Direct ink writing of 3D-Honeycombed CL-20 structures with low critical size

3D-Honeycombed CL-20 structures with low critical size of detonation have been fabricated successfully for intelligent weapon systems using a micro-flow direct ink writing (DIW) technology. The CL-20-based explosive ink for DIW technology was prepared by a two-component adhesive system with waterborne polyurethane (WPU) and ethyl cellulose (EC). Not only the preparation of the explosive ink but also the principle of DIW process have been investigated systematically. The explosive ink displayed strong shear-thinning behavior that permitted layer-by-layer deposition from a fine nozzle onto a substrate to produce complex shapes. The EC content was varied to alter the pore structure distribution and rheological behavior of ink samples after curing. The deposited explosive composite materials are of a honeycombed structure with high porosity, and the pore size distribution increases with the increase of EC content. No phase change was observed during the preparation process. Both WPU and EC show good compatibility with CL-20 particles. Apparently high activation energy was realized in the CL-20-based composite ink compared with that of the refined CL-20 due to the presence of non-energetic but stable WPU. The detonation performance of the composite materials can be precisely controlled by an adjustment in the content of binders. The 3D honeycombed CL-20 structures, which are fabricated by DIW technology, have a very small critical detonation size of less than 69 μm, as demonstrated by wedge shaped charge test. The ink can be used to create 3D structures with complex geometries not possible with traditional manufacturing techniques, which presents a bright future for the development of intelligent weapon systems.     

Formation and characterization of core-shell CL-20/TNT composite prepared by spray-drying technique

The core-shell 2,4,6,8,10,12-Hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane/2,4,6-Trinitrotoluene (CL-20/TNT) composite was prepared by spray-drying method in which sensitive high energy explosive (CL-20) was coated with insensitive explosive (TNT). The structure and properties of different formulations of CL-20/TNT composite and CL-20/TNT mixture were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Laser particle size analyzer, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), differential scanning calorimetry (DSC), impact sensitivity test and detonation performance. The results of SEM, TEM, XPS and XRD show that ϵ-CL-20 particles are coated by TNT. When the ratio of CL-20/TNT is 75/25, core-shell structure is well formed, and thickness of the shell is about 20–30 nm. And the analysis of heat and impact show that with the increase of TNT content, the TNT coating on the core-shell composite material can not only catalyze the thermal decomposition of core material (CL-20), but also greatly reduce the impact sensitivity. Compared with the CL-20/TNT mixture (75/25) at the same ratio, the characteristic drop height of core-shell CL-20/TNT composite (75/25) increased by 47.6% and the TNT coating can accelerate the nuclear decomposition in the CL-20/TNT composites. Therefore, the preparation of the core-shell composites can be regarded as a unique means, by which the composites are characterized by controllable decomposition rate, high energy and excellent mechanical sensitivity and could be applied to propellants and other fields.     

Study of nano-nitramine explosives: preparation,sensitivity and application

Nano-nitramine explosives (RDX, HMX, CL-20) are produced on a bi-directional grinding mill. The scanning electron microscope (SEM) observations show that the prepared particles are semi-spherical, and the narrow size distributions are characterized using the laser particle size analyzer. Compared with the micron-sized samples, the nano-products show obvious decrease in friction and impact sensitivities. In the case of shock sensitivities, nano-products have lower values by 59.9% (RDX), 56.4% (HMX), and 58.1% (CL-20), respectively. When nano-RDX and nano-HMX are used in plastic bonded explosives (PBX) as alternative materials of micron-sized particles, their shock sensitivities are significantly decreased by 24.5% (RDX) and 22.9% (HMX), and their detonation velocities are increased by about 1.7%. Therefore, it is expected to promote the application of nano-nitramine explosives in PBXs and composite modified double-based propellants (CMDBs) so that some of their properties would be improved.     

Preparation and property of CL-20/BAMO-THF energetic nanocomposites

A sol-gel freezing-drying method was utilized to prepare energetic nanocomposites based on 2, 4, 6, 8, 10, 12-hexanitro-2, 4, 6, 8, 10, 12-hexaazaisowurtzitane (CL-20) with 3, 3-Bis (azidomethyl) oxetane-tetrahydrofuran copolymer (BAMO-THF) as energetic gel matrix. Scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman, Fourier-transform infrared spectroscopy (FT-IR) and differential thermal analyser (DTA) were utilized to characterize the structure and property of the resultant energetic nanocomposites. Compared with raw CL-20, the average particle sizes of CL-20 in CL-20/BAMO-THF energetic nanocomposites were decreased to nano scale and the morphologies of CL-20 were also changed from prismatic to spherical. FT-IR detection revealed that CL-20 particles were recrystallized in BAMO-THF gel matrix during the freezing-drying process. The thermal decomposition behaviors of the energetic nanocomposites were investigated as well. The thermolysis process of CL-20/BAMO-THF nanocomposites was enhanced and the activation energy was lower compared with that of raw CL-20, indicating that CL-20/BAMO-THF nanocomposites showed high thermolysis activity. The impact sensitivity tests indicated that CL-20/BAMO-THF energetic nanocomposites presented low sensitivity performance.     

Shock initiation performance of NTO-based polymer bonded explosive

3-nitro-1,2,4-tri-azol-5-one (NTO) is a high energy insensitive explosive. To study the shock initiation process of NTO-based polymer bonded explosive JEOL-1 (32%octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), 32% NTO, 28% Al and 8% binder system), the cylinder test, the gap experiments and numerical simulation were carried out. Firstly, we got the detonation velocity (7746 m/s) and the parameters of Jones-Wilkins-Lee (JWL) equation of state (EOS) for detonation product by cylinder test and numerical simulation. Secondly, the Hugoniot curve of unreacted explosive for JEOL-1 was obtained calculating the data of pressure and time at different Lagrangian positions. Then the JWL EOS of unreacted explosive was obtained by utilizing the Hugoniot curve as the reference curve. Finally, we got the pressure growth history of JEOL-1 under shock wave stimulation and the parameters of the ignition and growth reaction rate equation were obtained by the pressure-time curves measured by the shock-initiation gap experiment and numerical simulation. The determined trinomial ignition and growth model (IG model) parameters can be applied to subsequently simulation analysis and design of insensitive ammunition with NTO-based polymer bonded explosive.     

Performances and direct writing of CL-20 based ultraviolet curing explosive ink

A new type of explosive ink formulation that can be quickly cured was prepared with unsaturated polyester as binder,styrene as active monomer,2,4,6-trimethylbenzoyl-diphenylphosphine oxide as photoinitiator,and hexanitrohexaazaisowurtzitane (CL-20) as the main explosive.Then the explosive ink direct writing technology was used to charge the micro-sized energetic devices,the curing mechanism of the explosive ink was discussed,and the microstructure,safety performance and explosive transfer performance of the explosive ink molded samples were tested and analyzed.Results indicate that the composite material has a fast curing molding speed,its hardness can reach 2H within 8 min.The crystal form of CL-20 in the molded sample is still ε type.The CL-20 based W-curing explosive ink formulation has good compatibility,its apparent activation energy is increased by about 3.5 kJ/mol.The composite presents a significant reduction in impact sensitivity and its characteristic drop height can reach 39.8 cm,which is about 3 times higher than the raw material.When the line width of charge is 1.0 mm,the critical thickness of the explosion can reach 0.015 mm,and the explosion velocity is 7129 m/s when the charge density is 1.612 g/cm3.     

Preparation and characterization of HMX/NH2-GO composite with enhanced thermal safety and desensitization

To improve the safety of HMX, HMX/NH₂-GO composite was prepared with aqueous ammonia functionalized graphene oxide (NH₂-GO). The composite was characterized by SEM, Zeta potential, XPS, Raman spectrum, XRD, HPLC, DSC and BAM sensitivity test. The results indicated that the functionalization with aqueous ammonia can enhance the interaction between GO and HMX, and more efficiently desensitize the explosive. The optimal impact sensitivity of the HMX/NH₂-GO composite can be not less than 40 J, which is also the most insensitivity compared to the previous reports prepared by coating desensitization with non-energetic desensitized material. Moreover, the potential reason for the different impact and friction sensitivity was also discussed, which may bring a novel perspective to achieve the desensitization of energetic material.     

Theoretical design of new bridge-ring insensitive high energy compounds by selected normal Diels-Alder reactions between NH2-substituted oxazoles and NO2/NF2/NHNO2-substituted ethylenes/acetylenes

In this work, NH₂-substituted oxazoles and NO₂/NF₂/NHNO₂-substituted ethylenes/acetylenes were designed and used as dienes and dienophiles, respectively, in order to develop new bridge-ring insensitive high energy compounds through the Diels-Alder reaction between them. The reaction type, reaction feasibility and performance of reaction products were investigated in detail theoretically. The results showed that dienes most possibly react with dienophiles through the HOMO-diene controlled normal Diels-Alder reaction at relatively low energy barrier. Tetranitroethylene could react with the designed dienes much more easily than other dienophiles, and was employed to further design 29 new bridge-ring energetic compounds. Due to high heat of formation, density and oxygen balance, all designed bridge-ring energetic compounds have outstanding detonation performance, 16 of them have higher energy than HMX (1,3,5,7-tetranitro-1,3,5,7-tetrazocine) and 2 others even possess comparative energy with the representative of high energy compounds CL-20 (2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane). The predicted average h₅₀ value of these bridge-ring energetic compounds is 83 cm, showing their low impact sensitivity. The NH₂ groups could obviously impel the proceeding of Diels-Alder reactions, but would slightly decrease the energy and sensitivity performance. In all, the new designed bridge-ring compounds have both high energy and low sensitivity, and may be produced through Diels-Alder reactions at relatively low energy barrier. This paper may be helpful for the theoretical design and experiment synthesis of new advanced insensitive high energy compounds.     

Enhancing the explosive characteristics of a Semtex explosive by involving admixtures of BCHMX and HMX

A well-known ternary plastic explosive, Czech Semtex 1H, contains a mixture of PETN and RDX softened by SBR. In this work, BCHMX was used to replace PETN in Semtex 1H to form Sem-BC+RDX. In addition, another mixture based on BCHMX and HMX as energetic fillers bonded by the polymeric matrix of Semtex 1H (Sem-BC+HMX) was studied. The particle size distribution of each individual explosive was determined to obtain the optimum mixing conditions. Friction and impact sensitivities were determined. The velocity of detonation was reported practically and the detonation properties were calculated by EXPLO5 code. The explosive strength of each sample was measured by the ballistic mortar test. The conclusion confirms that the velocity of detonation of Sem-BC+HMX was the highest in comparison with the prepared samples. Sem-BC+RDX has the least impact and frictions sensitivities. Sem-BC+RDX has higher detonation velocity, detonation properties and explosive strength than Semtex 1H. Addition of BCHMX in Semtex 1H as a replacement for PETN is the candidate to produce a high performance advanced Czech plastic explosive.     

Preparation and characterization of HMX/EVA/hBNNSs micro-composites with improved thermal stability and reduced sensitivity

Hexagonal boron nitride nanosheets(HBNNSs)have huge potential in the field of coating materials owing to their remarkable chemical stability,mechanical strength and thermal conductivity.Thin-layer hBNNSs were obtained by a liquid-phase exfoliation of h-BN powders and incorporated into EVA coatings for improving the safety performance of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX).HBNNSs and ethylene-vinyl acetate copolymer(EVA)were introduced to HMX by a solvent-slurry process.For com-parison,the HMX/EVA and HMX/EVA/graphene(HMX/EVA/G)composites were also prepared by a similar process.The morphology,crystal form,surface element distribution,thermal decomposition property and impact sensitivity of HMX/EVA/hBNNSs composites were contrastively investigated.Results showed that as prepared HMX/EVA/hBNNSs composites were well coated with hBNNSs and EVA,and exhibited better thermal stability and lower impact sensitivity than that of HMX/EVA and HMX/EVA/G composites,suggesting superior performance of desensitization of hBNNSs in explosives.     

Effect of energy content of the nitraminic plastic bonded explosives on their performance and sensitivity characteristics

Information about the forty nine nitraminic plastic bonded explosives (PBXs) and different nitramines were collected. Fillers of these PBXs are nitramines 1,3,5-trinitro-1,3,5-triazinane (RDX) and β-1,3,5,7-tetranitro-1,3,5-tetrazocane (β-HMX), cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole (bicyclo-HMX, BCHMX) and ε-2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (ε-HNIW, CL-20) which are bonded by polyfluoro-elastomers, polydimethyl-siloxane, poly-glycidyl azide, polyisobutylene, polystyrene-butadiene, poly-acrylonitrile-butadiene and hydroxyl-terminated polybutadiene in addition to a melt cast compositions based on 2,4,6-trinitrotoluene. For thirty two of these PBXs the relationships are specified and analyzed between heats of their combustion and relative explosive strengths; by means of these relationships it might be possible to estimate, which groupings in the macromolecule of binder could be liable to their primary fission in the PBXs initiation. Similarly, for forty two of these explosives, the relationships are described and analyzed between their enthalpies of formation and impact sensitivities; here is especially attention paid to PBXs filled by BCHMX. Specific rate constants from Vacuum Stability Test (VST) of four nitramines and twenty PBXs are introduced into relationships with their enthalpies of formation. Regarding to all the mentioned cases, increasing of energy content of the studied explosives leads to increase of the relative explosive strength or initiation reactivity, respectively. Exception with the opposite trend, the outputs of VST are for BCHMX, where in PBXs are matrices with the esteric plasticizers or the energetic poly-glycidyl azide. Admixture of RDX or HMX, respectively, into the BCHX PBXs gives ternary PBXs whose thermal stability, in the sense of applied VST, is higher comparing to the original binary explosives.     

Sandwich structure for enhancing the interface reaction of hexanitrohexaazaisowurtzitane and nanoporous carbon scaffolds film to improve the thermal decomposition performance

Improving the thermal decomposition performance of hexanitrohexaazaisowurtzitane (CL-20) by appropriate methods is helpful to promote the combustion performance of CL-20-based solid propellants. In this study, we synthesized a sandwich structure of CL-20 and nanoporous carbon scaffolds film (NCS) and emphatically studied the thermal decomposition performance of the composite structure. Thermogravimetric analysis and differential scanning calorimetry were used to measure the thermal decomposition process of the composite structure. The kinetic parameters of thermal decomposition were calculated by the thermal dynamic analysis software AKTS. These results showed that the thermal decomposition performance of the sandwich structure of CL-20 and NCS was better than CL-20. Among the tested samples, NCS with a pore size of 15 nm had the best catalytic activity for the thermal decomposition of CL-20. Moreover, the thermal decomposition curve of the composite structure at the heating rate of 1 K/min was deconvoluted by mathematical method to study the thermal decomposition process. And a possible catalytic mechanism was proposed. The excellent thermal decomposition performance is due to the sandwich structure enhances the interface reaction of CL-20 and NCS. This work may promote the extensive use of CL-20 in the field of solid rocket propellant.     

Fabrication and characterization of mussel-inspired layer-by-layer assembled CL-20-based energetic films via micro-jet printing

Three-dimensional (3D) micro-jet printing is a droplet deposition technique based on liquid-phase materials. To improve the deposition density and performance of energetic films with micro/nanoscale on an energetic chip, polydopamine (PDA) was utilized as a linker bridge to induce the in-situ self-assembly of CL-20-based energetic film via 3D micro-jet printing. The self-assembly was extensively characterized by confocal laser scanning microscopy (CLSM), SEM, power-XRD, XPS, and DSC. The performance of the self-assembled film was verified by the mechanical properties and detonation properties, and a possible self-assembly mechanism in the layer-by-layer micro-jet printing process was proposed. The results indicated PDA-induced self-assembly enhanced the physical entanglement between the binders and energetic crystal, reduced the porosity from 15.87% to 11.28%, and improved the elastic modulus and the detonation performance of the CL-20-based energetic film. This work proposes a novel and promising energetic film design and fabrication strategy to enhance the interaction between the energetic composite layers in the micro-jet printing process.     

Insensitive energetic microspheres DAAF/RDX fabricated by facile molecular self-assembly

Insensitive energetic materials are promising in the defense weapons field. However, energetic materials still suffer from great challenges and the concern about their safety limits their utilization. In this work, insensitive energetic explosive 3,3′-diamino-4,4′-azoxyfurazan/hexahydro-1,3,5-trinitro-1,3,5-triazine (DAAF/RDX) microspheres were fabricated by self-assembly method. Rod-like DAAF/RDX was prepared by mechanical ball milling for comparison. DAAF/RDX composites with different mass ratios (90:10, 80:20, and 70:30) were obtained. The morphologies and structures of as-obtained DAAF/RDX composites were characterized by scanning electron microscopy (SEM), powder x-ray diffraction (PXRD) and fourier transform infrared spectroscopy (FT-IR). The results showed that DAAF/RDX microspheres exhibited regular shaped microspheres with sizes from 0.5 to 1.2 μm. There was no crystal transition during the modification process. The thermal properties of as-obtained materials were then evaluated by differential scanning calorimetry (DSC) and materials studio software. DAAF/RDX microspheres showed an advanced decomposition peak temperature compared with rod-like DAAF/RDX. The binding energy and peak temperature values at zero β_i (T_P0) of DAAF/RDX (90:10) increased by 36.77 kJ/mol, 1.6 °C, and 58.11 kJ/mol, 12.3 °C compared to DAAF/RDX (80:20) and DAAF/RDX (70:30), indicating the better thermal stability of DAAF/RDX (90:10). The characteristic drop height (H₅₀) of DAAF/RDX (higher than 100 cm) composites was higher than that of raw RDX (25 cm), suggesting significant improvements in mechanical safety. The preparation of DAAF/RDX microspheres is promising for the desensitization of RDX and useful for the formation of other materials and future wide applications.     

Burning characteristics of high density foamed GAP/CL-20 propellants

The monolithic foamed propellants with high densities were prepared by casting and two-step foaming processes. Glycidyl azide polymer (GAP) and isocyanate were used as the binder system and 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (HNIW, CL-20) was employed as the energetic component. The newly designed formulation containing 60 % CL-20 produced a force constant of 1077 J/g and low flame temperature of 2817 K. Two foamed propellants with densities of 1.32 g/cm³ and 1.53 g/cm³ were fabricated by a confined foaming process and examined by closed bomb tests. The results revealed that porosity significantly affects burning performance. A size effect on combustion behaviors was observed for the foamed propellant with 5.56 % porosity, and a double-hump progressive dynamic vivacity curve was obtained. At last, the 30 mm gun test was carried out to demonstrate the interior ballistic performance, and the muzzle velocity increased by 120 m/s at the same maximum chamber pressure when monolithic propellant was added in the charge.     

Scale-up synthesis and characterization of 2,6-diamino-3,5-dinitropyrazine-1-oxide

2,6-diamino-3,5-dinitropyrazine-1-oxide (ANPZO), as an insensitive high explosive, with a high yield and excellent purity has been prepared at pilot plant scale by an improved method. The synthesized ANPZO is characterized by IR, laser granularity measurement, SEM and HPLC. The particle analysis revealed that the improved method could offer desired product with average particle size of 40 μm and high purity (>98.45%). The experimental parameters exhibited that the detonation velocity of the formulation based on ANPZO was higher than that of the corresponding TATB formulation. The DSC curve showed that the exothermic decomposition of the product occurred at the temperature between 300.5 °C and 360.4 °C. Furthermore, the sensitivity test suggests its safe nature towards mechanical stimulus.     

现代灭火救援行动中安全隐患探析

以现代灭火救援行动中存在的安全隐患为切入口,归纳出爆燃、危险品、烟雾、高温、井坑池、电流和建筑物坍塌等七种主要威胁灭火人员安全的危险隐患,详细解析了这七种危险源形成原因和危害特点,并针对灭火救援行动,提出了相应的防范措施。     

两种单基发射药灌注成型为凝胶炸药研究

对14／7和22／1两种单基发射药灌注成型为凝胶炸药进行了初步的试验研究，并对生成的凝胶炸药进行了威力和猛度测试。结果表明，可以利用高分子含水材料与氧化剂将废弃的发射药转化为凝胶民用炸药，通过调整装药直径，可获得一定的威力和猛度。     

关于小尺寸装药用炸药薄膜的研究

利用真空蒸镀技术对太安炸药薄膜及其在小尺寸装药上的应用进行了研究。实验表明利用真空蒸镀技术可以研制出性能优良的炸药薄膜 ;红外光谱分析证明太安在蒸镀前后没有发生质的变化 ;扫描电镜分析得出了太安薄膜的微观结构 ;太安炸药薄膜在小尺寸装药上的应用表明了该装药具有可靠的传爆功能。     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.