Y-La-Si3N4陶瓷的高温力学性能及氧化特征

研究了Y_2O_3和La_2O_3添加剂Si_3N_4陶瓷的高温力学性能和氧化行为。实验结果表明,其抗弯强度值可保持到1350℃,断裂韧性则随温度的升高而增加,到1350℃出现“峰”值;在120O～I350℃范围内,15mol％添加剂Si_3N_4的氧化符合抛物线规律,氧化过程主要由晶界添加剂离子和少量杂质离子的扩散控制。表面氧化产生的化合物导致表面裂纹使抗弯强度大大降低。     

均匀设计在柴油无灰节能降污添加剂配方研制中的应用

基于低压氧弹燃烧法研究了充氧压力分别为0．6MPa和0．9MPa时两种无灰型柴油添加剂不同配比对助燃性能的影响。采用均匀实验设计和Matlab回归优化的方法，得到复配体系的最优配方，并对其进行了验证。结果表明，由Matlab回归分析得到的完全二次回归模型最理想，0．6MPa时由该模型得到的最优配方为：添加剂A和B的质量分数分别是0．300‰和0．700‰，并通过实验验证得到的发热量达到最大，变化率为8．697％。0．9MPa时，结合直观分析和回归分析，得到与实际相符的最优配方：添加剂A和B的质量分数分别是0．600‰和0．900‰，此时发热量皮化率为4．453％。     

超细矿物微粉改善2号坦克润滑脂摩擦学性能研究

采用球盘式摩擦磨损试验机，研究了羟基硅酸盐超细矿物微粉作为2号坦克润滑脂添加剂对钢／钢摩擦副的润滑性能，利用扫描电子显微镜（Scanning Electron Microscopy，SEM）和X射线能谱仪（Energy Dispersive Spectrometry，EDS）分析了磨痕表面形貌及典型元素的面分布情况。结果表明：超细矿物微粉可显著改善2号坦克润滑脂的抗磨减摩性能，含2wt％矿物微粉的润滑脂同单一2号润滑脂相比，摩擦系数降低了约44％，钢盘磨损率降低了约70％，这与羟基硅酸盐可在摩擦表面形成一层富含O，Si，Mg，Al等元素的摩擦表面膜密切相关。     

一种有机膨润土润滑脂的性能研究

以有机膨润土、HVI400矿物基础油、添加剂和极性助分散剂为原料,实验研究一种有机膨润土润滑脂,较详细地考察了极性助分散剂、添加剂及制备工艺（搅拌速度、搅拌时间、研磨次数）对膨润土润滑脂性能的影响.实验结果表明极性助分散剂采用丙酮时制备的膨润土润滑脂性能良好;液态添加剂比固体添加剂的效果好;制备工艺对膨润土润滑脂的性能有一定影响.采用15%有机膨润土稠化剂和85%HVI400矿物基础油,以2%-4%丙酮作极性助分散剂,添加0.5%抗氧剂、0.5%防锈剂、1%油性剂和4%极压抗磨剂,制备工艺为快速搅拌30 min,研制出一种性能良好的极压膨润土润滑脂,该润滑脂具有良好的高温性、胶体安定性、机械安定性、防锈性、抗水性和极压抗磨性.     

环烷酸铅作为润滑油添加剂的摩擦学性能研究

环烷酸铅具有良好的抗磨损能力和减摩性能，其中含铅量为２０％的环烷酸铅添加剂使基础油的抗磨性能提高４０％，减摩性能提高３０％。ＳＥＭ分析显示钢球磨痕和犁沟较浅，且有含铅沉积物生成。由此推断出有机铅盐在摩擦副表面形成吸附膜，且部分吸附膜发生摩擦化学反应，产生了其有抗磨减摩作用的铅氧化物转化膜，从而起到了改善摩擦磨损性能的作用。     

日本开发水库淤泥饲料添加剂

最近,日本高远町松木微生物研究所科技人员,开发利用水库底淤泥制成饲料添加剂,这种添加剂比用人工配合制成的饲料营养添加剂,可降低成本85—90％以上。     

SiO_2在SHS铝热-重力分离法制备陶瓷内衬复合钢管中的作用

采用自蔓延铝热-重力分离法,制备了陶瓷内衬复合钢管,并系统研究了SiO_2添加剂对SHS燃烧过程、陶瓷层相对密度与组织结构、复合钢管力学性能的影响。经研究发现,SiO_2在铝热燃烧过程中作为稀释剂存在,随着SiO_2添加量增多,燃烧温度与蔓延速率下降,并使分布于α-Al_2O_3枝晶晶界处的亚稳定相FeO·Al_2O_3增多;陶瓷相对密度与复合钢管抗压溃强度在SiO_2含量为2wt％时出现极大值(分别为92.5％与430MPa);陶瓷硬度、断裂韧性与复合钢管抗压剪强度随SiO_2含量增加而降低。     

怎样从外包装鉴别饲料添加剂

目前，市场上的饲料添加剂种类繁多，鱼目混珠，而广大养殖户都是从外包装上来确定购买何种饲料添加剂：一看是否有产品质量检验合格证和产品质量标准。二看是否有产品批准文号和生产许可证号。批准文号的有效期为5年，超过期限的，不要购买。     

Cu/C复合型润滑添加剂减摩抗磨性能研究

将纳米Cu和纳米金刚石复配成Cu/C复合添加剂,对其在500SN基础油中的减摩抗磨性能进行了研究.结果表明,加入了Cu/C复合添加剂的试油能明显改善500SN基础油的摩擦学性能:当纳米Cu添加量为4%,纳米C添加量为2%时,加入了Cu/C复合添加剂的试油减摩性能最好,同500SN空白试油相比,摩擦因数可降低94.8%;...     

抗磨添加剂与电弧喷涂耐磨涂层间的协同效应

研究了2种φ2mm粉芯丝材电弧喷涂Fe-Cr-Ni涂层和7Crl3涂层以及与2种典型润滑油抗磨添加剂的协同效应,并借助X光电子能谱(XPS)研究了其协同作用机理.结果表明DBP和ZDDP润滑油抗磨添加剂能明显地改善电弧喷涂Fe-Cr-Ni涂层和7Cr13涂层的抗磨性.添加剂DBP能显著地降低2种电弧喷涂涂层/GCr15摩擦副的摩擦系数,但ZDDP抗磨添加u剂的减摩效果不太显著.在含DBP和ZDDP添加剂油润滑条件下,涂层磨痕表面形成了摩擦化学反应膜.     

Storage life prediction under pre-strained thermally-accelerated aging of HTPB coating using the change of crosslinking density

In order to predict the storage life of a certain type of HTPB (hydroyl-terminated polybutadiene) coating at 25 C and analyze the influence of pre-strain on the storage life, the accelerated aging tests of HTPB coating at 40 C, 50 C, 60 C, 70 C with the pre-strain of 0%, 3%, 6%, 9%, respectively were carried out. The variation regularity of the change of crosslinking density was analyzed and the aging model of HTPB coating under pre-strained thermally-accelerated aging was proposed. The storage life of HTPB coating at 25 C was estimated by using the Berthelot equation as the end point of the aging life with a 30% decrease in maximum elongation. The results showed that the change of crosslinking density of HTPB coating increased with the increase of aging temperature and aging time, and decreased with the in-crease of pre-strain. Under 0% pre-strain, the relationship between the change of crosslinking density of HTPB coating and the aging time can be described by the logarithmic model with the confidence probability greater than 99%.The stress relaxation phenomenon existed under 3%, 6% and 9% pre-strained aging. The aging model considering chemical aging and pre-strain was established with the confidence probability greater than 90%. The storage life of HTPB coating was 15.2935 years at 25 C under 0% pre-strain, which was reduced by 13.9007%, 75.6949% and 89.7859% under 3%, 6% and 9% pre-strain, respectively. The existence of pre-strain has a serious impact on the storage life of HTPB coating, therefore, the pre-strain should be avoided as much as possible during the actual storage.     

植物对PAHs污染土壤修复效果的种间差异研究

采用盆栽试验法,研究了黑麦草、苏丹草、油菜对土壤中菲、芘的去除效果,及植物和微生物去除土壤中菲、芘的交互效应。结果显示：菲、芘质量比约为80 mg.kg-1时,土壤-植物系统对菲、芘的去除效果明显。种植黑麦草、苏丹草、油菜60 d后,土壤菲、芘降解率分别为62.70%,76.25%,26.48%和47.80%,65.26%,23.56%,分别比无植物对照高39.69%,53.24%,3.47%和30.06%,47.48%,5.78%。本实验说明,植物可以促进微生物对土壤中菲、芘的降解,其中根系发达的苏丹草对微生物降解的促进作用最为显著。     

生物柴油降低装甲车辆柴油机排放的试验研究

在柴油中添加20%的生物柴油,通过试验研究了掺混后的燃料对装甲车辆柴油机动力输出和排放的影响。结果表明：添加20%的生物柴油对各转速下最大输出扭矩影响不大,最大降幅小于2%;常用转速下（1400r/min）全负荷范围内降低碳烟的效果较好,可降低23%～100%;同时,HC排放量可降低11%～70%,CO排放量可降低33%;外特性工况下,在中、高转速时亦可降低碳烟排放22%～46%,但NOx排放有一定程度升高,部分工况下升高10%左右。     

Multifunctional A356 alloy/ PKSAnp composites: Microstructure and mechanical properties

Mechanical properties and microstructure of multifunctional composites produced with palm kernel shell ash nanoparticle (PKSAnp)-A356 alloy composites was studied. The composites were produced using Double layer feeding stir casting method (DLF-SCM) by adding 1 wt%‒4 wt.% PKSAnp. The microstructure, density, electrical and mechanical properties were determined. The results shows that there was a uniform distribution of the PKSAnp in A356 alloy. The mismatch at the interface between the PKSAnp and A356 alloy was 4.26%. Improvement of 30.47%, 41.91%, 49.52%, 40.90% and 65.09% were obtained for hardness values, tensile, yield strength, %elongation and impact energy at 4 wt% PKASnp. The work has established that the developed composites can be used for multifunctional applications where combination of toughness and strength is vital.     

碳化钨及其混合物的冲击 Hugoniot数据计算

计算了多孔碳化钨（初始密度分别为密实碳化钨密度的９５％、８５％、７５％和６５％）在不完全压实状态和完全压实状态下的Ｐ_１－Ｖ_１曲线和Ｃｓ－Ｕ１曲线以及碳化钨／碳、碳化钨／碳化硅混合物（碳化钨含量分别为３％,５％,１０％）的Ｐ_１－Ｖ_１曲线和Ｃ_ｓ－Ｕ_１曲线。     

面向像斑的高分辨率遥感影像自优化迭代分类方法

针对高分辨率遥感影像提出了一种面向像斑的自优化迭代分类算法,基于半监督聚类算法获取训练样本,以支持向量机为核心设计了自优化迭代分类器。使用分型网络演化算法获取像斑,并从中选取少量标记样本;结合标记样本,利用半监督模糊C均值算法对像斑进行聚类,并基于密集度筛选得到训练样本;设计了自优化迭代支持向量机分类算法,对所有像斑进行迭代分类直到满足分类要求,并在分类过程中对近邻分类结果进行统计得到高可信度样本以自主优化训练样本集。基于以上方法分别对武汉市QuickBird和WorldView影像进行分类实验,分类总精度分别达到94.67%与92%,与基于人工选取训练样本情况下进行分类的分类总精度（82%与82.67%）、常规支持向量机分类总精度（87.33%与88%）、最小二乘支持向量机分类总精度（88%与89.33%）相比,精度有明显提升,分类效果较好。     

Study of nano-nitramine explosives: preparation,sensitivity and application

Nano-nitramine explosives (RDX, HMX, CL-20) are produced on a bi-directional grinding mill. The scanning electron microscope (SEM) observations show that the prepared particles are semi-spherical, and the narrow size distributions are characterized using the laser particle size analyzer. Compared with the micron-sized samples, the nano-products show obvious decrease in friction and impact sensitivities. In the case of shock sensitivities, nano-products have lower values by 59.9% (RDX), 56.4% (HMX), and 58.1% (CL-20), respectively. When nano-RDX and nano-HMX are used in plastic bonded explosives (PBX) as alternative materials of micron-sized particles, their shock sensitivities are significantly decreased by 24.5% (RDX) and 22.9% (HMX), and their detonation velocities are increased by about 1.7%. Therefore, it is expected to promote the application of nano-nitramine explosives in PBXs and composite modified double-based propellants (CMDBs) so that some of their properties would be improved.     

Experimental investigations on wear properties of Palm kernel reinforced composites for brake pad applications

The use of asbestos material is being avoided to manufacture the brake pads as it is harmful and toxic in nature. Further it leads to various health issues like asbestosis, mesothelioma and lung cancers. These brake pads can be replaced by natural fibers like Palm kernel (0–50%), Nile roses (0–15%) and Wheat (0–10%) with additives like aluminum oxide (5%–20%) and graphite powder (10%–35%). Phenolic resin of 35% is utilized as a binder. Particulated Nile roses are used to increase the friction coefficient and wheat powder is used to reduce the wear rate. Aluminum oxide and graphite are abrasive in nature. This helps to make brake pads with high friction co-efficient and less wear rate with low noise pollution. The wear of the proposed composites have been investigated at different speeds. Various tests like wear on pin-on-disc apparatus, hardness on the Rockwell hardness apparatus and oil absorption test have been conducted. Phenolic resin produces good bonding nature to fiber. Thus, Fibers found to have performed palatably among all commercial brake pads. The objective of the research indicates that Palm kernal shell could be a conceivable alternative for asbestos in friction coating materials.     

重庆市某混合式热泵工程经济配置方案模拟分析

基于重庆市某混合式热泵工程,采用TRNSYS软件分别就室内温度、湖水温度、地埋管流体温度以及供冷能耗进行了模拟,并与实际运行数据进行对比分析,确定了该模型的准确性和可行性.最后对土壤源热泵承担总负荷15％,25％,35％,45％的4种方案与传统方案一同进行模拟分析,结果显示,土壤源热泵25％的负荷比例在4种配置方案中最...