The building evacuation problem with shared information

In this article, the Building Evacuation Problem with Shared Information (BEPSI) is formulated as a mixed integer linear program, where the objective is to determine the set of routes along which to send evacuees (supply) from multiple locations throughout a building (sources) to the exits (sinks) such that the total time until all evacuees reach the exits is minimized. The formulation explicitly incorporates the constraints of shared information in providing online instructions to evacuees, ensuring that evacuees departing from an intermediate or source location at a mutual point in time receive common instructions. Arc travel time and capacity, as well as supply at the nodes, are permitted to vary with time and capacity is assumed to be recaptured over time. The BEPSI is shown to be NP‐hard. An exact technique based on Benders decomposition is proposed for its solution. Computational results from numerical experiments on a real‐world network representing a four‐story building are given. Results of experiments employing Benders cuts generated in solving a given problem instance as initial cuts in addressing an updated problem instance are also provided. © 2008 Wiley Periodicals, Inc. Naval Research Logistics, 2008     

Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

空化射流实验研究

空化水射流技术是将空化作用引入到高压水射流而形成的一种新型高压水射流技术，在同等条件下，空化射流相对于普通高压水射流具有破碎和切割能力更高的特点。通过数值模拟和实验方法对空化技术进行研究，进行了喷嘴流场的数值模拟计算，设计了空化射流实验装置及空化喷嘴。以生锈铁板为研究对象，分别进行了喷嘴型号、打击时间、入口压力、靶距和扩散段长度的空化射流打击效果对比实验，研究了空化参数对空化效果的影响。实验结果表明角形喷嘴进行淹没射流的空化效果较好，空化射流除锈具有最优打击时间。不同的入口压力对应不同的最佳靶距。     

狭长受限空间油气爆炸关键现象研究

以汽油油气混合物为研究对象,在狭长密闭管道中进行了油气爆炸实验,通过压阻式传感器测试爆炸过程中的压强信号,得到狭长受限空间中油气爆炸的基本参数。通过对实验结果的对比分析,发现狭长受限空间内的油气爆炸可以分为4个阶段：平滑加速阶段、湍流发展阶段、振荡激化阶段和余波阶段;一定强度的湍流流场可抑制链化学反应速度和火焰传播速度;振荡激化阶段发生在管道末端。为狭长密闭空间内油气爆炸的预防和抑爆技术研究提供了参考。     

The effects of model parameter deviations on the variance of a linearly filtered time series

We consider a general linear filtering operation on an autoregressive moving average (ARMA) time series. The variance of the filter output, which is an important quantity in many applications, is not known with certainty because it depends on the true ARMA parameters. We derive an expression for the sensitivity (i.e., the partial derivative) of the output variance with respect to deviations in the model parameters. The results provide insight into the robustness of many common statistical methods that are based on linear filtering and also yield approximate confidence intervals for the output variance. We discuss applications to time series forecasting, statistical process control, and automatic feedback control of industrial processes. © 2010 Wiley Periodicals, Inc. Naval Research Logistics, 2010     

运动潜体湍流尾迹的SAR遥感仿真研究

采用点源法获得密度层化海洋中运动潜体产生的速度场,使用计入海洋内部湍流对海表面毛细重力波作用的SAR遥感全谱模式,利用考虑内波混合的湍流k-ε模式,并且使用Nasmyth海洋普适谱,建立了运动潜体湍流尾迹的SAR遥感仿真模型.利用该仿真模型对Rankine卵形体的湍流尾迹进行了仿真分析,获得令人满意的结果.     

(修，2撤3)关键几何参数对超声速膨胀器流场和性能影响的数值研究

为了揭示关键几何参数对超声速膨胀器流动特性影响的规律,对3种隔板安装角和5种出进口面积比超声速膨胀器设计工况下的流场进行了数值研究。结果表明：随隔板安装角增加,斜激波向出口迁移,斜激波强度略有降低,超声速膨胀器膨胀比减小,效率提高;随出进口面积比增加,流道内高速区显著扩大并逐渐靠近压力面,斜激波增强,出口流动损失增加,超声速膨胀器膨胀比增大,效率降低。为获得综合性能较优超声速膨胀器结构,需在较小出进口面积比和较大隔板安装角之间做折衷选择。     

聚能射流形成过程的理论建模与分析

分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。     

装备表面现代维修保养技术研究

结合装备表面智能维修保养技术方面的研究成果,介绍了装甲装备故障智能检测技术、自适应、自修复功能材料,装甲装备器材全自动保养设备等先进技术,侧重装备维修保养阐述了如何提高信息化程度,推进军队武器装备维修保养技术的现代化建设。     

基于不确定性理论的研制技术风险评估方法研究

分析了装备研制技术风险的含义,根据技术风险的特点建立了评价技术风险的指标体系。在技术风险度量中引入不确定性理论的概念,并建立了基于不确定性的技术风险的度量方法,对综合技术风险进行评价。最后通过实例验证了综合评价方法的可用性。