高温空气下C/SiC复合材料力学性能测试

测试了C/SiC复合材料在高温空气下的压缩、弯曲和拉伸性能,利用扫描电子显微镜分析复合材料在室温与高温条件下的断口微观形貌。结果表明:从室温升温到1 000 ℃测试温度时,C/SiC复合材料的压缩强度由247 MPa降低至78 MPa,性能降低68%;弯曲强度由480 MPa降低至277 MPa,性能降低42%;拉伸强度由247 MPa降低至152 MPa,性能降低38%。高温氧化导致界面退化,损伤材料基体与碳纤维结构,加剧了纤维断裂程度,改变了纤维与基体的结合状态,纤维增韧机制逐渐消失,导致复合材料性能下降。     

裂解温度对PIP制备2D Cf/Si-O-C复合材料结构与性能的影响

以二维碳纤维布、硅树脂先驱体、SiC微粉和乙醇溶剂为原料,采用先驱体转化工艺制备了2D Cf/Si-O-C复合材料,考察了裂解温度对材料结构和性能的影响。结果表明,首周期裂解温度对制备材料的力学性能有重要影响,纤维-基体间的界面弱化是复合材料力学性能提高的主要原因;第6周期采用合适的温度裂解可提高复合材料的力学性能,其弯曲强度和断裂韧性分别达到了263.9MPa和12.8MPa.m1/2。     

T300和JC2#纤维增强C/SiC复合材料力学性能对比

以聚碳硅烷(PCS)为先驱体,采用聚合物浸渍裂解法(PIP)分别制备得到T300碳纤维和JC2#碳纤维增强C/SiC复合材料。JC2#C/SiC复合材料具有优异的力学性能,抗弯强度和断裂韧性分别达到662MPa和19.5MPa.m1/2;T300 C/SiC复合材料表现出低强度、高脆性,其抗弯强度和断裂韧性不足前者的四分之一。T300 C/SiC复合材料低性能的根本原因在于T300纤维在PCS裂解过程中性能严重下降,复合材料中纤维与基体间存在强界面结合是另一个影响因素。     

不同裂解温度对制备SiCf/Si-O-C复合材料性能研究

以聚硅氧烷为先驱体,研究先驱体转化过程中在不同的裂解温度下对制备SiCf/Si-O-C复合材料性能影响.结果表明,当裂解温度在700℃、800℃时,陶瓷基复合材料的弯曲强度分别为255.2 MPa、309.0 MPa;当裂解温度在1000℃时,陶瓷基复合材料的弯曲强度为45.3 MPa.对SiCf/Si-O-C复合材料的微观结构及载荷-位移曲线进行分析,发现界面结构是影响SiCf/Si-O-C复合材料性能的主要因素.     

表面官能化对碳纳米管/环氧复合材料玻璃化转变温度及韧性的影响

通过碳纳米管的不同表面官能化,构造其与环氧树脂的不同界面。采用动态机械性能分析研究不同表面官能化碳纳米管对环氧树脂复合材料玻璃化转变温度的影响;采用摆锤冲击试验研究环氧树脂复合材料的韧性。结果表明:与纯环氧树脂相比,氨基化碳纳米管/环氧树脂复合材料的玻璃化转变温度升高,而羧基化碳纳米管/环氧树脂复合材料的玻璃化转变温度反而有所下降;碳纳米管/环氧树脂复合材料的冲击强度相比纯环氧树脂均提高了近一倍。复合材料性能的这些变化规律主要归因于不同表面官能化碳纳米管与环氧树脂基体间形成了不同的界面。     

石英纤维增强苯并噁嗪树脂复合材料研究

对苯并(啞心)嗪树脂应用于RTM工艺制备石英纤维增强复合材料进行了研究.系统考察了该树脂的工艺性能及力学性能,制备并测试了石英/苯并(啞心)嗪复合材料的力学性能及耐烧蚀性能,并将相关性能与钡酚醛与石英/钡酚醛进行了比较.结果表明,在85℃～145℃温度区间内苯并(啞心)嗪树脂粘度保持在800mPa·s以下,树脂具有较宽的低粘度温度平台和较长的低粘度保持时间.力学性能及耐烧蚀性能研究表明,石英/苯并(啞心)嗪复合材料的层间剪切强达到了61.5MPa,拉伸强度和弯曲强度显著优于石英,钡酚醛复合材料,质量烧蚀率和线烧蚀率分别为0.0510g·s-1和0.032mm·s-1.石英/苯并(啞心)嗪复合材料是一种可采用RTM工艺制备的耐烧蚀材料.     

高比重钨合金的烧结成形与组织性能研究

采用液相烧结成形工艺制备了90W-Ni-Fe合金棒,通过分析烧结态钨合金的组织形貌和力学性能,观察合金的断口组织形貌,研究了烧结工艺对高比重钨合金组织性能的影响,认为减少W-W界面,增加W-W界面的结合强度,是提高烧结态钨合金力学性能的有效途径。     

石英/双酚E型氰酸酯复合材料的制备与性能

采用实验方法研究双酚E型氰酸酯树脂的黏度和固化特性,揭示催化剂对双酚E型氰酸酯树脂固化特性的影响规律;采用树脂传递模塑和真空导入模塑工艺制备石英纤维/双酚E型氰酸酯复合材料,并考察其力学性能。结果表明,双酚E型氰酸酯树脂室温至90℃范围内的黏度小于300 m Pa·s,凝胶时间大于10 h,起始固化温度、固化温度和终止固化温度分别为186±5℃,235±5℃和286±5℃;固化特征温度随着催化剂含量的增加而降低,直至催化剂饱和,其饱和范围为0.02%~0.03%,可使双酚E型氰酸酯树脂体系的固化温度降低约60℃,从而避免爆聚,实现液相法成型其复合材料;真空导入模塑工艺制备的石英纤维/双酚E型氰酸酯复合材料的力学性能明显优于树脂传递模塑制备试样。     

聚碳硅烷／二乙烯基苯快速升温裂解制备Cf/SiC复合材料

以聚碳硅烷(PCS)/二乙烯基苯(DVB)为先驱体,采用快速升温裂解制备了3D-B Cf/SiC复合材料.结果证明:裂解升温速率的提高可以大大缩短制备周期,同时可以提高材料密度和形成较好的界面结合,从而提高材料的力学性能.制备得到的Cf/SiC材料室温弯曲强度达到556.7MPa.     

添加SiC微粉对硅树脂先驱体转化3D Cf/Si-O-C材料性能的影响

以三维碳纤维织物和廉价的硅树脂为原料,采用先驱体转化工艺制备3D G/Si-O-C材料,考察了浸渍液中添加SiC填料对材料微观结构、力学性能和抗氧化性能影响.结果表明:添加适量的SiC填料有助于减少基体孔隙,改善界面结合,从而提高材料的力学性能;而SiC含量过高时,容易在材料内部形成闭孔,从而导致材料力学性能下降.当SiC微粉含量为18.2%时,材料具有最好的力学性能,弯曲强度和断裂韧度分别为421.3MPa和13.0 MPa·m1/2;而材料的抗氧化性能随着SiC微粉含量的增加而增加,当SiC微粉含量为25.0%时,材料的弯曲强度保留率最高,达到了89.5%.     

INS/GPS/CNS组合导航系统仿真

在分析INS、GPS、CNS导航系统特点的基础上,建立了组合导航系统的误差模型,提出了一种基于联邦滤波器的INS/GPS/CNS的组合导航算法,采用平台失准角、INS与GPS的位置之差和速度之差作为观测量,对算法进行了仿真研究。仿真结果表明:通过校正惯导平台、消除导航参数误差,可以大大提高系统的导航精度。     

N2O/C7H8单喷嘴燃气发生器试验研究

以基于N2O/C7H8的燃烧驱动混合型气动CO2激光器点火试验为研究背景,设计了液态N2O供应系统及N2O/C7H8单喷嘴燃气发生器.对液态N2O供应系统、N2O/C7H8的点火及燃烧性能进行了研究.试验结果表明:设计的N2O供应系统能够实现液态N2O的稳定供应;在设定的时序下,两个设计工况(余氧系数分别为0.3和0....     

准陶瓷Cf/SiC复合材料的制备

采用热重-差热(TG-DTA)、红外(IR)等分析测试手段,研究了聚碳硅烷(PCS)的裂解及化学转化过程,从理论上验证了先驱体聚碳硅烷(PCS)600℃裂解产物的准陶瓷特性.先驱体聚碳硅烷在600℃呈现一种半有机、半无机状态,其产物具有准陶瓷的特征,在大约750℃出现无机化转变高峰,固称其为准陶瓷.以碳布、准三维编织体、三维编织体为增强体,采用先驱体浸渍裂解(PIP)工艺在600℃制备了碳纤维增强碳化硅(Cf/SiC)准陶瓷基复合材料.结果表明,以三维编织体增强的准陶瓷Cf/SiC复合材料获得了较理想的结构、性能,所制备3D-Cf/SiC复合材料密度仅有1.27g/cm3,弯曲强度达到193.69MPa,室温拉伸强度为197.69MPa,600℃拉伸强度为167.33MPa.复合材料断口形貌分析表明,在低温600℃制备的准陶瓷Cf/SiC复合材料呈现明显的韧性断裂特征.     

Reaction characteristic of PTFE/Al/Cu/Pb composites and application in shaped charge liner

In this paper, the reaction characteristic and its application in shaped charge warhead of a novel reactive material, which introduced copper (Cu) and plumbum (Pb) into traditional polytetrafluoroethylene/aluminum (PTFE/Al), are studied. The thermal analysis and chemical reaction behavior of the PTFE/Al/Cu/Pb mixture are investigated by Differential Scanning Calorimetry (DSC),Thermo-gravimetry (TG), and X-ray Diffraction (XRD) techniques. Then, the shaped charge liners with PTFE/Al/Cu/Pb reactive materials are fabricated, and the X-ray experiments show that they could form reactive jets with excellent performance under the detonation effects of the shaped charge. Based on that, the penetration experiments of shaped charge with PTFE/Al/Cu/Pb reactive liner against steel plates are carried out, and the results demonstrate that the PTFE/Al/Cu/Pb reactive jets could produce a deeper penetration depth compared to the traditional PTFE/Al reactive jets. Meanwhile, the PTFE/Al/Cu/Pb reactive jets also show significant inner-blast effects, leading to dramatically cracking or fragmentation behavior of the penetrated steel plates. This new PTFE/Al/Cu/Pb reactive liner shaped charge presents enhanced penetration behavior for steel targets that incorporates the penetration capability of a high-density and ductility jet, and the chemical energy release of PTFE-matrix reactive materials.     

随机环境中的M/MY/1排队系统

文献［４］讨论了随机环境中的Ｍ／Ｍ／１排队模型，本文提出和讨论随机环境中的Ｍ／Ｍｙ／１排队模型，在统计平衡条件下给出了队长和等待队长的平稳分布以及平均队长和平均等待队长，得到了等待时间和逗留时间分布以及平均等待时间和平均逗留时间。     

基于SINS/DVL/GPS的AUV组合导航技术

为了提高自主水下航行器组合导航系统的精度,选择了捷联式惯性导航系统(SINS)和多普勒速度声纳(DVL)导航为主、GPS卫星导航系统为辅的组合导航方法.通过Kalman滤波技术对组合导航的误差状态进行了估计,并采用反馈校正的方法修正SINS的导航误差.仿真结果表明SINS/DVL/GPS的组合导航可以有效地提高水下航行器SINS/DVL组合导航系统的导航精度,满足AUV远距离航行的精度需求.     

Some results of the queueing system E/M/c

This paper analyses the E/M/c queueing system and shows how to calculate the expected number in the system, both at a random epoch and immediately preceding an arrival. These expectations are expressed in terms of certain initial probabilities which are determined by linear equations. The advantages and disadvantages of this method are also discussed.     

Performance analysis of queue length monitoring of M/G/1 systems

This study investigates the statistical process control application for monitoring queue length data in M/G/1 systems. Specifically, we studied the average run length (ARL) characteristics of two different control charts for detecting changes in system utilization. First, the nL chart monitors the sums of successive queue length samples by subgrouping individual observations with sample size n. Next is the individual chart with a warning zone whose control scheme is specified by two pairs of parameters, (upper control limit, d_u) and (lower control limit, d_l), as proposed by Bhat and Rao (Oper Res 20 (1972) 955–966). We will present approaches to calculate ARL for the two types of control charts using the Markov chain formulation and also investigate the effects of parameters of the control charts to provide useful design guidelines for better performance. Extensive numerical results are included for illustration. © 2011 Wiley Periodicals, Inc. Naval Research Logistics, 2011     

Matrix-geometric solution of discrete time MAP/PH/1 priority queue

We use the matrix-geometric method to study the discrete time MAP/PH/1 priority queue with two types of jobs. Both preemptive and non-preemptive cases are considered. We show that the structure of the R matrix obtained by Miller for the Birth-Death system can be extended to our Quasi-Birth-Death case. For both preemptive and non-preemptive cases the distributions of the number of jobs of each type in the system are obtained and their waiting times are obtained for the non-preemptive. For the preemptive case we obtain the waiting time distribution for the high priority job and the distribution of the lower priority job's wait before it becomes the leading job of its priority class. © 1998 John Wiley & Sons, Inc. Naval Research Logistics 45: 23–50, 1998     

烧结助剂对热压SiCw/Si3N4复合材料性能的影响

本文通过热压的方法分别制得以Ｙ２Ｏ３－Ａｌ２Ｏ３和Ｙ２Ｏ３－Ｌａ２Ｏ３为烧结助剂的ＳｉＣｗ／Ｓｉ３Ｎ４陶瓷基复合材料，对比了采用不同种类及含量的烧结助剂的ＳｉＣｗ／Ｓｉ３Ｎ４复合材料的性能结果，发现烧结助剂的种类及含量对ＳｉＣｗ／Ｓｉ３Ｎ４复合材料的弯曲强度和断裂韧性有明显的影响，对高温弯曲强度的影响尤为显著。