Effect of organo-modified montmorillonite nanoclay on mechanical,thermal and ablation behavior of carbon fiber/phenolic resin composites

The mechanical, thermal and ablation properties of carbon phenolic (C-Ph) composites (Type-I) rein-forced with different weight percentages of organo-modified montmorillonite (o-MMT) nanoclay have been studied experimentally. Ball milling was used to disperse different weight (wt) percentages (0, 1,2,4,6 wt.％) of nanoclay into phenolic resin. Viscosity changes to resin due to nanoclay was studied. On the other hand, nanoclay added phenolic matrix composites (Type-II) were prepared to study the dispersion of nanoclay in phenolic matrix by small angle X-ray scattering and thermal stability changes to the matrix by thermogravimetric analyser (TGA). This data was used to understand the mechanical, thermal and ablation properties of Type-I composites. Inter laminar shear strength (ILSS), flexural strength and flexural modulus of Type I composites increased by about 29％, 12％and 7％respectively at 2 wt.％ addition of nanoclay beyond which these properties decreased. This was attributed to reduced fiber volume fraction (％Vf) of Type-I composites due to nanoclay addition at such high loadings. Mass ablation rate of Type-I composites was evaluated using oxy acetylene torch test at low heat flux (125 W/cm2) and high heat flux levels (500 W/cm2). Mass ablation rates have increased at both flux levels marginally up to 2 wt.％ addition of nanoclay beyond which it has increased significantly. This is in contrast to increased thermal stability observed for Type-I and Type-Ⅱ composites up to 2 wt.％addition of nanoclay. Increased ablation rates due to nanoclay addition was attributed to higher insulation effi-ciency of nanolcay, which accumulates more heat energy in limited area behind the ablation front and self-propagating ablation mechanisms triggered by thermal decomposition of organic part of nanoclay.     

纤维增强SiO2气凝胶隔热复合材料的制备及其性能

将无机陶瓷纤维与SiO2溶胶混合,经超临界干燥制备了SiO2气凝胶隔热复合材料。SiO2气凝胶纤细的骨架颗粒减少了固态热传导,纳米级孔减少了气体热传导和对流传热,同时无机陶瓷纤维减少了辐射传热。SiO2气凝胶复合材料具有良好的隔热性能,其200℃和800℃的热导率分别为0.017W/m.K和0.042W/m.K。纤维的加入提供了力学支撑,高温处理增强了气凝胶骨架强度,材料在常温和高温下均具有良好的力学性能,其常温的拉伸、弯曲和抗压强度分别为1.44MPa、1.31MPa和0.98MPa(10%应变),800℃的拉伸、弯曲和抗压强度分别为1.95MPa、1.80MPa和1.42MPa(10%应变)。     

二氧化硅气凝胶隔热复合材料的性能及其瞬态传热模拟

高马赫数、新型航天飞行器承载严重的气动加热环境,其隔热材料的性能与传热计算对飞行器热防护结构的优化和预测具有一定的指导意义.研究了二氧化硅气凝胶隔热复合材料的结构与性能,并进行了瞬态传热模拟.结果表明复合材料热导率仅为0.018W/m·K,瞬态传热模拟结果与考核测试值吻合,为预测和优化隔热材料提供了一定的依据.     

Light weight HTPB-clay nanocomposites(HCN)with enhanced ablation performance as inhibition materials for composite propellant

In the present study,organically modified Montmorillonite clay with polar moiety,the Cloisite 30B,is used for preparation of Hydroxyl terminated polybutadiene(HTPB)-clay nanocomposites(HCN)by dispersion of nanoclay in polymer matrix under high shear mixing.The nanocomposites thus prepared are evaluated in composite propellants as inhibitor material for their functional utility.Several inhibition formulations containing 5 wt％-15 wt％of nanoclay,with or without the conventional filler Sb2O3,were prepared.All these formulations were evaluated for their physical,mechanical,thermal,and ablative properties.Ablation rate and density of the compositions containing Cloisite 30B is around 23％and 5％lower respectively in comparison of the base composition.Strain capability of these compositions is twofold higher than that of base composition.These compositions have also been evaluated for their smoke generation tendency by measuring infra red(IR)attenuation in the wavelength range 1.3 μm-5.6 μm and 8 μm-13 μm and thereby compared with the base composition.The corresponding results confirmed that the compositions containing Cloisite 30B as filler have much lower IR attenuation than compositions with conventional filler,Sb2O3.Replacement of 5％Sb2O3 by nanoclay showed 8％reduction in IR attenuation rate which further reduced to 16％on replacement of 15％of Sb2O3.Interfacial bonding of HCN based inhibitors is also comparable or even better than conventional inhibitors.Precisely,the nanoclay composites with Cloisite 30B as filler exhibit all desirable properties of an inhibitor.     

Transverse relaxation characteristic and stress relaxation model considering molecular chains of HTPB coating based on pre-strained thermal aging

In order to accurately describe the transverse relaxation characteristic and stress relaxation modulus of HTPB coating during pre-strain thermal aging process, a one month thermal aging test was carried out at 70 C with pre-strain of 0％, 3％, 6％ and 9％, respectively. The low-field 1H NMR and stress relaxation modulus tests were carried out for HTPB coating at different aging stages. The stress relaxation model considering the molecular chains was proposed according to the changes of crosslinking chain and dangling chain of HTPB coating during pre-strain aging. The results showed that with the increase of aging time, the decay rate of transverse relaxation curve became faster, the transverse relaxation time decreased, the value of combined parameter qMrl increased, the proportion of crosslinking chain decreased, while the proportion of dangling chain increased. Moreover, the stress relaxation modulus increased, the crosslinking network structure of HTPB coating became denser and the degree of cross-linking increased. At the initial aging stage, the pre-strain will destroy the crosslinking network structure of HTPB coating to a certain extent. With the increase of aging time, the effect of pre-strain will gradually weaken and the influence of aging on materials will gradually increase. The correlations between the stress relaxation model considering the molecular chains and the test results were more than 0.9950, which can accurately describe the stress relaxation modulus of HTPB coating during the pre-strain thermal aging process.     

列车用复合材料阻燃性能研究

不同类别的阻燃剂配合使用能产生协效作用,大大提高阻燃效果。在甲基丙烯酸类不饱和聚酯树脂9001基体中,添加微囊化红磷/氢氧化铝/三氧化二锑/甲基膦酸二甲酯(MRP/Al(OH)3/Sb2O3/DMMP)阻燃剂体系,对其树脂体系固化物及玻璃纤维织物复合材料的力学性能和阻燃性能进行了实验研究,提出了一种有望用于列车复合材料大尺寸构件制造的性能优异、价格低廉的新体系。结果表明,当质量添加比例分别为12%MRP、50%Al(OH)3、2%Sb2O3时,树脂体系室温粘度100mPa.s左右,凝胶时间超过80min,适用于RTM和VIMP等大尺寸构件成型工艺;复合材料拉伸强度215.4MPa,弯曲强度177.15MPa,拉伸模量13.85GPa,弯曲模量13.36GPa,氧指数39.7。     

Effect of functionally-graded interphase on the elasto-plastic behavior of nylon-6/clay nanocomposites; a numerical study

In nanocomposites, the interphase thickness may be comparable to the size of nano-particles, and hence, the effect of interphase layers on the mechanical properties of nanocomposites may be substantial. The interphase thickness to the nano-particle size ratio and properties variability across the interphase thickness are the most important affecting parameters on the overall behavior of nanocomposites. In this study, the effect of properties variability across the interphase thickness on the overall elastic and elasto-plastic properties of a polymeric clay nanocomposite (PCN) using a functionally graded (FG) interphase is investigated in detail. The results of the computational homogenization on the mesoscopic level show that Young's modulus variation of the interphase has a significant effect on the overall elastic response of nanocomposites in a higher clay weight ratio (Wt). Moreover, strength variation through the interphase has a notable effect on the elasto-plastic properties of PCNs. Also, the increase or decrease in stiffness of interphase from clay to matrix and vice versa have a similar effect in the overall behavior of nanocomposites.     

界面热阻对金刚石/银复合材料导热率的影响

研究了金刚石／银复合材料的导热率与金刚石的含量、粒度等之间的关系,着重讨论了界面热阻对复合材料导热率的影响。并阐述了金刚石表面镀钛,能有效改善金刚石对银的润湿性,降低界面热阻,从而提高金刚石／银复合材料的导热率。     

Magnetic,thermal stability and dynamic mechanical properties of beta isotactic polypropylene/natural rubber blends reinforced by NiZn ferrite nanoparticles

The dispersion of magnetic nanoparticles in matrix is crucial to ensure optimum performance of the composite. The difficulty level of achieving good dispersion is further increase when a multi-phases of matrix is present. A pre-coating technique of magnetic nanoparticles with polypropylene using ball-mill prior to melt-blending process was employed to prepare a multi-phases thermoplastic natural rubber composite. The effect of filler loading (2 wt%-10 wt%) on morphology, structure, magnetic properties, thermal stability and dynamic mechanical properties of the composites were investigated. It was found that the NiZn ferrite nanoparticles act as nucleating agent to form beta isostatic polypropylene thermoplastic composites. The composites' magnetic properties are directly dependent on the filler concentration. The dispersion of magnetic fillers in polymer matrix plays role in affecting the magnetic properties and thermal stability. The preference of filler to locate at amorphous phase has distorted the chain orientation of natural rubber and polypropylene. Hence, the polymorphism and crystallinity of the matrix varied as the filler loading increased, affecting the dynamic mechanical properties. It was found that 8 wt% NiZn nanocomposite exhibits highest E’ and tanδ, indicating the dynamic mechanical properties of NiZn nanocomposite are affected by β-phase degree.     

Preparation and characterization of HMX/EVA/hBNNSs micro-composites with improved thermal stability and reduced sensitivity

Hexagonal boron nitride nanosheets(HBNNSs)have huge potential in the field of coating materials owing to their remarkable chemical stability,mechanical strength and thermal conductivity.Thin-layer hBNNSs were obtained by a liquid-phase exfoliation of h-BN powders and incorporated into EVA coatings for improving the safety performance of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX).HBNNSs and ethylene-vinyl acetate copolymer(EVA)were introduced to HMX by a solvent-slurry process.For com-parison,the HMX/EVA and HMX/EVA/graphene(HMX/EVA/G)composites were also prepared by a similar process.The morphology,crystal form,surface element distribution,thermal decomposition property and impact sensitivity of HMX/EVA/hBNNSs composites were contrastively investigated.Results showed that as prepared HMX/EVA/hBNNSs composites were well coated with hBNNSs and EVA,and exhibited better thermal stability and lower impact sensitivity than that of HMX/EVA and HMX/EVA/G composites,suggesting superior performance of desensitization of hBNNSs in explosives.     

添加SiC微粉对硅树脂先驱体转化3D Cf/Si-O-C材料性能的影响

以三维碳纤维织物和廉价的硅树脂为原料,采用先驱体转化工艺制备3D G/Si-O-C材料,考察了浸渍液中添加SiC填料对材料微观结构、力学性能和抗氧化性能影响.结果表明:添加适量的SiC填料有助于减少基体孔隙,改善界面结合,从而提高材料的力学性能;而SiC含量过高时,容易在材料内部形成闭孔,从而导致材料力学性能下降.当SiC微粉含量为18.2%时,材料具有最好的力学性能,弯曲强度和断裂韧度分别为421.3MPa和13.0 MPa·m1/2;而材料的抗氧化性能随着SiC微粉含量的增加而增加,当SiC微粉含量为25.0%时,材料的弯曲强度保留率最高,达到了89.5%.     

先驱体转化致密SiC纳米复合材料的制备及其热电性能

以聚碳硅烷和锑改性聚硅烷为先驱体,利用先驱体转化SiC材料的富余自由碳高温石墨化的微观结构演变特点,采用热压烧结、先驱体浸渍—裂解法以及退火工艺制备出先驱体转化SiC纳米复合材料。采用SEM、TEM、XRD和Raman等测试手段表征和分析了相组成和微观结构,讨论了样品的热导率、电导率和塞贝克系数等热电参数随温度变化关系。研究表明,所得致密SiC纳米复合材料为n型热电材料。由于纳米石墨的作用,材料热导率抑制在4–8W/(m?K)范围。1600°C退火处理能够降低热导率,同时提高电导率和塞贝克系数绝对值,使先驱体转化法得到的SiC纳米复合材料无量纲热电优值ZT达到0.0028（650°C）,高于其他已报道的致密SiC/C复合材料和纳米复合材料体系。     

树脂浸渍裂解对气相硅反应渗透C/SiC的影响

粘胶基碳纤维毡经过CVD工艺进行沉积碳增密处理后,采用酚醛树脂浸渍—裂解对C/C素坯的密度进行调节,通过气相硅渗透反应工艺制备了C/SiC复合材料。研究了树脂浸渍—裂解对C/C素坯密度和气孔率的影响规律,分析了树脂裂解碳对C/SiC显微形貌和力学性能的影响。结果表明:随着树脂浸渍—裂解循环次数的增加,素坯密度增加,孔隙率降低;裂解碳含量为27wt%时,C/SiC复合材料的强度和模量达到最大,分别为231MPa和209GPa。通过控制裂解碳含量,可以实现对C/SiC复合材料力学性能和微观结构的裁剪。     

极性基团对环氧树脂基体力学性能及吸水特性的影响

研究了CYD- 128/THPA/DMP- 30 (CTD)、TDE- 85/THPA/DMP- 30(TTD)、CYD- 128/IPDA(CI)与TDE- 85/IPDA (TI)4种环氧树脂基体浇铸体的拉伸、弯曲和耐海水性能,分析了树脂、固化剂类型和分子结构对树脂基体性能的影响.结果表明,使用相同固化剂时,TDE...     

Modeling mechanical behaviors of composites with various ratios of matrixeinclusion properties using movable cellular automaton method

Two classes of composite materials are considered: classical metaleceramic composites with reinforcing hard inclusions as well as hard ceramics matrix with soft gel inclusions. Movable cellular automaton method is used for modeling the mechanical behaviors of such different heterogeneous materials. The method is based on particle approach and may be considered as a kind of discrete element method. The main feature of the method is the use of many-body forces of inter-element interaction within the formalism of simply deformable element approximation. It was shown that the strength of reinforcing particles and the width of particle-binder interphase boundaries had determining influence on the service characteristics of metaleceramic composite. In particular, the increasing of strength of carbide inclusions may lead to significant increase in the strength and ultimate strain of composite material. On the example of porous zirconia ceramics it was shown that the change in the mechanical properties of pore surface leads to the corresponding change in effective elastic modulus and strength limit of the ceramic sample. The less is the pore size, the more is this effect. The increase in the elastic properties of pore surface of ceramics may reduce its fracture energy.     

Influence of Al2O3 particles on the microstructure and mechanical properties of copper surface composites fabricated by friction stir processing

The influence of three factors, such as volume percentage of reinforcement particles (i.e. Al₂O₃), tool tilt angle and concave angle of shoulder, on the mechanical properties of Cu–Al₂O₃ surface composites fabricated via friction stir processing was studied. Taguchi method was used to optimize these factors for maximizing the mechanical properties of surface composites. The fabricated surface composites were examined by optical microscope for dispersion of reinforcement particles. It was found that Al₂O₃ particles are uniformly dispersed in the stir zone. The tensile properties of the surface composites increased with the increase in the volume percentage of the Al₂O₃ reinforcement particles. This is due to the addition of the reinforcement particles which increases the temperature of recrystallization by pinning the grain boundaries of the copper matrix and blocking the movement of the dislocations. The observed mechanical properties are correlated with microstructure and fracture features.     

An efficient SPH methodology for modelling mechanical characteristics of particulate composites

Particulate composites are one of the widely used materials in producing numerous state-of-the-art components in biomedical, automobile, aerospace including defence technology. Variety of modelling techniques have been adopted in the past to model mechanical behaviour of particulate composites. Due to their favourable properties, particle-based methods provide a convenient platform to model failure or fracture of these composites. Smooth particle hydrodynamics (SPH) is one of such methods which demonstrate excellent potential for modelling failure or fracture of particulate composites in a Lagrangian setting. One of the major challenges in using SPH method for modelling composite materials depends on accurate and efficient way to treat interface and boundary conditions. In this paper, a master-slave method based multi-freedom constraints is proposed to impose essential boundary conditions and interfacial displacement constraints in modelling mechanical behaviour of composite materials using SPH method. The proposed methodology enforces the above constraints more accurately and requires only smaller condition number for system stiffness matrix than the procedures based on typical penalty function approach. A minimum cut-off value-based error criteria is employed to improve the compu-tational efficiency of the proposed methodology. In addition, the proposed method is further enhanced by adopting a modified numerical interpolation scheme along the boundary to increase the accuracy and computational efficiency. The numerical examples demonstrate that the proposed master-slave approach yields better accuracy in enforcing displacement constraints and requires approximately the same computational time as that of penalty method.     

表面官能化对碳纳米管/环氧复合材料玻璃化转变温度及韧性的影响

通过碳纳米管的不同表面官能化,构造其与环氧树脂的不同界面。采用动态机械性能分析研究不同表面官能化碳纳米管对环氧树脂复合材料玻璃化转变温度的影响;采用摆锤冲击试验研究环氧树脂复合材料的韧性。结果表明:与纯环氧树脂相比,氨基化碳纳米管/环氧树脂复合材料的玻璃化转变温度升高,而羧基化碳纳米管/环氧树脂复合材料的玻璃化转变温度反而有所下降;碳纳米管/环氧树脂复合材料的冲击强度相比纯环氧树脂均提高了近一倍。复合材料性能的这些变化规律主要归因于不同表面官能化碳纳米管与环氧树脂基体间形成了不同的界面。     

The effect of al particle size on thermal decomposition,mechanical strength and sensitivity of Al/ZrH2/PTFE composite

To study the thermal decomposition of Al/ZrH2/PTFE with different Al particle size as well as mechanical strength and impact sensitivity under medium and low strain rates, molding-vacuum sintering was adopted to prepare four groups of power materials and cylindrical specimens with different Al particle size. The active decomposition temperature of ZrH2 was obtained by TG-DSC, and the quasi-static me-chanics/reaction characteristics as well as the impact sensitivity of the specimen were studied respec-tively by quasi-static compression and drop-hammer test. The results show that the yield strength of the material decreased with the increase of the Al particle size, while the compressive strength, failure strain and toughness increased first and then decreased, which reached the maximum values of 116.61 MPa, 191％, and 119.9 MJ/m respectively when the Al particle size is 12—14μm because of particle size grading. The specimens with the highest strength and toughness formed circumferential open cracks and reacted partly when pressed. Those with developmental cracks formed inside did not react. It is considered that fracture of specimens first triggered initial reaction between Al and PTFE to release an amount of heat. Then ZrH2 was activated and decomposed, and participated in subsequent reaction to generate ZrC. The impact sensitivity of the specimens decreased with the increase of Al particle size.     

Investigation of the mechanical and ballistic properties of hybrid carbon/ aramid woven laminates

High-performance ballistic fibers, such as aramid fiber and ultra-high-molecular-weight polyethylene (UHMWPE), are commonly used in anti-ballistic structures due to their low density, high tensile strength and high specific modulus. However, their low modulus in the thickness direction and insufficient shear strength limits their application in certain ballistic structure. In contrast, carbon fiber reinforced epoxy resin matrix composites (CFRP) have the characteristics of high modulus in the thickness direction and high shear resistance. However, carbon fibers are rarely used and applied for protection purposes. A hybridization with aramid fiber reinforced epoxy resin matrix composites (AFRP) and CFRP has the potential to improve the stiffness and the ballistic property of the typical ballistic fiber composites. The hybrid effects on the flexural property and ballistic performance of the hybrid CFRP/AFRP laminates were investigated. Through conducting mechanical property tests and ballistic tests, two sets of reliable simulation parameters for AFRP and CFRP were established using LS-DYNA software, respectively. The experimental results suggested that by increasing the content of CFRP that the flexural properties of hybrid CFRP/AFRP laminates were enhanced. The ballistic tests’ results and the simulation illustrated that the specific energy absorption by the perforation method of CFRP achieved 77.7% of AFRP. When CFRP was on the striking face, the shear resistance of the laminates and the resistance force to the projectiles was promoted at the initial penetration stage. The proportion of fiber tensile failures in the AFRP layers was also enhanced with the addition of CFRP during the penetration process. These improvements resulted in the ballistic performance of hybrid CFRP/AFRP laminates was better than AFRP when the CFRP content was 20 wt% and 30 wt%.