多轴向织物层合板层间剪切强度有限元分析与实验研究

用VIMP工艺制备了UD、0/45/-45、0/45/90/-45三种多轴向织物增强,四种厚度的GFRP层合板试样,采用短梁剪切实验考察了层间剪切强度和破坏模式。建立了GFRP层合板短梁剪切试样有限元模型,计算了内部层间剪应力分布。结合计算和实验结果分析表明层合板存在由宽度方向层间剪应力变化导致的自由边缘效应,含偏轴铺层的层合板更容易发生边缘开裂破坏。厚度相同时0/45/-45多轴向织物增强层合板的层间剪切强度最高。短梁剪切强度测试存在尺寸效应,随着厚度的增加,强度下降,样品波动系数增大。     

复合材料结构传热分析的新的高阶热层合理论研究

提出了新的高阶热层合理论及相应的有限元模型．新的高阶热层合理论比作者最初提出的一阶热层合理论［１］前进了一大步,它有效克服了一阶热层合理论中存在的计算缺陷．大量数值算例表明了高阶热层合理论的精确有效性．算例还对铺设角和纵厚比对层合板温度场的影响进行了分析,并得到了一些有意义的结论．     

型钢混凝土桁架转换层的监控与分析

对贵阳市某大楼型钢混凝土桁架转换层进行了施工期间的监控,并利用有限元分析软件ANSYS建立了带有型钢混凝土桁架转换层的结构有限元分析模型.针对工程中连接、构造和施工影响等相关因素进行有限元模型的对比分析,明确各因素对桁架受力的影响.结合施工阶段的监控数据,分析此工程中桁架受力状态的成因,为准确判断工程在正常投入使用后的...     

Damage visualization and deformation measurement in glass laminates during projectile penetration

Transparent armor consists of glass-polymer laminates in most cases. The formation and propagation of damage in the different glass layers has a strong influence on the ballistic resistance of such laminates. In order to clarify the course of events during projectile penetration, an experimental technique was developed, which allows visualizing the onset and propagation of damage in each single layer of the laminate. A telecentric objective lens was used together with a microsecond video camera that allows recording 100 frames at a maximum rate of 1 MHz in a backlit photography set-up. With this technique, the damage evolution could be visualized in glass laminates consisting of four glass layers with lateral dimensions 500 mm × 500 mm. Damage evolution was recorded during penetration of 7.62 mm AP projectiles with tungsten carbide core and a total mass of 11.1 g in the impact velocity range from 800 to 880 m/s. In order to measure the deformation of single glass plates within the laminates, a piece of reflecting tape was attached to the corresponding glass plate, and photonic Doppler velocimetry (PDV) was applied. With the photonic Doppler velocimeter, an infrared laser is used to illuminate an object to be measured and the Doppler-shifted light is superimposed to a reference light beam at the detector. The simultaneous visualization and PDV measurement of the glass deformation allow determining the deformation at the time of the onset of fracture. The analysis of the experimental data was supported by numerical simulations, using the AUTODYN commercial hydro-code.     

复合材料新的热层合理论及其有限元方法研究

本文基子三维各向异性热传导方程和复合材料的一般层合理论,推导出复合材料层合结构瞬态温度场分析的新的热层合理论,并依据此理论建立了简单、实用的有限元格式。数值算例表明：基于热层合理论的有限元方法有较好的精度,同时又比传统的分析方法更简便、有效。     

深圳星河世纪结构方案优选

高楼结构设计,包含结构方案选定、构件内力计算、杆件和节点构造措施等三 部分内容。工程实践经验表明,高楼结构设计能否做到安全、经济、合理,关键在于选定的结 构方案是否恰当。围绕结构方案优化这一主题,探讨了以深圳星河世纪A栋办公楼为例, 就其有关的安全、经济、合理各方面进行系统的阐述,以供同类建筑在确定结构方案时参考。     

钢丝网水泥薄壳穹顶技术应用研究

结合实际工程,介绍了钢丝网水泥薄壳穹顶的施工特点及难点、以及施工管理方法,总结了施工工艺,与传统的罐室结构施工方法进行对比,发现该技术具有用料省、造价低,工期短、进度快,减少支架、节约模板数量,工作效率高等特点。并对罐室结构推广采用钢丝网水泥薄壳穹顶提出了改用粗直径、大网眼的钢丝网,增加肋梁箍筋,考虑设置通风降温装置等改进意见。     

Damage analysis of POZD coated square reinforced concrete slab under contact blast

High efficiency, environmental protection and sustainability have become the main theme of the development of the protection engineering, requiring that the components not only meet the basic functions, but also have chemical properties such as acid and alkali corrosion resistance and aging resistance. Polyisocyanate-oxazodone (POZD) polymer has the above characteristics, it also has the advantages of strong toughness, high strength and high elongation. The concrete slab sprayed with POZD material has excellent anti-blast performance. In order to explore the damage characteristics of POZD sprayed concrete slabs under the action of contact explosion thoroughly, the contact explosion test of POZD concrete slabs with different charges were carried out. On the basis of experimental verification, numerical simulation were used to study the influence of the thickness of the POZD on the blast resistance of the concrete slab. According to the test and numerical simulation results that as the thickness of the coating increases, the anti-blast performance of the concrete slab gradually increases, and the TNT equivalent required for critical failure is larger. Based on the above analysis, empirical expressions on normalized crater diameter, the normalized spall diameter and normalized spall diameter are obtained.     

船用复合材料与钢质高压气瓶比较设计

基于网络理论对船用复合材料高压气瓶进行了外形尺寸及厚度设计 ,并与按第三强度理论钢质气瓶的设计结果进行了比较 .结果显示 :钢制高压气瓶的重量是复合材料气瓶的重量的二十几倍     

长杆射弹对钢纤维混凝土靶开坑特性的实验研究

为考察射弹对钢纤维混凝土靶的侵彻特性,采用57mm轻气炮,进行了小尺寸模拟射弹对钢纤维混凝土靶(钢纤维的体积分数为2%)的侵彻实验。实验中观察了钢纤维混凝土靶的开坑形状,测量了射弹的击靶速度,并且采用注沙法测出靶体的开坑体积,计算出射弹对靶体的侵彻体积,得到了长杆射弹的动能与侵彻体积的关系。引入射弹单位面积的冲击动能和靶体单位侵彻体积的冲击动能,结合钢纤维混凝土靶的实验数据,考察了两者之间的关系。