Pulsed current and dual pulse gas metal arc welding of grade AISI: 310S austenitic stainless steel

The transverse shrinkage, mechanical and metallurgical properties of AISI: 310 S ASS weld joints prepared by P-GMAW and DP-GMAW processes were investigated. It was observed that the use of the DP-GMAW process improves the aforementioned characteristics in comparison to that of the P-GMAW process. The enhanced quality of weld joints obtained with DP-GMAW process is primarily due to the combined effect of pulsed current and thermal pulsation(low frequency pulse). During the thermal pulsation period, there is a fluctuation of wire feed rate,which results in the further increase in welding current and the decrease in arc voltage. Because of this synchronization between welding current and arc voltage during the period of low frequency pulse, the DP-GMAW deposit introduces comparatively more thermal shock compared to the P-GMAW deposit, thereby reducing the heat input and improves the properties of weld joints.     

Comparative study on transverse shrinkage,mechanical and metallurgical properties of AA2219 aluminium weld joints prepared by gas tungsten arc and gas metal arc welding processes

Aluminium alloy AA2219 is a high strength alloy belonging to 2000 series. It has been widely used for aerospace applications, especially for construction of cryogenic fuel tank. However, arc welding of AA2219 material is very critical. The major problems that arise in arc welding of AA2219 are the adverse development of residual stresses and the re-distribution as well as dissolution of copper rich phase in the weld joint.These effects increase with increase in heat input. Thus, special attention was taken to especially thick section welding of AA2219-T87 aluminium alloy. Hence, the present work describes the 25 mm-thick AA2219-T87 aluminium alloy plate butt welded by GTAW and GMAW processes using multi-pass welding procedure in double V groove design. The transverse shrinkage, conventional mechanical and metallurgical properties of both the locations on weld joints were studied. It is observed that the fair copper rich cellular(CRC) network is on Side-A of both the weldments. Further, it is noticed that, the severity of weld thermal cycle near to the fusion line of HAZ is reduced due to low heat input in GTAW process which results in non dissolution of copper rich phase. Based on the mechanical and metallurgical properties it is inferred that GTAW process is used to improve the aforementioned characteristics of weld joints in comparison to GMAW process.     

Gas metal arc welding of high nitrogen stainless steel with Ar-N2-O2 ternary shielding gas

High nitrogen stainless steel with nitrogen content of 0.75％was welded by gas metal arc welding with Ar—N2-O2 ternary shielding gas. The effect of the ternary shielding gas on the retention and improvement of nitrogen content in the weld was identified. Surfacing test was conducted first to compare the ability of O2 and CO2 in prompting nitrogen dissolution. The nitrogen content of the surfacing metal with O2 is slightly higher than CO2. And then Ar—N2-O2 shielding gas was applied to weld high nitrogen stainless steel. After using N2-containing shielding gas, the nitrogen content of the weld was improved by 0.1 wt％. As N2 continued to increase, the increment of nitrogen content was not obvious, but the ferrite decreased from the top to the bottom. When the proportion of N2 reached 20％, a full austenitic weld was obtained and the tensile strength was improved by 8.7％. Combined with the results of surfacing test and welding test, it is concluded that the main effect of N2 is to inhibit the escape of nitrogen and suppress the ni-trogen diffusion from bottom to the top in the molten pool.     

Effect of fusion welding processes on tensile properties of armor grade,high thickness,non-heat treatable aluminium alloy joints

AA5059 is one of the high strength armor grade aluminium alloy that finds its applications in the military vehicles due to the higher resistance against the armor piercing (AP) threats. This study aimed at finding the best suitable process among the fusion welding processes such as gas tungsten arc welding (GTAW) and gas metal arc welding (GMAW) by evaluating the tensile properties of AA5059 aluminium alloy joints. The fracture path was identified by mapping the low hardness distribution profile (LHDP) across the weld cross section under tensile loading. Optical and scanning electron microscopies were used to characterize the microstructural features of the welded joints at various zones. It is evident from the results that GTAW joints showed superior tensile properties compared to GMAW joints and this is primarily owing to the presence of finer grains in the weld metal zone (WMZ) and narrow heat-affected zone (HAZ). The lower heat input associated with the GTAW process effectively reduced the size of the WMZ and HAZ compared to GMAW process. Lower heat input of GTAW process results in faster cooling rate which hinders the grain growth and reduces the evaporation of magnesium in weld metal compared to GMAW joints. The fracture surface of GTAW joint consists of more dimples than GMAW joints which is an indication that the GTAW joint possess improved ductility than GMAW joint.     

7A52铝合金便携式搅拌摩擦焊接头的组织与性能分析

采用便携式搅拌摩擦焊设备,对3mm厚的7A52铝合金薄板进行了焊接,对焊接头的显微组织和机械性能进行了观察测试。研究结果表明:焊接头可分为动态再结晶区、热-机影响区和母材3个区域,而没有明显的热影响区。动态再结晶区组织发生再结晶,生成细小的等轴晶粒;热-机影响区有塑性变形流线,且范围较窄;母材区保持着原来的轧制组织。接头硬度的最薄弱环节在热-机影响区。接头抗拉强度达到母材的70%左右,能够满足战场应急抢修的需求。     

Influence of tool pin profile on microstructure and corrosion behaviour of AA2219 Al-Cu alloy friction stir weld nuggets

To overcome the problems of fusion welding of aluminium alloys, the friction stir welding(FSW) is recognized as an alternative joining method to improve the mechanical and corrosion properties. Tool profile is one of the important variables which affect the performance of the FS weld. In the present work, the effect of tool profile on the weld nugget microstructure and pitting corrosion of AA2219 aluminium-copper alloy was studied. FSW of AA2219 alloy was carried out using five profiles, namely conical, square, triangle, pentagon and hexagon. The temperature measurements were made in the region adjacent to the rotating pin. It was observed that the peak temperature is more in hexagonal tool pin compared to the welds produced with other tool pin profiles. It is observed that the extensive deformation experienced at the nugget zone and the evolved microstructure strongly influences the hardness and corrosion properties of the joint during FSW. It was found that the microstructure changes like grain size, misorientation and precipitate dissolution during FSW influence the hardness and corrosion behaviour. Pitting corrosion resistance of friction stir welds of AA2219 was found to be better for hexagon profile tool compared to other profiles, which was attributed to material flow and strengthening precipitate morphology in nugget zone. Higher amount of heat generation in FS welds made with hexagonal profile tool may be the reason for greater dissolution of strengthening precipitates in nugget zone.     

雷诺数对沟槽减阻特性影响的数值分析

采用雷诺平均N-S方程和RNGk-ε湍流模型计算V型沟槽面的湍流边界层流动和黏性阻力,通过改变来流速度大小和沟槽面布置位置,研究了雷诺数对沟槽减阻特性的影响规律。计算结果表明,来流速度对沟槽减阻率的影响很大,对于一种尺度的V型沟槽,存在着一个具有较好减阻效果的来流速度范围,最大减阻率可达8.6%;沟槽面在沿来流方向上的布置位置对其减阻效果的影响则非常小。     

超声导波检测对接焊缝缺陷试验研究

应用超声导波技术快速扫查的特点对预制缺陷的焊缝进行检测试验，运用导波的直线和旋转角度扫描方式分别对12mm厚V型与16mm厚X型坡口对接焊缝中4种不同类型的缺陷进行探测。所采用的多功能超声检测设备的声定位装置对斜探头和缺陷位置定位。试验表明，在一定的条件下激励导波，能检出不同缺陷的位置和大小，检测结果直观，对实际焊缝缺陷检测具有指导意义。     

LD10cs 铝合金焊接接头疲劳裂纹扩展速率的研究

本文研究用表面裂纹法测试LD10cs铝合金板材焊接接头各部位疲劳裂纹扩展速率。结果表明:焊接接头各部位疲劳裂纹扩展速率随焊接热循环引起的金属组织变化而变化,有一定规律性。熔合线和焊趾处疲劳裂纹扩展速率较其他部位大。焊缝加强高的存在,引起焊趾处应力集中,使该处疲劳性能进一步恶化,成为焊接接头疲劳性能最差的部位。结合金相组织和扫描电镜分析,对影响焊接接头各部位疲劳裂纹扩展速率的各种因素作了较详细的探讨,并提出了改进焊缝质量的建议。     

Microstructure and pitting corrosion resistance of AA2219 Ale Cu alloy friction stir welds e Effect of tool profile

AA2219 Ale Cu alloy is widely used in defence and aerospace applications due to required combination of high strength-to-weight ratio and toughness.Fabrication of components used for defence always involves welding.Even though the mechanical properties of the base metal are better,but the alloy suffers from poor mechanical and corrosion properties during fusion welding.To overcome the problems of fusion welding,friction stir welding(FSW) is recognized as an alternative solid state joining method aimed to improve the mechanical and corrosion properties.Tool profile is one of the important variables which affect the performance of the friction stir weld.In the present work the effect of tool profile on the microstructure and pitting corrosion of AA2219 aluminiumecopper alloy was studied.Electron backscattered diffraction results established that the grain size and orientation of weld nugget of triangle profile is finer than that of conical profile.Differential scanning calorimetric results show the evidence of precipitate dissolution during FSW.It was found that the microstructure changes,such as grain size and its orientation precipitate dissolution during FSW influence the hardness and corrosion behaviour.Pitting corrosion resistance of friction stir welds of AA2219 was found to be better for triangle profile tool compared to conical profile which is attributed to material flow and strengthening precipitate morphology in various zones.Higher amount of heat generation during FSW made using triangle profile tool may be the reason for greater dissolution of strengthening precipitates in nugget zone and coarsening in thermo mechanically affected zone(TMAZ) and heat affected zone(HAZ).     

Multiobjective optimization of friction welding of UNS S32205 duplex stainless steel

The present study is to optimize the process parameters for friction welding of duplex stainless steel(DSS UNS S32205).Experiments were conducted according to central composite design.Process variables,as inputs of the neural network,included friction pressure,upsetting pressure,speed and burn-off length.Tensile strength and microhardness were selected as the outputs of the neural networks.The weld metals had higher hardness and tensile strength than the base material due to grain refinement which caused failures away from the joint interface during tensile testing.Due to shorter heating time,no secondary phase intermetallic precipitation was observed in the weld joint.A multi-layer perceptron neural network was established for modeling purpose.Five various training algorithms,belonging to three classes,namely gradient descent,genetic algorithm and LevenbergeM arquardt,were used to train artificial neural network.The optimization was carried out by using particle swarm optimization method.Confirmation test was carried out by setting the optimized parameters.In conformation test,maximum tensile strength and maximum hardness obtained are 822 MPa and 322 Hv,respectively.The metallurgical investigations revealed that base metal,partially deformed zone and weld zone maintain austenite/ferrite proportion of 50:50.     

Fabrication and analysis of TIG welding-brazing butt joints of in-situ TiB2/7050 composite and TA2

Lightweight hybrid structures of Al MMCs and titanium alloy dissimilar materials have great prospect in the defence industry application. So, it is necessary to join Al MMCs with Ti metal to achieve this structural design. In this work, in-situ TiB2/7050 composite and TA2 were firstly attempted to join by TIG welding-brazing technique. The result was that the intact welding-brazing butt joint was successfully fabricated. The joint presents dual characteristics, being a brazing on TA2 side and a welding on TiB2/7050 side. At brazing joint side, ER4043 filler metal effectively wets on TA2 under TIG heating condition, and a continuous interfacial reaction layer with 1—3μm is formed at welded metal/TA2 interface. The whole interfacial reaction layers are composed of Ti(AlSi)3 intermetallic compounds (IMCs), but their morphologies at the different regions present obvious distinguishes. The microhardness of the reaction layers is as much as 141—190 HV. At welding joints side, the fusion zone appears the equixaed crystal structure, and the grain sizes are much smaller than those of welded metal, which is attributed to the effect of TiB2 particulates from the melted TiB2/7050 on acceleration formation and inhibiting growth for the new crystal nucleus. The tensile test results show that average tensile strength of the optimal welding-brazing joint is able to achieve 138 MPa. The failure of the tensile joint occurs by quasi-cleavage pattern, and the cracks initiate from the IMCs layer at the groove surface of TA2 and propagate into the welded metal.     

Experimental investigation of Tie6Ale4V titanium alloy and 304L stainless steel friction welded with copper interlayer

The basic principle of friction welding is intermetallic bonding at the stage of super plasticity attained with self-generating heat due to friction and finishing at upset pressure. Now the dissimilar metal joints are especially popular in defense, aerospace, automobile, bio-medical,refinery and nuclear engineerings. In friction welding, some special alloys with dual phase are not joined successfully due to poor bonding strength. The alloy surfaces after bonding also have metallurgical changes in the line of interfacing. The reported research work in this area is scanty. Although the sound weld zone of direct bonding between Tie6Ale4 V and SS304 L was obtained though many trials, the joint was not successful. In this paper, the friction welding characteristics between Tie6Ale4 V and SS304 L into which pure oxygen free copper(OFC) was introduced as interlayer were investigated. Boxe Behnken design was used to minimize the number of experiments to be performed. The weld joint was analyzed for its mechanical strength. The highest tensile strength between Tie6Ale4 V and SS304 L between which pure copper was used as insert metal was acquired. Micro-structural analysis and elemental analysis were carried out by EDS, and the formation of intermetallic compound at the interface was identified by XRD analysis.     

Effect of welding processes on mechanical and microstructural characteristics of high strength low alloy naval grade steel joints

Naval grade high strength low alloy(HSLA) steels can be easily welded by all types of fusion welding processes. However, fusion welding of these steels leads to the problems such as cold cracking, residual stress, distortion and fatigue damage. These problems can be eliminated by solid state welding process such as friction stir welding(FSW). In this investigation, a comparative evaluation of mechanical(tensile, impact,hardness) properties and microstructural features of shielded metal arc(SMA), gas metal arc(GMA) and friction stir welded(FSW) naval grade HSLA steel joints was carried out. It was found that the use of FSW process eliminated the problems related to fusion welding processes and also resulted in the superior mechanical properties compared to GMA and SMA welded joints.     

Friction welding of AA6061 to AISI 4340 using silver interlayer

The present work pertains to the study on joining of AA6061 and AISI 4340 through continuous drive friction welding. The welds were evaluated by metallographic examination, X-ray diffraction, electron probe microanalysis, tensile test and microhardness. The study reveals that the presence of an intermetallic compound layer at the bonded interface exhibits poor tensile strength and elongation. Mg in AA6061 near to the interface is found to be favourable for the formation and growth of Fe2Al5 intermetallics. Introduction of silver as an interlayer through electroplating on AISI 4340 resulted in accumulation of Si at weld interface, replacing Mg at AA6061 side, thereby reducing the width of intermetallic compound layer and correspondingly increasing the tensile strength. Presence of silver at the interface results in partial replacement of Fe-Al based intermetallic compounds with Ag-Al based compounds. The presence of these intermetallics was confirmed by X-ray diffraction technique. Since Ag-Al phases are ductile in nature, tensile strength is not deteriorated and the silicon segregation at weld interface on AA6061 in the joints with silver interlayer acts as diffusion barrier for Fe and further avoids formation of Fe-Al based intermetallics. A maximum tensile strength of 240 MPa along with 4.9% elongation was obtained for the silver interlayer dissimilar metal welds. The observed trends in tensile properties and hardness were explained in relation to the microstructure.     

无电焊接中厚度钢板焊接接头的组织结构与性能研究

采用无电焊接方法对12mm厚度钢板进行了焊接。分析了满足中厚度钢板焊接能量要求的技术途径;利用SEM,EDS,XRD等手段观察、分析了焊缝的组织成分与显微结构;测试了焊接接头的拉伸强度、弯曲强度、显微硬度等力学性能。结果表明:在选择高放热体系基础上,通过增大焊接笔直径、减小反应物料粒径、提高压坯密度等方法,可以有效增大焊接热效率,从而满足中厚度钢板焊接能量需求;焊缝组织分为热影响区、熔合区与合金区,焊缝合金与母材间通过熔合区形成了冶金结合;焊接接头因固溶强化和析晶强化的作用,具有良好的力学性能,拉伸强度、平均显微硬度与弯曲强度分别为357MPa、186HV0.2与644MPa,达到了野战应急抢修技术要求。     

管道超声导波无损检测技术应用研究

利用研制的磁致伸缩超声导波无损检测装置对长直无缝钢管、舰用锅炉U型管和弯管进行了大量试验研究.研究发现,通过对该装置中磁致伸缩传感器的放置位置及方向进行适当调整,此装置即可在管道中激发纵向导波;该技术对管道壁厚减薄、磨损或腐蚀、裂纹、焊缝等缺陷同样具有检测能力;选择低频(20~40 kHz)激励脉冲信号有利于减少波的发散特性和提高缺陷的检测能力;导波在管道中传播衰减缓慢,适用于长距离、大范围、快速、非接触管道检测.     

Stress corrosion cracking behaviour of gas tungsten arc welded super austenitic stainless steel joints

Super 304 H austenitic stainless steel with 3% of copper posses excellent creep strength and corrosion resistance, which is mainly used in heat exchanger tubing of the boiler. Heat exchangers are used in nuclear power plants and marine vehicles which are intended to operate in chloride rich offshore environment. Chloride stress corrosion cracking is the most likely life limiting failure with austenitic stainless steel tubing. Welding may worsen the stress corrosion cracking susceptibility of the material. Stress corrosion cracking susceptibility of Super 304 H parent metal and gas tungsten arc(GTA) welded joints were studied by constant load tests in 45% boiling Mg Cl2 solution. Stress corrosion cracking resistance of Super 304 H stainless steel was deteriorated by GTA welding due to the formation of susceptible microstructure in the HAZ of the weld joint and the residual stresses. The mechanism of cracking was found to be anodic path cracking, with transgranular nature of crack propagation. Linear relationships were derived to predict the time to failure by extrapolating the rate of steady state elongation.     

焊接工艺对GMAW堆焊焊缝区温度场影响的数值模拟

为了探索焊接工艺对熔化极气体保护堆焊快速成形零件组织性能的影响，根据材料热物理性能参数以及相变潜热与温度的非线性关系，建立了熔化极气体保护堆焊成形过程的数学模型和有限元模型，利用ANSYS软件的APDL语言编写程序，实现了高斯移动热源载荷下的熔化极气体保护堆焊成形温度场计算，分析对比了不同焊接工艺对焊缝区温度场热循环的影响。结果表明：在其他因素一定的条件下，热输入和焊接速度对焊缝区热循环影响显著，而基板厚度对其影响较小；选择厚度约为16mm的基板，采用小于120×20J的热输入和大于10mm／s的焊接速度有望成形出性能优良的零件。     

Fracture mechanism of a cylindrical shell cut by circumferential detonation collision

The failure mechanism of a cylindrical shell cut into fragments by circumferential detonation collision was experimentally and numerically investigated. A self-designed detonation wave regulator was used to control the detonation and cut the shell. It was found that the self-designed regulator controlled the fragment shape. The macrostructure and micro-characteristics of fragments revealed that shear fracture was a prior mechanism, the shell fractured not only at the position of detonation collision, but the crack also penetrated the shell at the first contact position of the Chapmen-Jouguet (C-J) wave. The effects of groove number and outer layer thickness on the fracture behavior were tested by simulations. When the thickness of the outer layer was 5–18 mm, it has little effect on fragmentation of the shell, and shells all fractured at similar positions. The increase of the groove number reduced the fracture possibility of the first contact position of the C-J wave. When the groove number reached 7 with a 10 mm outer layer (1/4 model), the fracture only occurred at the position of detonation collision and the fragment width rebounded.