凹腔上游横向喷流混合过程的实验研究

利用基于纳米粒子的平面激光散射(NPLS)技术研究了超燃冲压模型发动机中凹腔上游横向喷注乙烯燃料时凹腔附近的流场,主要研究了燃料射流与主流的混合过程;对比了在不同喷注压力下燃料射流穿透度的变化;研究了不同凹腔参数对燃料与主流混合过程的影响。通过研究发现,喷注压力对燃料射流与主流混合效果的影响主要体现在两个方面,射流的穿透度和射流的扩散;对燃料射流来说,与主流混合的主要阶段为大涡的形成直至破碎阶段;在喷注总压相同下,喷注位置靠近凹腔有利于燃料射流与主流的混合和向凹腔内的输运;凹腔构型对燃料射流的影响主要在于大尺度结构开始发展破碎的阶段。     

利用OH-PLIF技术显示超声速燃烧的火焰结构

针对在来流马赫数为1.72的空气来流中横向喷注氢气发生超声速燃烧的流场,利用平面激光诱导氢氧基荧光(OH-PLIF)技术,对超燃燃烧室中三个不同的流向截面进行了二维成像测量。选择波长为283.553nm的染料激光倍频光作为激发光,可近似认为获得的OH基荧光信号强度与OH基的摩尔分数成正比。瞬态的OH基PLIF图像揭示了超声速燃烧火焰结构具有高度湍流特性,在凹腔内部存在稳定的燃烧区,为整个燃烧反应提供值班火焰,起到了促进和稳定超声速燃烧的作用。超燃火焰在沿流向传播的同时还沿径向传播,凹腔展向尺度增大时火焰沿流向的火焰区会有所减小。     

超燃冲压发动机二维进气道多级多目标优化设计方法

提出了超燃冲压发动机二维进气道的多级多目标设计方法。选择总压恢复系数、压升比和阻力系数为性能目标,引入多级设计概念,分别基于一维气动力学分析方法和计算流体力学方法,采用混合遗传算法对4楔角外压和2楔角内压混合压缩进气道进行了多级多目标优化设计,得到了问题的Pareto非劣解集。采用上述方法可以提升超燃冲压发动机进气道的设计水平,得到高性能的设计方案。     

超燃冲压发动机燃烧室构型优化的试验研究

在直连式超燃冲压发动机试验系统上,通过调节超燃冲压发动机燃烧室壁面扩张角和燃料喷注位置,对燃烧室构型优化进行了试验研究。为了提高试验效率,燃烧室形面调节采用正交试验设计方法进行组织,每个形面进行5种喷注位置的试验,每次试验通过文氏管调节3个当量比的燃料流量。利用试验数据构造燃烧室性能关于构型参数的响应面模型,可用于燃烧室构型优化。通过两次渐进优化获得了性能更优的燃烧室构型,并根据试验数据分析了各构型参数对燃烧室性能的影响,结果表明:优化构型燃烧室的推力增益比基准构型增大了10.4%;燃烧室性能受各构型参数的强烈耦合影响。     

超燃冲压发动机燃烧室燃料喷注及其内流场的数值模拟

基于三维N-S方程,利用有限差分数值离散方法,对考虑了燃料喷注和凹腔结构综合影响的某超燃冲压发动机燃烧室模型的内流场进行了数值模拟,与实验流动图谱进行了定性比较,并进一步探讨了燃料喷注过程的非定常特性以及凹腔结构对流动的影响。研究表明:本文数值模拟的稳态时刻流场与实验流动图谱相似;数值结果捕捉到了横向喷注燃料沿下游运动并向凹腔扩散的非定常动态变化的规律。     

超燃冲压发动机的仿真与设计平台

高超声速飞行器所具有的全球实时侦察、快速部署和远程精确打击能力,将改变未来战争的作战方式,对国家安全产生战略性的影响.在高超声速的关键技术中,超燃冲压发动机技术占有极其重要的地住.本文分析了超燃冲压发动机的仿真与设计平台的研究、开发现状,并提出了超燃冲压发动机仿真设计技术所面临的挑战.     

超声速燃烧火焰放热区结构CH-PLIF成像技术

超燃冲压发动机是吸气式高超声速飞行器的关键部件之一，超燃冲压发动机燃烧室内火焰结构的研究对揭示超声速燃烧的稳焰机理具有重要意义。利用平面激光诱导荧光（Planar Laser-Induced Fluorescence，PLIF）技术测量了超声速燃烧直连式试验台燃烧过程中重要自由基CH的二维分布，实现了超声速燃烧火焰放热区结构的可视化。在开敞空间的低速射流火焰炉中使用甲烷/空气预混火焰对CH-PLIF技术进行了初步验证和系统优化，再利用CH-PLIF技术在凹腔稳焰的超燃直连台上实现了超声速燃烧火焰放热区结构的二维可视化，并与OH-PLIF和CH自发辐射测量结果进行了对比。实验结果表明，在开敞空间的低速射流预混火焰中，火焰放热区会发生扭曲、褶皱和分裂等现象，随着雷诺数的增大，火焰锋面褶皱程度更加显著；在凹腔稳焰的超声速燃烧中，火焰放热区高度褶皱和破碎，放热区结构的厚度为0.5～6.5 mm，同时也存在放热区的分裂与剥离等现象。CH-PLIF技术能够以较高的空间分辨率更准确地呈现凹腔超声速火焰放热区的结构，其在凹腔稳焰的超声速燃烧诊断中具有重要的应用价值。     

防务快讯

印度进行高超声速巡航技术研究目前,印度国防研究发展试验室正在进行高超声速技术演示飞行器(HSTDV)的研制,该飞行器将以固体助推火箭和超燃冲压发动机为动力,初步设想是使超燃冲压发动机启动并推动飞行器以高超声速飞行20秒,最终目标是研制能够在32.5千米高空以马赫数6与的速度飞行的高超声速飞行器。同时,这一项目也暗示印度可能发展可重复使用航天运载器。建造中的 HSTDV 演示飞行器重1吨,长5.6米,其横截面为八边形,机     

激波对超声速流中横向射流的影响

为了揭示激波对超声速流中横向射流的影响,在超声速流中利用长9mm、坡度为23°的斜坡产生激波。组合利用高速摄影仪和纹影仪拍摄激波入射在气体和液体射流的不同位置,以及相同位置不同喷注压降时的流场纹影和阴影图像。结果表明,激波对气体和液体横向射流的影响基本相同,都表现为入射激波增强了湍流度,扩大了燃料空间发展区域,增强了与主流的混合,激波入射在射流的前部比射流的后部影响大。     

气氧甲烷溅板式层板喷注器燃烧特性试验分析

采用试验方法分别对单喷嘴和多喷嘴溅板式层板喷注器燃烧特性进行研究,考察不同工况下喷注器面板热载情况,得到不同混合比、不同结构参数对燃烧室压力分布和燃烧效率的影响规律。试验结果表明:混合比对多喷嘴喷注器燃烧室压力影响不大,但对燃烧效率有较大影响。对于单喷嘴喷注器,燃烧效率随着混合比的增加而增高。相同条件下,增大扩张角及出口层宽度有利于提高喷注器燃烧效率,但会引起喷注面板热载增大,各喷注器喷注面板均产生不同程度的变形或失效。该结果对于正确指导层板式喷注器的设计以及筛选喷注器结构具有重要意义。     

S弯进气道合成双射流流场控制特性分析

针对飞翼布局无人飞行器中S弯进气道明显流动分离和出口总压畸变等问题,提出了基于合成双射流的主动流动控制方法,建立了合成双射流的S弯进气道数值仿真模型。结果表明,在S弯进气道分离点附近施加合成双射流控制,在整个射流周期内通过“吹”“吸”接力可以有效抑制边界层流动分离,有效提升总压恢复系数。对比研究了合成双射流不同射流角度、射流峰值速度和激励频率对S弯进气道流场控制特性的影响规律。结果表明合成双射流与主流的角度越小,流动分离控制效果越好,较大射流峰值速度会对主流形成“阻挡”致使控制效果下降,激励频率与流场特征频率越接近控制效果越明显。     

横向运动板干扰聚能射流的数值模拟

基于有限元分析软件ANSYS/LS-DYNA和LS-PREPOST,用ALE算法对射流垂直侵彻横向运动防护板的过程进行模拟分析。防护板在不同速度下干扰射流时,对防护板和后效板上的开坑形状进行分析,并计算后效板上的最终侵深及射流轴线上的速度降,得到射流在横向防护板作用下后效板侵深及射流轴线上的速度降随防护板速度变化的曲线。结果表明,防护板抗射流侵彻能力随防护板速度的增加而增强,尤其是防护板横向速度在0～100m/s增加时,抗射流侵彻能力增强较为明显。     

Reaction characteristic of PTFE/Al/Cu/Pb composites and application in shaped charge liner

In this paper, the reaction characteristic and its application in shaped charge warhead of a novel reactive material, which introduced copper (Cu) and plumbum (Pb) into traditional polytetrafluoroethylene/aluminum (PTFE/Al), are studied. The thermal analysis and chemical reaction behavior of the PTFE/Al/Cu/Pb mixture are investigated by Differential Scanning Calorimetry (DSC),Thermo-gravimetry (TG), and X-ray Diffraction (XRD) techniques. Then, the shaped charge liners with PTFE/Al/Cu/Pb reactive materials are fabricated, and the X-ray experiments show that they could form reactive jets with excellent performance under the detonation effects of the shaped charge. Based on that, the penetration experiments of shaped charge with PTFE/Al/Cu/Pb reactive liner against steel plates are carried out, and the results demonstrate that the PTFE/Al/Cu/Pb reactive jets could produce a deeper penetration depth compared to the traditional PTFE/Al reactive jets. Meanwhile, the PTFE/Al/Cu/Pb reactive jets also show significant inner-blast effects, leading to dramatically cracking or fragmentation behavior of the penetrated steel plates. This new PTFE/Al/Cu/Pb reactive liner shaped charge presents enhanced penetration behavior for steel targets that incorporates the penetration capability of a high-density and ductility jet, and the chemical energy release of PTFE-matrix reactive materials.     

Theoretical and numerical simulation study on jet formation and penetration of different liner structures driven by electromagnetic pressure

The use of a shaped liner driven by electromagnetic force is a new means of forming jets. To study the mechanism of jet formation driven by electromagnetic force, we considered the current skin effect and the characteristics of electromagnetic loading and established a coupling model of"Electric—Magnetic—Force"and the theoretical model of jet formation under electromagnetic force. The jet formation and penetration of conical and trumpet liners have been calculated. Then, a numerical simulation of liner collapse under electromagnetic force, jet generation, and the stretching motion were performed using an ANSYS multiphysics processor. The calculated jet velocity, jet shape, and depth of penetration were consistent with the experimental results, with a relative error of less than 10％. In addition, we calculated the jet formation of different curvature trumpet liners driven by the same loading condition and ob-tained the influence rule of the curvature of the liner on jet formation. Results show that the theoretical model and the ANSYS multiphysics numerical method can effectively calculate the jet formation of liners driven by electromagnetic force, and in a certain range, the greater the curvature of the liner is, the greater the jet velocity is.     

直接力/气动力复合控制系统的有限时间镇定

考虑到复合控制系统中,直接力的离散特性会使系统的设计复杂化。针对采用姿控式直/气复合控制的导弹,基于有限时间稳定理论,引入辅助滑模面,研究其控制系统的有限时间镇定,得到一个受控良好的复合控制系统。在此基础上,利用辅助模糊控制,对系统不确定性进行估计,进一步改善了复合系统的控制品质。最后以俯仰通道为例,对所提出的方法进行仿真,结果验证了该方法的有效性。     

Experimental and numerical investigation of zirconium jet performance with different liner shapes design

This paper studies the shaped charge jet performance in terms of different liner shapes including conical,bell,hemispherical and bi-conical liners.The critical angles and the relevant flow velocities for the zir-conium liner material were calculated analytically and numerically using Autodyn hydro-code.The relationship between the critical collapse angle and the flow velocity was determined for the conditions of jet formation and coherency.Penetration tests according to the standard testing procedures of API-RP34 (Section-Ⅱ) were performed to validate the numerical predictions of the jet performance of the studied liners.It was found that the four shaped charge liners all produced coherent jets with different performances.The penetration depth of the shaped charges with the bell and the bi-conical liner shapes increased by 10.3％ and 22％,respectively,while the crater diameter of shaped charge with hemispherical liner increased by 85％ representing the formation of an explosively-formed-projectile (EFP),when they are compared with the corresponding jet characteristics of a conical liner shaped charge.     

Investigate the effects of magnetic fields on the penetration ability of a shaped charge jet at different standoffs

The influence of a magnetic field on the stability of a shaped charge jet is experimentally investigated at standoffs of 490, 650 and 800 mm. The experimental results without and with the magnetic field are compared in terms of the shaped charge jet form, stability and penetration ability. A theoretical model based on one-dimension fluid dynamics is then developed to assess the depth of penetration of the shaped charge at those three standoffs and magnetic conditions. The results show that the penetration capability can be enhanced in more than 70% by the magnetic field. The theoretical calculations are compared with the experimental results with reasonably good correlation. In addition, the parameters introduced in the theory are discussed together with the experiments at three standoffs studied.     

合成双射流冲击平板流场结构与模态分解分析

为揭示合成双射流冲击平板流场结构特征,通过大涡模拟方法对合成双射流冲击平板流动进行了仿真,采用有限时间Lyapunov指数方法对流场的拉格朗日涡结构进行了识别,并与欧拉框架下的速度矢量和涡量结果进行了对比分析。结果表明,在合成双射流两股射流交替作用下,射流核心区涡系结构较为复杂且涡量丰富,远离核心区存在一对稳定的涡结构,且拉格朗日涡结构与涡量对应较好,为合成双射流冲击冷却的布局设计提供了指导。另外,流场本征正交分解表明,第一阶模态关于激励器出口中心轴线大致对称,其能量占总体能量的35%,前6阶模态的能量占80%;根据前6阶模态所反映的流场特性,合成双射流冲击平板流场具有高度的对称性。     

Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

Investigation on the influence of the initial RDX crystal size on the performance of shaped charge warheads

Copper lined wave shaped shaped charges of particular design and liner metallurgy were used to investigate the effect of explosive crystal size on the resultant shaped charge jet parameters. Composition A3 with RDX of three different average crystal sizes, i.e. 30 μm, 100 μm and 300 μm were used in the investigation. All other parameters in the charge were kept constant and in particular, care was given to obtain consistent dimensional quality and liner microstructure, in order to prohibit the variation of other parameters. Specific flash-X-ray diagnostics were used in field tests to obtain the jet parameters from multiple firings of similar charges. It is found that the varying crystal size of the RDX has a marginal influence in the total jet length of the jets. However, it is also found that there is less variation between firings in the jet parameters for jets from the charges loaded with the crystal size of 100 μm.