沉积Ni镀层的表面形貌及硬度

试验以直接超声方式,在喷射电沉积装置的基础上加载超声设备,分别在20℃和50℃两种镀液温度下在A3钢基体上制备了加载超声和不加载超声Ni镀层,研究了超声波及温度对Ni镀层表面形貌和硬度的影响。试验结果分析表明：在20℃条件下,超声可避免镀层裂纹的产生,提高镀层的硬度;在50℃条件下,超声可细化镀层的组织,且可显著提高镀层硬度;超声波对喷射电沉积层组织和性能的影响机理主要在于超声空化引起的析氢减少、细晶强化和加工硬度。