Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

聚能射流形成过程的理论建模与分析

分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。     

多爆炸成型弹丸性能参数灰关联分析

为了获得各参数对多爆炸成型弹丸毁伤性能的影响程度,以EFP速度和MEFP发散角为参考序列,以药型罩和装药参数为比较序列,运用灰关联理论对影响MEFP毁伤性能的参数进行了灰关联分析。在此基础上,应用灰关联分析结果完成了MEFP战斗部优化设计。结果表明:在较少样本空间前提下,采用灰关联理论可以分析获得影响多爆炸成型弹丸毁伤性能的各因素主次关系,而且经过优化后的MEFP战斗部,大大地提高了EFP的集聚性和毁伤性能。     

多孔材料药型罩聚能射流的形成条件

依据Herrmann状态方程和斜冲击波关系估算了多孔材料药型罩压垮之前的冲击温升,求解了经过冲击压缩卸载后材料的声速。给出了多孔材料药型罩聚能射流的形成条件。初始冲击温升会使材料的声速和强度降低,从而使多孔材料聚能射流形成射流的高速和低速条件降低。     

基于多信息的柴油机缸套磨损故障诊断研究

采用了模糊神经网络模型,对柴油机缸套磨损故障以及缸套破坏性磨损故障进行了诊断研究.通过缸套磨损故障的模拟实验,获取柴油机机身振动和铁谱分析等多源多维故障信息,并对融合故障信息进行预处理,解决了模糊神经网络输入矢量的模糊特性化、输出矢量的隶属函数及网络的学习训练问题,对缸套不同磨损故障进行了诊断.研究表明,这种基于多信息的诊断方法减小了故障诊断的不确定性,提高了诊断精度.     

A study on the surface overpressure distribution and formation of a double curvature liner under a two-point initiation

The formation mechanism of an EFP(explosively formed projectile) using a double curvature liner under the overpressure effect generated by a regular oblique reflection was investigated in this paper.Based on the detonation wave propagation theory,the change of the incident angle of the detonation wave collision at different positions and the distribution area of the overpressure on the surface of the liner were calculated.Three-dimensional numerical simulations of the formation process of the EFP with tail as well as the ability to penetrate 45# steel were performed using LS-DYNA software,and the EFP ve-locity,the penetration ability,and the forming were assessed via experiments and x-ray photographs.The experimental results coincides with those of the simulations.Results indicate that the collision of the detonation wave was controlled to be a regular oblique reflection acting on the liner by setting the di-mensions of the unit charge and maintaining the pressure at the collision point region at more than 2.4 times the CJ detonation when the incident angle approached the critical angle.The distance from the liner midline to the boundary of the area within which the pressure ratio of the regular oblique reflection pressure to the CJ detonation pressure was greater than 2.5,2,and 1.5was approximately 0.66 mm,1.32 mm,and 3.3 mm,respectively.It is noted that pressure gradient caused the liner to turn inside out in the middle to form the head of the EFP and close the two tails of the EFP at approximately 120μs.The penetration depth of the EFP into a 45# steel target exceeded 30 mm,and there was radial expansion between the head and tail of the EFE increasing the penetration resistance of the EFP.Therefore,the structural size of the unit charge and the liner can be further optimized to reduce resistance to increase the penetration ability of the EFP.     

Schedule design for liner services under vessel speed reduction incentive programs

Gas and particulate emissions from ship transportation have been increasing in recent years. In order to mitigate ship emissions near coastal areas, voluntary vessel speed reduction incentive programs (VSRIPs) were put in place by a number of ports. This paper studies a schedule design problem faced by liner shipping companies under VSRIPs. It proposes a mixed-integer nonlinear mathematical model for the minimization of the total cost, consisting of fuel cost, as well as operating cost, minus dockage refunds. The model balances three determinants, that is, the compliance of VSRIPs, the speed limit (the maximum physical speed of ships and the upper speed limit imposed by VSRIPs), and the limited number of ships. An enumerative algorithm and a piecewise-linear approximation algorithm are developed, based on some properties of the nonlinear model. The efficiency of the proposed algorithms is validated through extensive computational experiments.     

基于二人有限零和对策的防空兵火力分配方法

为了优化防空作战过程中火力分配问题,使射击达到最佳效果,运用对策论、线性规划等理论方法,采用对策矩阵建立了防空火力分配的线性规划模型,并通过计算示例和计算机仿真初步预测了敌方的空袭兵器使用情况和我方相应的兵力分配对策。该模型建立的防空火力分配方法较好地满足了要地防空装备的战术应用问题,对提高作战效能具有一定的参考价值。     

某地地导弹控制回路参数测试系统设计

针对导弹的定型试验,介绍了一种通用的地地导弹系统数据采集方案,并对其中所遇到的关键问题加以阐述,对各种火控系统的定型设备研制具有一定的参考价值     

Reaction characteristic of PTFE/Al/Cu/Pb composites and application in shaped charge liner

In this paper, the reaction characteristic and its application in shaped charge warhead of a novel reactive material, which introduced copper (Cu) and plumbum (Pb) into traditional polytetrafluoroethylene/aluminum (PTFE/Al), are studied. The thermal analysis and chemical reaction behavior of the PTFE/Al/Cu/Pb mixture are investigated by Differential Scanning Calorimetry (DSC),Thermo-gravimetry (TG), and X-ray Diffraction (XRD) techniques. Then, the shaped charge liners with PTFE/Al/Cu/Pb reactive materials are fabricated, and the X-ray experiments show that they could form reactive jets with excellent performance under the detonation effects of the shaped charge. Based on that, the penetration experiments of shaped charge with PTFE/Al/Cu/Pb reactive liner against steel plates are carried out, and the results demonstrate that the PTFE/Al/Cu/Pb reactive jets could produce a deeper penetration depth compared to the traditional PTFE/Al reactive jets. Meanwhile, the PTFE/Al/Cu/Pb reactive jets also show significant inner-blast effects, leading to dramatically cracking or fragmentation behavior of the penetrated steel plates. This new PTFE/Al/Cu/Pb reactive liner shaped charge presents enhanced penetration behavior for steel targets that incorporates the penetration capability of a high-density and ductility jet, and the chemical energy release of PTFE-matrix reactive materials.