Study of simple plane wave generator with an air-metal barrier

Plane wave generators (PWGs) are used to accelerate flyer plates to high velocities with their generated plane waves, which are widely used in the test of dynamic properties of materials. The traditional PWG is composed of two explosives with different detonation velocities. It is difficult to implement the related fabrication processes and control the generated waves due to its complicated structures. A simple plane wave generator is presented in this paper, which is composed of two identical cylindrical high explosive (HE) charges and an air-metal barrier. A theoretical model was established based on two different paths of the propagation of detonation waves, based on which the size of air-metal barrier was calculated for a given charge. The corresponding numerical simulations were also carried out by AUTODYN-2D^® based on the calculated results, which were used to compare with the theoretical calculations. A detonation wave with a flatness of 0.039 μs within the range of 70-percent diameter of the main charge was obtained through the simulations.     

直接挤出成型用环氧树脂的流变性及其可打印性

直接挤出成型制造适用于任何含或不含添加剂的膏状或凝胶状复合材料,对复合材料制造技术具有深远意义。通过探讨热固性环氧树脂的流变学行为与挤出成型特性,得出热固性环氧树脂在直接挤出成型制造应用中的通用性流变学参数。通过向复合材料中加入增稠剂,对其流变学行为进行设计。结果表明:在高剪切速率(50 s~(-1))和低剪切速率(0.01 s~(-1))下,添加30%纳米黏土的环氧树脂的流变学行为较适合挤出式3D打印工艺。利用龙门式气动挤出式3D打印机,对复合材料的打印成型质量进行试验分析和验证。结合试验结果探讨了喷头高度对复合材料成型质量的影响,并且提出适用于喷头高度临界值的计算方法。探讨了挤出率、剪切速率等因素对成型质量的作用规律。针对多层打印问题,提出包含补偿系数的多层打印的临界喷头高度的计算方法。以上研究对促进基于复合材料的挤出式3D打印具有积极意义。     

Preparation of reduced sensitivity co-crystals of cyclic nitramines using spray flash evaporation

The present day weapon technology demands novel energetic materials that exhibit simultaneous high explosive yield and reduced sensitivity. This article demonstrates application of spray evaporation to prepare reduced sensitive co-crystals of high performance nitramine explosives like HMX and CL-20 with a relatively less insensitive explosive 1,1-diamino-2,2-dinitroethylene or FOX-7. Stronger intermolecular hydrogen bonding in FOX-7 is responsible for limited solubility in most of organic solvents. Large solubility differences of FOX-7 with HMX and CL-20 restricts it's co-crystallization through classical methods that yields thermodynamically favorable product. Spray flash evaporation, a kinetic crystallization method, has been therefore adopted and could successfully produce CL-20/FOX-7 (2:1) and HMX/FOX-7 (4:1) co-crystals. The fine powdered materials obtained were characterized by SEM, powder XRD, Raman spectroscopy, DSC-TGA etc. Multipoint Raman spectra showed consistent occurrence of spectral features indicating stoichiometric co-existence of ingredients in the crystal lattices. DSC analysis showed absence of all thermally assisted solid-solid phase transformation in the co-crystals as they were observed in pristine materials. The thermal stability calculated in terms of activation barrier for decomposition, revealed the CL-20/FOX-7 co-crystal to be intermediately stable on comparison to their constituents while, the HMX/FOX-7 co-crystal is more stable. Compared to pure HMX and CL-20, both the co-crystals have shown higher insensitivity to impact force, suggesting them to be suitable for future generation insensitive munitions.     

Scale-up synthesis and characterization of 2,6-diamino-3,5-dinitropyrazine-1-oxide

2,6-diamino-3,5-dinitropyrazine-1-oxide (ANPZO), as an insensitive high explosive, with a high yield and excellent purity has been prepared at pilot plant scale by an improved method. The synthesized ANPZO is characterized by IR, laser granularity measurement, SEM and HPLC. The particle analysis revealed that the improved method could offer desired product with average particle size of 40 μm and high purity (>98.45%). The experimental parameters exhibited that the detonation velocity of the formulation based on ANPZO was higher than that of the corresponding TATB formulation. The DSC curve showed that the exothermic decomposition of the product occurred at the temperature between 300.5 °C and 360.4 °C. Furthermore, the sensitivity test suggests its safe nature towards mechanical stimulus.     

Performances and direct writing of CL-20 based ultraviolet curing explosive ink

A new type of explosive ink formulation that can be quickly cured was prepared with unsaturated polyester as binder,styrene as active monomer,2,4,6-trimethylbenzoyl-diphenylphosphine oxide as photoinitiator,and hexanitrohexaazaisowurtzitane (CL-20) as the main explosive.Then the explosive ink direct writing technology was used to charge the micro-sized energetic devices,the curing mechanism of the explosive ink was discussed,and the microstructure,safety performance and explosive transfer performance of the explosive ink molded samples were tested and analyzed.Results indicate that the composite material has a fast curing molding speed,its hardness can reach 2H within 8 min.The crystal form of CL-20 in the molded sample is still ε type.The CL-20 based W-curing explosive ink formulation has good compatibility,its apparent activation energy is increased by about 3.5 kJ/mol.The composite presents a significant reduction in impact sensitivity and its characteristic drop height can reach 39.8 cm,which is about 3 times higher than the raw material.When the line width of charge is 1.0 mm,the critical thickness of the explosion can reach 0.015 mm,and the explosion velocity is 7129 m/s when the charge density is 1.612 g/cm3.     

Liquid phase in-situ synthesis of LiF coated boron powder composite and performance study

Among practical metal additives, boron (B) has a high volumetric heating value, making it a promising choice as a fuel additive. Although B can theoretically yield a large amount of energy upon complete combustion, its combustion is retarded by the initial presence of B oxide, which coats the surfaces of B particle. To improve the ignition and combustion properties of B powder, LiOH and NH₄F were used as precursors to synthesize uniformly LiF-coated B composites (LiF-B) in situ. The LiF-B mixture was also prepared for comparison using a physical method. X-ray diffraction (XRD), Fourier-transform infrared (FTIR), scanning electron microscope (SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to characterize the morphologies and compositions of the products. The thermal and combustion properties of the samples were characterized by thermal gravity-differential thermal gravity (TG-DTG), differential scanning calorimetry (DSC) and closed bomb experiment. The XRD, FTIR, SEM and EDS results demonstrated the successful preparation of the coated LiF-B sample. The TG-DTG and closed bomb experiment results indicated that the addition of LiF decreased the ignition temperature of B powder, and increasing its reaction efficiency. DSC results show that when LiF-B was added, the released heat of underwater explosive increased by 6727.2, 7280.4 and 3109.6 J/g at heating rates of 5, 10, and 15 °C/min, respectively. Moreover, LiF-B decreased the activation energy of secondary combustion reaction of explosive system as calculated through Kissinger's method by 28.9%, which indicated an excellent catalytic effect for the thermal decomposition of underwater explosive. The results reveal that LiF can improve the combustion efficiency of B powder, thereby increasing the total energy of explosives. The mechanical sensitivity increased slightly after adding LiF-B to the underwater explosive. Compared to the underwater explosive with added B, the mechanical sensitivity of the explosive with added LiF-B was significantly lower.     

纺织涂层行业消防安全现状及对策研究

纺织涂层工艺是纺织行业深加工不可缺少的组成部分,纺织涂层行业在带来经济效益的同时,也带来了诸多安全生产隐患。简要介绍了纺织涂层技术,分析了纺织涂层行业的火灾危险性,从完善安全技术法规、完善安全管理体系、建立安全管理机构、严格审批等方面提出了相应的消防安全对策和建议。     

飞行器涂层防热选材、设计与应用

就防热材料选材、设计,主要是涂层设计原理和设计过程中需要考虑的一些问题浅谈了一些体会,对变密度非稳态的、有机/无机杂化防热涂层材料的热导率计算等参数辨识方法原理作了初步探讨,还介绍了几种热防护涂层(TPC)的性能、应用情况和防热效果.     

A novel method for determination of lethal radius for high-explosive artillery projectiles

A new model has been defined that enables the estimation of the lethal radius (radius of efficiency) of HE (High Explosive) artillery projectiles against human targets. The model is made of several modules: CAD (Computer Aided Design) modeling, fragment mass distribution estimation, fragment initial velocity prediction, fragment trajectory calculation, effective fragment density estimation, and high explosive projectile lethal radius estimation. The results were compared with the experimental results obtained based on tests in the arena used in our country, and the agreement of the results was good. This model can be used in any terminal-ballistics scenario for high explosive projectiles since it is general, para-metric, fast and relatively easy to implement.     

自蔓延反应喷涂表面涂层技术进展

围绕自蔓延反应喷涂技术与工艺研究和自蔓延反应喷涂相关理论研究两个方面,介绍了这一技术领域的发展状况。SHS反应喷涂技术将燃烧合成与传统热喷涂相融合,将各类高化学能的反应型粉材、线材引入喷涂技术中制备高性能陶瓷和金属间化合物涂层,发展了SHS反应药芯线材电弧喷涂、SHS等离子喷涂、爆炸反应喷涂以及SHS反应火焰喷涂等技术手段。一方面,对其中的配系设计、控制参数、涂层性能和相关设备等方面开展了深入的实验研究;另一方面,围绕涂层形成过程、喷涂条件下的反应机理与模式,以及反应喷涂过程中的能量状态和粒子的物理状态等方面开展了初步的理论研究,正在构筑较完整的理论体系。     

Formation and characterization of core-shell CL-20/TNT composite prepared by spray-drying technique

The core-shell 2,4,6,8,10,12-Hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane/2,4,6-Trinitrotoluene (CL-20/TNT) composite was prepared by spray-drying method in which sensitive high energy explosive (CL-20) was coated with insensitive explosive (TNT). The structure and properties of different formulations of CL-20/TNT composite and CL-20/TNT mixture were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Laser particle size analyzer, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), differential scanning calorimetry (DSC), impact sensitivity test and detonation performance. The results of SEM, TEM, XPS and XRD show that ϵ-CL-20 particles are coated by TNT. When the ratio of CL-20/TNT is 75/25, core-shell structure is well formed, and thickness of the shell is about 20–30 nm. And the analysis of heat and impact show that with the increase of TNT content, the TNT coating on the core-shell composite material can not only catalyze the thermal decomposition of core material (CL-20), but also greatly reduce the impact sensitivity. Compared with the CL-20/TNT mixture (75/25) at the same ratio, the characteristic drop height of core-shell CL-20/TNT composite (75/25) increased by 47.6% and the TNT coating can accelerate the nuclear decomposition in the CL-20/TNT composites. Therefore, the preparation of the core-shell composites can be regarded as a unique means, by which the composites are characterized by controllable decomposition rate, high energy and excellent mechanical sensitivity and could be applied to propellants and other fields.     

Surface modification of ammonium nitrate by coating with surfactant materials to reduce hygroscopicity

Ammonium nitrate (AN) is promising oxidizer in green propellants. In this work, the physical coating method was improved to modify the surface of ammonium nitrate particles with different surfactant materials to reduce hygroscopicity. Cetylalcohol, stearic acid, stearyl alcohol, palmic acid, lauric acid, stearsmide, tetradecylamine, dodecylamine, and tetradecanol were used as coating surfactant agents. The hygroscopicity was tested for ammonium nitrate with and without coating. Fourier transform infrared (FTIR) and scanning electron microscopy (SEM) were used to characterize the surface of coated and uncoated ammonium nitrate. The mass ratio of coating layer and decline of absorption rate of ammonium nitrate coated by cetylalcohol were 1.00%, and 28.40%, respectively. The results indicate that coating with cetylalcohol surfactant have advantages over the other surfactants in term of low mass ratio of coating layer, and high decline of moisture absorption rate. Thus, cetylalcohol would be a promising coating surfactant material for ammonium nitrate. The idea and approach presented in this study have potential to made hydrophobic layer on the surface of particles to reduce hygroscopicity of AN, and also help the researcher to improving anti-hygroscopicity of ammonium salts.     

Field test and probabilistic analysis of irregular steel debris casualty risks from a person-borne improvised explosive device

Person-borne improvised explosive devices (PBIEDs) are often used in terrorist attacks in Western countries. This study aims to predict the trajectories of PBIED fragments and the subsequent safety risks for people exposed to this hazard. An explosive field test with a typical PBIED composed of a plastic explosive charge and steel nut enhancements was performed to record initial fragment behaviour, including positions, velocity, and trajectory angles. These data were used to predict the full trajectory of PBIED fragments using a probabilistic analysis. In the probabilistic analyses a probability of fatality or serious injury was computed. Based on the results presented, many practical conclusions can be drawn, for instance, regarding safe evacuation distances if a person were exposed to a suspected PBIED.     

Direct ink writing of 3D-Honeycombed CL-20 structures with low critical size

3D-Honeycombed CL-20 structures with low critical size of detonation have been fabricated successfully for intelligent weapon systems using a micro-flow direct ink writing (DIW) technology. The CL-20-based explosive ink for DIW technology was prepared by a two-component adhesive system with waterborne polyurethane (WPU) and ethyl cellulose (EC). Not only the preparation of the explosive ink but also the principle of DIW process have been investigated systematically. The explosive ink displayed strong shear-thinning behavior that permitted layer-by-layer deposition from a fine nozzle onto a substrate to produce complex shapes. The EC content was varied to alter the pore structure distribution and rheological behavior of ink samples after curing. The deposited explosive composite materials are of a honeycombed structure with high porosity, and the pore size distribution increases with the increase of EC content. No phase change was observed during the preparation process. Both WPU and EC show good compatibility with CL-20 particles. Apparently high activation energy was realized in the CL-20-based composite ink compared with that of the refined CL-20 due to the presence of non-energetic but stable WPU. The detonation performance of the composite materials can be precisely controlled by an adjustment in the content of binders. The 3D honeycombed CL-20 structures, which are fabricated by DIW technology, have a very small critical detonation size of less than 69 μm, as demonstrated by wedge shaped charge test. The ink can be used to create 3D structures with complex geometries not possible with traditional manufacturing techniques, which presents a bright future for the development of intelligent weapon systems.     

Electronic warfare in the optical band: Main features,examples and selected measurement data

The paper presents the possibilities of, and methods for, acquiring, analysing and processing optical signals in order to recognise, identify and counteract threats on the contemporary battleground. The main ways electronic warfare is waged in the optical band of the electromagnetic wave spectrum have been formulated, including the acquisition of optical emitter signatures, as well as ultraviolet (UV) and thermal (IR) signatures. The physical parameters and values describing the emission of laser radiation are discussed, including their importance in terms of creating optical signatures. Moreover, it has been shown that in the transformation of optical signals into signatures, only their spectral and temporal parameters can be applied. This was confirmed in experimental part of the paper, which includes our own measurements of spectral and temporal emission characteristics for three types of binocular laser rangefinders. It has been further shown that through simple registration and quick analysis involving comparison of emission time parameters in the case of UV signatures in “solar-blind” band, various events can be identified quickly and faultlessly. The same is true for IR signatures, where the amplitudes of the recorded signal for several wavelengths are compared. This was confirmed experimentally for UV signatures by registering and then analyzing signals from several events during military exercises at a training ground, namely Rocket Propelled Grenade (RPG) launches and explosions after hitting targets, trinitrotoluene (TNT) explosions, firing armour-piercing, fin-stabilised, discarding sabots (APFSDS) or high explosive (HE) projectiles. The final section describes a proposed model database of emitters, created as a result of analysing and transforming the recorded signals into optical signatures.     

陶瓷/金属梯度热障涂层的制备及性能评价

为了评价陶瓷/金属梯度热障涂层的性能,设计了4种涂层方案和2种基体材料(1Cr18Ni9Ti和2Cr13).利用单枪单送粉器成功地制备了线性梯度涂层.通过观察涂层的微观结构、测量涂层的抗热震性能和热残余应力来评价涂层的性能.利用扫描电镜对各种陶瓷涂层的微观结构进行了观察和分析,利用X射线能谱分析得到了陶瓷梯度涂层试样中的不同区域的衍射图.热震试验表明,梯度涂层比非梯度涂层具有更好的抗热震性能.采用钻孔法对不同涂层方案进行了残余应力的测量,结果表明,压应力出现在1Cr18Ni9Ti基体材料上,而拉应力出现在2Cr13基体材料上.     

Thermal and combustion behavior of Al-MnO2 nanothermite with poly(vinylidene fluoride -co- hexafluoropropylene) energetic binder

Fluoropolymers get increasing attention in energetic materials application due to the high fluorine content. To explore the effect of poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) on Al/MnO2 nanothermite, the samples with different contents are prepared and characterized by SEM, TG-DSC, XRD, and their ignition and combustion behavior are tested and recorded. The results show that P(VDF-HFP) as an energetic binder can combine the nanothermite components together, even exist in the gaps. The integrity of energetic materials has been improved. Thermal analysis shows that the addition of P(VDF-HFP) greatly changes the thermal reaction processes, and the exothermic peaks appear early, but the utilization of fuel and oxidizer is not efficient from the XRD results. Furthermore, the appropriate addition of P(VDF-HFP) can directly reduce the ignition energy threshold and increase the combustion time, which is necessary for the potential ignition charge application. The possible reasons for above phenomena are discussed and analyzed. This research provides a reference for improvement of thermite-based ignition charge formulation.     

计算机辅助设计在BDP阻燃PC/ABS合金配方中的应用

在前人对BDP阻燃PC/ABS合金的实验研究基础上,借助计算机强大的运算能力辅助BDP阻燃PC/ABS合金进行了配方设计。根据BP三层感知器神经网络结构,确定了用于BDP以及BDP/SiO2复配体系阻燃PC/ABS合金配方建模的人工神经网络的输入、输出以及隐层模式,选用Sigmoid函数作为用于建模的BP网络各层的激活函数,以PC/ABS、SiO2和BDP三组分在配方中的比重作为三层BP人工神经网络的输入,通过设置3个隐层节点,建立以极限氧指数（LOI）或伸长率分别作为输出的单目标模型。经过利用9对试样分别作为训练样本和测试样本对网络进行训练、测试,当输出量设为极限氧指数（LOI）时,预测误差在±4%以内;当输出量设为伸长率时,预测误差在±5%以内,均能满足实用配方的要求。     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

焊条粘结剂及烘焙温度对药皮吸潮性的影响

通过试验研究了改进水玻璃及焊条烘焙温度对焊条药皮吸潮行为的影响.结果表明,在水玻璃中加入防水剂和/或丙烯酸甲酯,以及水玻璃低碱化处理均能明显提高焊条药皮的耐吸潮性;对于不同类型的水玻璃,通过选择适当的烘焙温度可有效地防止药皮吸潮.