反对称铺层碳纤维复合材料圆柱壳的双稳态应力特性

双稳态复合材料可广泛应用于各类可变结构的设计。针对反对称铺层的圆柱壳,利用有限元软件ABAQUS的Standard准静态分析,模拟其双稳态跳变过程和跳回过程,探讨在整个连续过程中圆柱壳上的应力分布情况,以及应力随时间和载荷变化的趋势,从而对该类可变结构的设计起到指导作用。结果表明:该类复合材料圆柱壳跳变过程中最大应力出现在载荷施加点与约束点附近,第二稳态下应力关于板中心呈中心对称分布,最大应力沿板壳对角线出现在四个角内侧附近,而跳回过程中应力由第二稳态下的分布慢慢变为集中在约束点附近。而且整个圆柱壳上的最大应力时刻与最大载荷施加的时刻不重叠,具有滞后性。     

光学波导中原子干涉的加速度测量

提出一种水平方向、光学波导中原子干涉的加速度测量方案。详细介绍了光路结构、原子团制备以及光学波导的绝热装载等。通过实验手段对测量方案进行验证,首先将~(87)Rb原子团冷却至50 nK的玻色爱因斯坦凝聚态,随后对超冷原子团施加布拉格光进行分束、合束,完成原子干涉过程。实验结果显示,所提干涉测量系统能够实现单轴加速度测量,对未来高精度多轴加速度测量系统的研制具有指导借鉴意义。     

Experimental investigation for machinability aspects of graphene oxide/carbon fiber reinforced polymer nanocomposites and predictive modeling using hybrid approach

This article explores the drilling behavior of polymer nanocomposites reinforced by Graphene oxide/Carbon fiber using a hybrid method of Grey theory and Principal component analysis (GR-PCA). An online digital dynamometer was employed for the evaluation of Thrust Force and Torque. The image processing technique computes the delamination. Response surface methodology (RSM) considers the parameters, namely, drilling speed (S), feed rate (F), Graphene Oxide wt.% (G) in designing the experimentation array. Principal component analysis (PCA) was used to tackle the response priority weight during the combination of multiple functions. Analysis of variance (ANOVA) scrutinized the influence of parameters and intended the regression models to predict the response. GR-PCA evaluated the optimal parametric setting and remarked that feed rate acts as the most predominant factor. The higher feed rate and wt.% of G is responsible for surface damages like fiber pull-out, fiber fracture and cracks. A significant improvement in drilling responses has been obtained and also validates through confirmatory test and microstructure investigations.     

基于自准直反射法的光学中心偏检测系统研究

提出了一种基于自准直反射法测量光学中心偏的检测方法,分析了其测量光学中心偏的基本原理,在此基础上设计了基于自准直反射法的光学镜组中心偏检测系统。系统采用CV-A1型CCD探测器组件,以轴向晃动≤1″、径向跳动≤1μm的高精度基准轴工作台配合PIV研华工控机进行数据采集和图像处理,系统测量精度为:角度≤2,″线度≤0.01 mm。实际应用表明,该系统适用于1.06μm激光探测系统光学镜组的在线装校及系统中心偏检测,也可用于其它光学系统中心偏的测量。     

基于PON技术的多站雷达数字光纤传输系统设计

提出一种多站雷达体系雷达数据光纤传输系统的方案设计和实现方法。与传统雷达使用的光纤传输系统不同,而是采用技术较新的基于无源光网络PON的实时数据通信系统,这是无源光网络技术在多传感器实时通信领域的首次应用。在系统设计中利用先进的光电子和在编程技术,实现了点对多点雷达数据光纤传输,提高了信号传输质量,同时系统具有动态接入和扩容的能力。     

L波段掺铒光纤放大器增益钳制及提高特性研究

报道了一种新型980 nm激光二极管(LD)泵浦高增益的掺铒光纤放大器(EDFA).通过加入中心波长为1 550 nm光纤光栅(FBG)可以明显提高增益,并分析了增益钳制的原理.实验得到其增益比无FBG结构EDFA提高8 dB,并得到了小信号输入时增益25 dB的有效钳制.     

基于复杂排队系统的TOC服务模型与性能分析

三值光学计算机的运算请求处理过程缺乏合理、系统的性能评价标准与体系。基于M/M/1、M/M/n、MX/M/1和M/MB/1构成的复杂排队系统,构建了三值光学计算机的四阶段服务模型,同时建立了立即调度和结束时调度两种不同策略与算法。基于不同排队系统讨论了运算请求的接收时间、预处理时间、运算时间和发送时间的计算方法,进而得到最终响应时间。最后,通过仿真实验对两种策略的模型进行验证,结果表明结束时调度策略明显优于立即调度策略。     

Investigation of the mechanical and ballistic properties of hybrid carbon/ aramid woven laminates

High-performance ballistic fibers, such as aramid fiber and ultra-high-molecular-weight polyethylene (UHMWPE), are commonly used in anti-ballistic structures due to their low density, high tensile strength and high specific modulus. However, their low modulus in the thickness direction and insufficient shear strength limits their application in certain ballistic structure. In contrast, carbon fiber reinforced epoxy resin matrix composites (CFRP) have the characteristics of high modulus in the thickness direction and high shear resistance. However, carbon fibers are rarely used and applied for protection purposes. A hybridization with aramid fiber reinforced epoxy resin matrix composites (AFRP) and CFRP has the potential to improve the stiffness and the ballistic property of the typical ballistic fiber composites. The hybrid effects on the flexural property and ballistic performance of the hybrid CFRP/AFRP laminates were investigated. Through conducting mechanical property tests and ballistic tests, two sets of reliable simulation parameters for AFRP and CFRP were established using LS-DYNA software, respectively. The experimental results suggested that by increasing the content of CFRP that the flexural properties of hybrid CFRP/AFRP laminates were enhanced. The ballistic tests’ results and the simulation illustrated that the specific energy absorption by the perforation method of CFRP achieved 77.7% of AFRP. When CFRP was on the striking face, the shear resistance of the laminates and the resistance force to the projectiles was promoted at the initial penetration stage. The proportion of fiber tensile failures in the AFRP layers was also enhanced with the addition of CFRP during the penetration process. These improvements resulted in the ballistic performance of hybrid CFRP/AFRP laminates was better than AFRP when the CFRP content was 20 wt% and 30 wt%.     

新型夜瞄复合荧光材料在步兵轻武器中的应用研究

采用自制的复合荧光粉体和化学载体成分,研制出一种步兵轻武器新型夜瞄复合荧光材料.试验研究和实际使用结果表明,研制的新材料发光时间长、亮度高,具有良好的耐温、耐腐蚀性能,不受轻武器的日常使用和维护影响,可满足步兵轻武器夜间瞄准需求.     

Performance evaluation and optimization design of photoelectric pyrometer detection optical system

The measurement and control of high temperature play very important roles in national defense, military, scientific experiments, industrial and agricultural production. Photoelectric pyrometer is one of the important radiation thermometers for non-contact temperature measurement. It has an important application in the field of high temperature measurement, and its performance directly affects the accuracy of temperature measurement. By improving the design of the detection optical system of the photoelectric pyrometer, the imaging performance of the photoelectric pyrometer can be improved effectively, and the temperature measurement accuracy can be improved. In this paper, the temperature measurement principle of photoelectric pyrometer, the working principle of the detection optical system and the composition of the system are introduced. The optical components that affect the imaging of the optical system of the photoelectric pyrometer are analyzed. The optical pyrometer detection optical system is simulated by ZEMAX software, based on the analysis results, the Modulation Transfer Function (MTF) and the spot Diagram are used as the main evaluation criteria to optimize the design of the objective lens of the photoelectric pyrometer detection optical system. The imaging performance of the photoelectric pyrometer detection optical system and the accuracy of temperature measurement of the photoelectric pyrometer are improved by optimization design of the detection optical system.