Influences of different crossing types on dynamic response of underground cavern subjected to ground shock

An intersecting cavern is a common structural form used in underground engineering, and its safety and stability performance directly control the service performance of the whole project. The dynamic re-sponses of the three kinds of crossing type (+-shaped, T-shaped, L-shaped) caverns subjected to ground shock were studied by numerical simulation. The velocity plus force mode boundary setting method was proposed in the coupled static and dynamic analysis of a deep underground cavern. The results show that, among the three types of crossing caverns, the+-shaped cavern is the most significantly affected by the dynamic action, followed by T-shaped, and then L-shaped caverns. The vault settlement, straight wall deformation, vault peak particle velocity, effective plastic strain of surrounding rock, and maximum principal stress and strain at the bottom of the lining of the straight wall increase with the increase of cavern span. The vault settlement, straight wall deformation, effective plastic strain of surrounding rock, and the maximum principal stress and strain at the bottom of lining to the straight wall decrease with the increase of lateral pressure coefficient, and the peak particle velocity at the vault increases. The variation is small compared with the change of cavern span. The influence range of the underground cavern intersection is two cavern diameters from the intersection centre. The bottom of the straight wall at the intersection is the weak part. It is suggested to thicken the support locally to improve the stability of the cavern.     

Effect of friction stir processing on mechanical properties and heat transfer of TIG welded joint of AA6061 and AA7075

Tungsten inert gas (TIG) welding is the most commonly used joining process for aluminum alloy for AA6061 and AA7075 which are highly demanded in the aerospace engineering and the automobile sector, but there are some defects occur during TIG welding like micro-crack, coarse grain structure, and porosity. To improve these defects, the TIG welded joint is processed using friction stir processing (FSP). This paper presents the effect of friction stir processing on TIG welding with filler ER4043 and ER 5356 for dissimilar aluminum alloy AA6061 and AA7075. The mechanical characterization, finite element formulation and mathematical equations of heat transfer of TIG + FSP welded joints are investigated using ANSYS Fluent software by adjusting process parameters of FSP. The results show that the maximum compressive residual stress 73 MPa was obtained at the fusion zone (FZ) of the TIG weldment with filler ER4043, whereas minimum compressive residual stress 37 MPa was obtained at stir zone (SZ) of the TIG+FSP with filler 5356. The maximum heat flux 5.33 × 106 W/m2 and temperature 515 ℃ have observed at tool rotation 1600 rpm with a feed rate of 63 mm/min. These results give a satisfactory measure of confidence in the fidelity of the simulation     

自润滑弹带挤进过程中渗出油量的对比计算

从弹带的作用及特性出发, 通过数值计算和统计计算 2种方法计算了自润滑弹带挤进过程中的渗出油量,初步得出了渗出油量和行程之间的关系。这一问题的解决为自润滑弹带材料的选择提供了理论依据。通过对 2种算法的比较可知, 数值计算误差更小一些, 而统计计算对数学条件要求不太苛刻。     

Burgers’方程的守恒律

守恒律历来是物理学研究的中心课题之一.在数学中借助运动常数,对偏微分方程的解作出先验估计,这些估计是方程的解存在性、唯一性及稳定性的核心关键.在计算数学中较好的稳定差分格式,也用到守恒律.在Noether's定理求守恒律的基础上,利用Burgers'方程的对称群构造出相关的伴随因子得出了Burgers'方程的一类守恒律.     

两栖装备乘员可靠性影响因素分析

人的可靠性指的是人在规定的时间内、规定的条件下、完成规定任务的能力,它是整个系统可靠性一个重要的组成部分,作为装甲装备而言,乘员可靠性的高低直接影响到整个装备作战系统可靠性.针对两栖装备的使用环境和使用特点,对影响乘员可靠性的因素进行了分析,得出了结论,对于如何提高两栖装备乘员可靠性有一定的指导意义.     

大功率消磁线圈受力分析与计算

大功率消磁线圈在运行中会受到较强电磁力的作用,客观地分析和计算电磁力的大小及分布情况,是设计和建造大型消磁站的一项基础性的工作.文中从电磁场基本原理出发,应用张量理论分析、计算了大功率消磁线圈的受力情况,对于设计和建造大型消磁站具有参考作用.     

基于专家系统的防化保障预案评估研究

人工智能技术在众多领域获得广泛应用．为满足现代战争对防化指挥手段的现代化要求,针对不易量化的防化指挥决策问题的评估,提出了构建知识库并应用模糊推理机制建立专家系统,据此进行防化保障预案的评估选优方法,并对该方法的求解过程进行了探讨．     

一种改进的强跟踪滤波算法的推导及仿真验证

针对一般强跟踪滤波算法(STEKF)在光纤陀螺动态输出滤波过程中存在跟踪效果不好的缺陷,分析推导一种新的强跟踪滤波算法(ISTEKF),使其能够克服原先算法存在的缺陷,并利用光纤陀螺动态输出数据进行仿真验证,滤波结果表明ISTEKF算法能够达到很好的跟踪效果,且具有较强的自适应能力。     

某型飞机平尾轴疲劳断裂失效分析

采用台架试验装置对某型飞机平尾轴进行了疲劳试验,通过断口的观察分析、断口部位的金相分析、硬度检测、有限元结构应力分析,确定了平尾轴的失效模式,并对其断裂失效原因进行了分析。结果表明：平尾轴的断裂性质为疲劳断裂,裂纹源均起源于大轴简体内壁加工刀痕形成的沟槽处,变截面圆弧造成的结构应力集中和粗糙加工刀痕形成的附加应力集中是造成大轴疲劳断裂的主要原因。关键词：平尾轴;疲劳断裂;失效分析;应力集中     

全反射棱镜式激光陀螺应力检测技术研究

光学元件的装配应力和加工应力是制约高精度激光陀螺稳定工作的重要因素．考虑各向同性材料在应力作用下介电常量变化的情况,利用弹光效应和琼斯矩阵得到了复杂应力与穿过全反射棱镜的激光束偏振态改变之间的关系．通过实验,提出一种通过记录棱镜布儒斯特角反射光椭偏度配合光斑质量分析应力水平的筛选方法,对棱镜式激光陀螺装配过程中光学元件应力的早期筛查有突出作用,并设计专用工装以适应棱镜相关产品的应力检测需要．