内压作用下复合材料修复裂纹管道的失效分析

为准确评估在内压作用下纤维复合材料修复含裂纹管道的有效性及失效压力,建立复合材料修复后裂纹管道的失效数值模型。该数值模型通过扩展有限元法模拟管道裂纹的扩展,利用cohesive单元模拟胶层的脱粘失效,复合材料的失效通过最大应力失效准则进行判定。通过静水压爆裂试验对所提失效数值模型进行验证,实验结果与数值计算结果具有较好的一致性。失效数值分析结果表明:当内压增大至一定值后,未修复管道的初始裂纹沿轴向及壁厚方向逐渐扩展,进而使得管道内壁单元扩展成真实裂纹,此时真实裂纹贯穿整个壁厚方向,即认为裂纹管道发生爆裂失效,爆裂失效压力随初始裂纹半长呈指数形式下降。复合材料修复裂纹管道的不同修复工况呈现相同的失效模式:在单调递增的内压作用下,管道内表面首先出现黏结裂纹,而后其外表面裂纹张开趋势急剧上升,使得复合材料层应力急剧上升,达到极限强度而失效。且对于不同的初始裂纹尺寸,存在对应的复合材料缠绕层数临界值。     

Effect of operating temperature on aged single lap bonded joints

In recent decades, designers have increasingly focused on the stability of assemblies in composite materials over time, particularly when used in structural applications. The use of structural adhesives allows for realising assemblies without mechanical fasteners. In fact, bonding is an assembly technique that prevent corrosion, ensures uniform stresses in the joint, and grows the specific resistance of the assembly. The knowledge of the behaviour of bonded joint is necessary to ensure the reliability of this technique over time, especially in aggressive environments. The aim of this work consists in investigating the combined effect of hydrothermal ageing and temperature test on the lap shear strength of single lap joints realised in CFRP. The results showed a higher influence of the ageing on paste adhesive compared to film adhesive. However, the ageing, combined with the operating temperature, played a fundamental role on the shear strength of the bonded joints.     

Microstructure and pitting corrosion of armor grade AA7075 aluminum alloy friction stir weld nugget zone-Effect of post weld heat treatment and addition of boron carbide

Friction stir welding(FSW) of high strength aluminum alloys has been emerged as an alternative joining technique to avoid the problems during fusion welding.In recent times FSW is being used for armor grade AA7075 aluminum alloy in defense,aerospace and marine applications where it has to serve in non uniform loading and corrosive environments.Even though friction stir welds of AA7075 alloy possess better mechanical properties but suffer from poor corrosion resistance.The present work involves use of retrogression and reaging(RRA) post weld heat treatment to improve the corrosion resistance of welded joints of aluminum alloys.An attempt also has been made to change the chemical composition of the weld nugget by adding B4C nano particles with the aid of the FSW on a specially prepared base metal plate in butt position.The effects of peak aged condition(T6),RRA and addition of B4C nano particles on microstructure,hardness and pitting corrosion of nugget zone of the friction stir welds of AA7075 alloy have been studied.Even though RRA improved the pitting corrosion resistance,its hardness was slightly lost.Significant improvement in pitting corrosion resistance was achieved with addition of boron carbide powder and post weld heat treatment of RRA.     

新型航空铝合金材料复杂形貌点蚀损伤应力集中效应分析

根据7B04铝合金材料试件模拟加速点蚀试验检测结果,并结合铝合金材料点蚀行为机制、微观结构特征与随机性过程本质,构建由多个微观椭球体合成的楔入型与合围型两种典型复杂形貌点蚀损伤模型。采用ANSYS有限元方法建模并基于线弹性断裂力学,对上述两种点蚀损伤模型的应力集中效应进行计算与分析。研究发现:两种复杂形貌特征的点蚀损伤模型产生的应力集中系数数值基本相当,各个微观椭球体蚀坑分别对应力分布产生影响并相互干涉与叠加,造成复杂形貌点蚀损伤模型的应力集中系数数值增大;两种复杂形貌点蚀损伤模型的应力主要集中在各个微观椭球体蚀坑交会的位置,大都位于宏观点蚀损伤的侧边;两种复杂形貌点蚀损伤模型的应力集中效应作用区域的尺寸与铝合金材料微观晶粒尺寸、点蚀萌生的短裂纹初期尺寸基本相当。     

一种定征层状平面结构界面粘接强度的兰姆波方法

置于层状平面结构表面的斜劈超声换能器被用于激发和接收多模兰姆波。文章首先分析了采用多模兰姆波的幅频特性定征界面粘接强度的可行性。基于Ritec-SNAP 超声测量系统,建立了采用兰姆波方法定征层状结构界面粘接强度的实验系统。对于给定的层状平面结构,将粘接层的固化过程用于模拟粘接层界面强度的变化过程。对于不同的粘接层固化时间,实验测得的多模兰姆波幅频曲线明显不同。借助于声——超声技术中的应力波因子,给出了兰姆波应力波因子的定义。实验结果显示,兰姆波应力波因子与间接表示界面粘接强度的固化时间之间存在确定的单调对应关系,表明将多模兰姆波的应力波因子用于定征层状平面结构的界面粘接强度是可行的。     

2A12铝合金焊接接头超声冲击处理前后拉伸性能分析

为克服铝合金薄板焊接接头强度偏低、韧性不足的缺点,用ER5356焊丝对不同厚度的2A12铝合金板材进行了手工氩弧焊接,并采用超声冲击处理对焊接接头进行全覆盖强化处理。采用金相显微镜观察了处理和未处理焊接接头的显微组织结构,对接头的力学性能进行了测试分析,分析了超声冲击处理改善2A12铝合金焊接接头力学性能的机理。结果表明：铝合金焊接接头经超声冲击强化处理后,6 mm和4 mm厚板材对接接头的抗拉强度分别提高了17.4%和23.7%,延伸率分别提高了28%和44%,焊缝表层组织得到明显细化。分析认为：晶粒大幅细化、组织致密化和缺陷减少,是超声冲击处理改善铝合金焊接接头抗拉伸性能的主要原因。     

加速寿命试验下复合失效产品的可靠性评估

产品往往受随机失效和耗损失效两种模式的双重影响,通过构建复合寿命分布模型来表征这类产品失效规律。在加速寿命试验下,基于极大似然估计构造了该类产品寿命参数估计的数值算法;为了验证该寿命分布是否真服从假定的复合分布,构建了常应力等效失效数据的柯尔莫哥诺夫分布检验法;最后,以电连接器这一典型产品为例进行了工程仿真试验并进行数据评估,从而验证了评估方法的正确性。     

Stress corrosion cracking behaviour of gas tungsten arc welded super austenitic stainless steel joints

Super 304 H austenitic stainless steel with 3% of copper posses excellent creep strength and corrosion resistance, which is mainly used in heat exchanger tubing of the boiler. Heat exchangers are used in nuclear power plants and marine vehicles which are intended to operate in chloride rich offshore environment. Chloride stress corrosion cracking is the most likely life limiting failure with austenitic stainless steel tubing. Welding may worsen the stress corrosion cracking susceptibility of the material. Stress corrosion cracking susceptibility of Super 304 H parent metal and gas tungsten arc(GTA) welded joints were studied by constant load tests in 45% boiling Mg Cl2 solution. Stress corrosion cracking resistance of Super 304 H stainless steel was deteriorated by GTA welding due to the formation of susceptible microstructure in the HAZ of the weld joint and the residual stresses. The mechanism of cracking was found to be anodic path cracking, with transgranular nature of crack propagation. Linear relationships were derived to predict the time to failure by extrapolating the rate of steady state elongation.     

复合材料修补金属裂损结构吸湿老化的试验与有限元分析

暴露在湿热环境中的复合材料修补金属裂损结构易吸湿老化,导致该结构性能下降,服役寿命缩短。为研究吸湿性对复合材料修补金属裂损结构修补效果和耐久性的影响,利用试验方法分析了吸湿性对复合材料胶补金属裂损结构及胶黏剂力学性能的影响;利用有限元方法评估了吸湿性对复合材料胶补金属裂损结构试验件修补效果和耐久性的影响。研究结果表明:吸湿后含穿透双边裂纹铝合金板玻璃纤维单面胶补试验件的疲劳裂纹扩展寿命和极限载荷的平均值分别下降为吸湿前的71%和90%;吸湿造成拉伸条件下复合材料胶补金属裂损结构胶层失效模式由内聚破坏为主转变为界面破坏为主;在"湿-热"老化30天后,E44/聚酰胺环氧树脂胶黏剂试验件吸水饱和,弹性模量下降为未老化前的40%,塑性应变超过了总应变的25%;有限元分析发现胶层损伤受吸湿影响明显,吸湿性加速了胶层损伤,且裂纹长度越长,加速作用越明显;同时吸湿使得裂纹尖端的J积分值急剧增大,导致修补结构的疲劳裂纹扩展寿命缩短,裂纹长度越长,吸湿性对于复合材料胶接修补效果的危害越严重。     

Priori information analysis of optocoupler accelerated degradation experiment based on failure mechanism verification test

The optocoupler is a weak link in the inertial navigation platform of a kind of guided munitions. It is necessary to use accelerated storage test to verify the storage life of long storage products. Especially for small sample products, it is very important to obtain prior information for the design and implementation of accelerated degradation test. In this paper, the optocoupler failure mechanism verification test is designed and the experimental results are analyzed and the prior information is obtained. The results show that optocouplers have two failure modes, one is sudden failure and the other is degradation failure; the maximum temperature stress of optocoupler can't exceed 140 °C; the increase of leakage current of optocoupler is caused by movable ions contaminating the LED chip. The surface leakage current is proportional to the adsorption amount. The increase of leakage current makes p-n junction tunneling effect occur which LEDs the failure of the optocoupler. The lifetime distribution model of the optocoupler is determined by the failure physics. The lifetime of the optocoupler is subject to the lognormal distribution. The degeneracy orbit of the optocoupler leakage current is described by a power law model. The estimated values of the orbital parameters are initially calculated and the parameters of its life distribution function are deduced. The above information lays a good foundation for the optimization design and data processing of the accelerated degradation experiment.     

内腐蚀缺陷尺寸对DN150承插管线承压能力的影响

为了科学地指导DN150承插管线的使用与管理,采用非线性有限元法对带内腐蚀缺陷的DN150承插管线进行了剩余强度的评估。通过分析和计算,研究了腐蚀缺陷宽度、长度和深度对管线极限承载能力的影响。结果表明：腐蚀缺陷宽度对DN150承插管线的承载能力影响很小,可忽略不计;随着腐蚀缺陷长度的增加,管线的承载能力略微减小,当缺陷长度达到150mm,管道失效压力基本不变;随着腐蚀缺陷深度的增加,管道失效压力呈线性递减,其对管道失效压力的影响程度远远大于腐蚀缺陷长度。     

损伤铝合金表面超声焊接界面断口分析与结合机理

采用超声焊接铝合金箔材的工艺修复处理表面腐蚀受损的2A12CZ基体,并利用Quanta200型环境扫描电子显微镜分析了截面形貌及箔材与基体之间界面表面断口的微观形貌。结果表明：从截面来看,箔材与基体之间大部分发生了焊合,界面分界线大部分消失;从机械脱开的界面断口来看,其表面微观形貌表现为鳞片状及韧窝状的典型金属型断口形貌。这说明在给定条件下,焊接部位大部分呈冶金结合。最后对铝台金箔材与铝合金基体之间超声焊接机理进行了探讨。     

Φ2mm丝材电弧喷涂工艺对涂层结合强度的影响

分析了喷砂预处理和电弧喷涂这两个过程的工艺参数对涂层的结合强度的影响。将分数维理论用于喷砂后的试样表面,研究了喷砂角度、分数维和结合强度的相互关系,找到了获得最高结合强度所用的喷砂角度;通过正交试验法,找到了能获得最佳涂层结合强度的Φ2mm丝材电弧喷涂工艺参数。     

步进加速退化试验及其在电子产品可靠性评估中的应用

为快速评估具有高可靠、长寿命特点的电子产品的可靠性，提出了使用步进加速退化试验技术的方法。文中首先给出了步进加速退化的试验方法及基本假设，然后给出了步进退化数据向恒加退化数据的折算方法，在此基础上提出了基于伪失效寿命的步进加速退化可靠性评估算法，最后利用试验数据对该方法进行了验证。该方法与恒加退化试验相比，在保持样本量不变的基础上，可以极大地缩短试验时间，因此，具有更高的效费比。     

军用装备镁合金表面微弧氧化层SEM微观形貌及耐蚀性分析

利用微弧氧化技术的恒电流方式,在含有Na：SiO,和KF等电解质的溶液中制备了AZ91D镁合金微弧氧化层,通过扫描电镜观察分析及Cu加速盐雾腐蚀试验,研究了电解液中Na：SiO,和KF质量浓度对微弧氧化层结构及耐蚀性的影响。结果表明：在相同反应条件下,微弧氧化层厚度和表面粗糙度随Na：SiO,和KF质量浓度的增加而增加,微弧氧化层的耐蚀性取决于其表面粗糙度和厚度,粗糙度小、具有一定厚度的致密微弧氧化层耐蚀性好。     

激光制备多层结构的软质基底耐磨类金刚石膜

为提高金属铜软基底的耐磨、抗蚀能力，采用脉冲激光沉积技术制备了金属铜基底上的多层结构类金刚石保护膜；其中的碳化硅-类金刚石循环层避免了类金刚石膜层中内应力的累积，降低了功能类金刚石层破裂的风险，碳化硅持力层降低了软质铜基底与高硬度类金刚石层的硬度差，金属钛层则使得铜基底与上层碳化硅层牢固结合。实验测试表明，多层结构类金刚石保护膜在铜基底上附着牢固，可通过美军标MIL-48497A规定的重摩擦和国军标GJB150.5A-2009规定的高低温冲击试验，同时能够承受弱碱溶液的腐蚀；摩擦系数低、处于0.093以下，耐磨性能好、2 h摩擦未见磨痕。针对不同金属基底特性改进工艺，该技术可应用于存在腐蚀性环境中机械工具的抗磨保护膜。     

用聚电解质代替铬盐作磷化后处理剂的研究

用聚丙烯酸(PAA)和其它有机化合物复配,得到一种新型磷化后处理剂(CH41)。大量试验表明,其性能不低于含铬后处理剂,而且无毒,使用方便。作者利用电化学测试技术和SEM,EDX和XPS等表面分析手段,研究了它的作用机理。     

基于似然比检验的橡胶密封件加速试验机理一致性判别方法

加速退化试验广泛应用于橡胶密封件等长寿命产品的可靠性评估，试验过程中需要将高应力水平下的试验结果外推到正常应力水平。要获得准确的产品可靠性评估结果，需要保证加速应力下的退化失效机理与正常应力下的退化失效机理一致。基于似然比检验原理，提出加速退化试验机理一致性判别方法及流程。针对失效机理一致与失效机理变化两种场合，提出对数线性及非对数线性两类加速模型，并结合混合效应模型描述产品退化过程。利用似然比检验判断加速模型参数是否变化，完成失效机理一致性判别。仿真算例和应用实例表明，该方法能够有效判别橡胶密封件失效机理是否变化，并找到失效机理不变的应力水平边界。     

Pitting corrosion resistance and bond strength of stainless steel overlay by friction surfacing on high strength low alloy steel

Surface modification is essential for improving the service properties of components. Cladding is one of the most widely employed methods of surface modification. Friction surfacing is a candidate process for depositing the corrosion resistant coatings. Being a solid state process, it offers several advantages over conventional fusion based surfacing process. The aim of this work is to identify the relationship between the input variables and the process response and develop the predictive models that can be used in the design of new friction surfacing applications. In the current work, austenitic stainless steel AISI 304 was friction surfaced on high strength low alloy steel substrate. Friction surfacing parameters,such as mechtrode rotational speed, feed rate of substrate and axial force on mechtrode, play a major role in determining the pitting corrosion resistance and bond strength of friction surfaced coatings. Friction surfaced coating and base metal were tested for pitting corrosion by potentiodynamic polarization technique. Coating microstructure was characterized using optical microscopy, scanning electron microscopy and X-ray diffraction. Coatings in the as deposited condition exhibited strain-induced martensite in austenitic matrix. Pitting resistance of surfaced coatings was found to be much lower than that of mechtrode material and superior to that of substrate. A central composite design with three factors(mechtrode rotational speed, substrate traverse speed, axial load on mechtrode) and five levels was chosen to minimize the number of experimental conditions. Response surface methodology was used to develop the model. In the present work, an attempt has been made to develop a mathematical model to predict the pitting corrosion resistance and bond strength by incorporating the friction surfacing process parameters.     

TA2-B10管不同电偶腐蚀防护方式对B10管腐蚀特性的影响

为研究TA2-B10合金管在不同电偶腐蚀防护方式下对B10管腐蚀特性的影响,在青岛小麦岛海水试验场设置TA2-B10管直接连接、电绝缘连接、电绝缘＋涂层连接三组不同电偶腐蚀防护方式对照管道,依次进行1m/s、3m/s、4m/s流动海水与浸泡交替腐蚀试验。对试验后的三组B10管道线切割,通过管道内表面电位分布试验分析不同电偶腐蚀防护方式下B10管道的腐蚀类型;采用动电位极化曲线、电化学阻抗谱和微观表征,分析不同电偶腐蚀防护方式下距离法兰接头250mm处B10管试样的腐蚀特性。结果表明,直接连接TA2-B10管处于电偶腐蚀状态,B10端内电位正移腐蚀加速,电绝缘连接和绝缘＋涂层连接TA2-B10管均处于自腐蚀状态,但电绝缘＋涂层连接具有更好的绝缘效果;电绝缘＋涂层连接防护下的B10试样,腐蚀电流密度最小,自腐蚀电位最负;三组B10试样阻抗谱均呈现单容抗弧特征,电绝缘＋涂层连接防护下的B10试样具有更大的传递电阻和膜层电阻;电绝缘＋涂层连接能有效减缓点蚀、坑蚀和晶间腐蚀三种腐蚀倾向。以上结果综合说明,绝缘＋涂层防护方式具有更好的电偶腐蚀防护效果。