Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

采用射流掺混增强的前可调面积涵道引射器数值模拟

为了提高风扇外涵和核心机驱动风扇级外涵流体的掺混效率,提出一种采用射流掺混增强的前可调面积引射器设计方案。通过数值模拟的手段对流量特性、流动掺混和总压损失等方面进行了研究,并同基准模型进行了对比分析,结果表明：采用波瓣混合器结构的前可调面积引射器设计,显著地增加了较高出口背压工况下风扇外涵的流通能力;新的设计方案不仅没有增加低出口背压工况下的总压损失,还减小了高背压出口工况下的流动损失;流向涡的特征尺度是提高掺混效率的关键,可以进一步优化波瓣混合器几何轮廓,以满足调节机构对结构设计的要求。     

直接力/气动力复合作用动能拦截弹姿态控制方法

针对直接力/气动力复合作用动能拦截弹的姿态控制问题,建立了拦截弹俯仰-偏航通道短周期运动模型;利用线性二次型最优跟踪控制理论结合姿控固体小火箭点火逻辑设计了复合控制系统,通过分析非线性容限得出了该系统对直接力偏差具有强鲁棒性的结论;姿控回路仿真表明系统具有快速响应特性及良好的跟踪性能,考虑侧喷干扰效应等实际条件的六自由度弹道仿真表明所设计的控制系统能够满足拦截末段直接碰撞要求。     

合成射流影响因素

在综合国外大量实验和数值模拟数据的基础上 ,对影响合成射流特性的驱动因素、结构因素进行了分析和总结 ,并且通过数值模拟的方法对雷诺数以及斯托罗哈数对合成射流的影响进行了研究。获得了反映合成射流激励器特征的函数关系式 ,为激励器的初步设计提供指导     

电荷泵中单粒子瞬变的研究

为分析电荷泵中不同频率单粒子瞬变(SET)电流对锁相环(PLL)的影响,采用频域分析法从增益和带宽的角度研究了环路参数与SET响应的关系。分析结果表明,减小环路滤波电阻可以降低系统增益,从而有效降低压控振荡器控制电压的扰动;增大固有频率或阻尼因子则可以提高系统带宽,从而滤除更大范围的SET电流,同时还可以降低PLL恢复到锁定状态的时间。因此,减小环路滤波电阻、增大固有频率或阻尼因子是有效的设计加固方法。通过1GHz PLL的SET模拟验证了上述结论。     

超燃冲压发动机燃烧室燃料喷注及其内流场的数值模拟

基于三维N-S方程,利用有限差分数值离散方法,对考虑了燃料喷注和凹腔结构综合影响的某超燃冲压发动机燃烧室模型的内流场进行了数值模拟,与实验流动图谱进行了定性比较,并进一步探讨了燃料喷注过程的非定常特性以及凹腔结构对流动的影响。研究表明:本文数值模拟的稳态时刻流场与实验流动图谱相似;数值结果捕捉到了横向喷注燃料沿下游运动并向凹腔扩散的非定常动态变化的规律。     

Optimal burn‐in procedure for periodically inspected systems

Burn‐in is a widely used method to improve the quality of products or systems after they have been produced. In this paper, we study burn‐in procedure for a system that is maintained under periodic inspection and perfect repair policy. Assuming that the underlying lifetime distribution of a system has an initially decreasing and/or eventually increasing failure rate function, we derive upper and lower bounds for the optimal burn‐in time, which maximizes the system availability. Furthermore, adopting an age replacement policy, we derive upper and lower bounds for the optimal age parameter of the replacement policy for each fixed burn‐in time and a uniform upper bound for the optimal burn‐in time given the age replacement policy. These results can be used to reduce the numerical work for determining both optimal burn‐in time and optimal replacement policy. © 2007 Wiley Periodicals, Inc. Naval Research Logistics, 2007     

助推器分离过程动态流场数值模拟

利用三维N-S方程,采用NND2M有限差分格式作为数值离散方法,对助推器与上面级分离过程的动态流场进行了数值模拟,分析了反作用推力火箭发动机的喷流对上面级弹体底部轴向作用力的影响。根据计算得到的变化规律发现,在分离距离较小的情况下,反推火箭喷流对上面级弹体的干扰作用明显,产生较大轴向作用力,对于上面级飞行稳定性有影响。     

新型优化同心筒自力发射流场机理与降温效果

针对同心筒自力发射结构优化与热环境改善的问题,基于雷诺平均方程及轴对称N-S方程,依托弹性变形和网格再生成方法结合的动网格技术,对3种不同结构形式同心筒发射装置的二维轴对称流场进行了非定常数值计算,得到了不同结构条件下动态的流场机理及导弹热环境特性。计算结果显示:导流器方案能实现燃气流迅速顺利排导;筒底收缩段设计能有效遮挡反溅燃气流;筒口导流板结构较好抑制了内筒的"倒吸效应",确保导弹和内筒的热安全;揭示了优化同心筒的流场结构与降温机理,可为相关研究提供参考。     

不同形状喷嘴内流场模拟分析

建立了前混合磨料水射流喷嘴内固液两相流动的数学模型,运用Fluent软件对圆柱型、圆锥收敛型、流线型和圆锥带圆柱段收敛型喷嘴内流场进行了数值模拟,分析了喷嘴形状对喷嘴内流场和磨料颗粒加速性能的影响,并通过切割实验验证了仿真结果的可靠性。结果表明:圆柱型喷嘴能量损耗较大,圆锥收敛型喷嘴对磨料颗粒的加速性能差,流线型喷嘴性能良好但不易加工,只有圆锥带圆柱段收敛型喷嘴是用作前混合式磨料水射流喷嘴的最优选择。